Synthesis and Dye-sensitized Solar Cell Application of Polyolefinic Aromatic Molecules with Pyrene as Surface Group

2011 ◽  
Vol 64 (7) ◽  
pp. 951 ◽  
Author(s):  
Perumal Rajakumar ◽  
Kathiresan Visalakshi ◽  
Shanmugam Ganesan ◽  
Pichai Maruthamuthu ◽  
Samuel Austin Suthanthiraraj
Keyword(s):  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Surface Group ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Solar Cell Application ◽  
Aromatic Molecules ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

Synthesis of polyolefinic aromatic molecules with pyrene as the surface group, and their role as an additive in the redox couple of dye-sensitized solar cells, is described. The studies yield a promising power conversion efficiency of 5.27% with a short circuit current density of 6.50 mA cm–2, an open circuit voltage of 0.60 V, and a fill factor of 0.54 under 40 mW cm–2 simulated air mass (A.M.) 1.5 illumination. Most importantly, the photocurrent responsivity increases with an increase in the number of pyrene units on the surface.

IMPROVING STABILITY OF CHLOROPHYLL AS NATURAL DYE FOR DYE-SENSITIZED SOLAR CELLS

2017 ◽  
Vol 80 (1) ◽  
Author(s):  
Zainal Arifin ◽  
Sudjito Soeparman ◽  
Denny Widhiyanuriyawan ◽  
Suyitno Suyitno ◽  
Argatya Tara Setyaji
Keyword(s):  
Current Density ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Natural Dyes ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

Natural dyes have attracted much researcher’s attention due to their low-cost production, simple synthesis processes and high natural abundance. However the dye-sensitized solar cells (DSSCs) based natural dyes have higher tendency to degradation. This article reports on the enhancement of performance and stability of dye-sensitized solar cells (DSSCs) using natural dyes. The natural dyes were extracted from papaya leaves by ethanol solvent at a temperature of 50 °C. Then the extracted dyes were isolated and modified into Mg-chlorophyll using column chromatography. Mg-chlorophyll was then synthesized into Fe-chlorophyll to improve stability. The natural dyes were characterized using ultraviolet-visible spectrometry, Fourier transform infrared spectroscopy, and cyclic voltammetry. The performance of DSSCs was tested using a solar simulator. The results showed the open-circuit voltage, the short-circuit current density, and the efficiency of the extracted papaya leaves-based DSSCs to be 325 mV, 0.36 mA/cm2, and 0.07%, respectively. Furthermore, the DSSCs with purified chlorophyll provide high open-circuit voltage of 425 mV and short-circuit current density of 0.45 mA/cm2. The use of Fe-chlorophyll for sensitizing the DSSCs increases the efficiency up to 2.5 times and the stability up to two times. The DSSCs with Fe-chlorophyll dyes provide open-circuit voltage, short-circuit current density, and efficiency of 500 mV, 0.62 mA/cm2, and 0.16%, respectively. Further studies to improve the current density and stability of natural dye-based DSSCs along with an improvement in the anchor between dyes and semiconducting layers are required.

Fabrication of a Dye Sensitized Solar Cell and Its Performance Dependence on Temperature and Irradiance

2011 ◽  
Author(s):  
Edwin Peng ◽  
Halil Berberoglu
Keyword(s):  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Dye Sensitized ◽  
Current Voltage ◽  
Nanocrystalline Titanium ◽  
Increasing Temperature ◽  
Sensitized Solar Cells

This paper reports the temperature and irradiance dependence of dye-sensitized solar cells (DSSCs) with acetonitrile-based electrolytes. The prototyped DSSCs had nanocrystalline titanium dioxide photoanodes and platinum thin film cathode. The photoanodes were sensitized with N-749 dye. The current-voltage characteristics of the DSSCs were measured at temperatures from 5 to 50 °C and under 500, 1000, and 1500 W m−2 irradiance. The open circuit voltage, VOC, decreased linearly with increasing temperature and had positive, logarithmic relation with irradiance. At temperatures lower than 15 °C, short circuit current density, JSC, was limited by the diffusion of I3− in the electrolyte and increased with increasing temperature. At higher temperatures the recombination of electrons injected into the TiO2 conduction band was dominant over diffusion and JSC decreased with increasing temperature. Moreover, JSC increaed linearly with increasing irradiance. The DSSC photoconversion efficiency did not vary appreciably at temperatures lower than 15 °C but decreased with increasing temperature. Finally, the efficiency increased with increasing irradiance.

scholarly journals Performance Degradation of Dye-Sensitized Solar Cells Induced by Electrolytes

2012 ◽  
Vol 2012 ◽  
pp. 1-4 ◽  
Author(s):  
Ru-Yuan Yang ◽  
Huang-Yu Chen ◽  
Fu-Der Lai
Keyword(s):  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Dye Sensitized ◽  
Oxidation Reduction ◽  
Oxidation Reduction Potential ◽  
Sensitized Solar Cells ◽  
Open Circuit Photovoltage

We investigated the change of the electric characteristics in dye-sensitized solar cell (DSSC) when the electrolyte has been injected and measured initially and lately for a period of time. It was found that the short-circuit current density decreased from 9.799 mA/cm2to 7.056 mA/cm2and the fill factor increased from 0.406 to 0.559 when the cell had stood for an hour, while the open-circuit photovoltage did not change due to fixed difference between the Fermi level of TiO2and the oxidation-reduction potential of electrolyte. The results can be explained by using the variation of the series resistance in the equivalent circuit of the DSSC.

The Preparation of TiO2 Nanotube by ZnO Nanorod Template Method and Application in Dye-Sensitized Solar Cells

2014 ◽  
Vol 602-603 ◽  
pp. 888-892
Author(s):  
Yan Xiang Wang ◽  
Yu Hong Ye ◽  
Jian Sun
Keyword(s):  
Seed Layer ◽  
Short Circuit ◽  
Zno Nanorods ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Immersion Method ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

Titanium dioxide (TiO2) nanotubes film was deposited on conducting glass oxide (FTO) by using ZnO nanorods as template, and the TiO2nanotubes film was applied in DSCs. First, ZnO nanorods were fabricated on ZnO-doped TiO2seed layer coated substrates by the hydrothermal method. Second, the obtained ZnO nanorods were used as a template to synthesize ZnOTiO2coreshell structure through the immersion method. Third, the ZnO nanorods template was removed by etching method to obtained TiO2nanotubes film. The thickness of ZnO-doped TiO2seed layer is about 200nm and the crystalline size of nanoparticles are about 5~10nm. The length of the ZnO nanorods are about 1~3μm. The TiO2nanotube was composed of TiO2nanoparticles. The short-circuit current density (Jsc), open-circuit voltage, fill factor (FF) and efficiency of TiO2nanotubes DSC were 4.63 mA·cm-2, 0.74V, 62% and 2.15%, respectively.

scholarly journals Partially nanowire-structured TiO2 electrode for dye-sensitized solar cells

2006 ◽  
Vol 4 (3) ◽  
pp. 476-488 ◽  
Author(s):  
Yoshikazu Suzuki ◽  
Supachai Ngamsinlapasathian ◽  
Ryuhei Yoshida ◽  
Susumu Yoshikawa
Keyword(s):  
Fill Factor ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Tio2 Electrode ◽  
One Dimensional ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

AbstractPartially nanowire-structured TiO2 was prepared by a hydrothermal processing followed by calcination in air. The hydrogen titanate powder as-synthesized was calcined at 300 °C for 4 h to obtain the partially nanowire-structured TiO2. A dye-sensitized solar cell (DSC) with a film thickness of 5.6 μm, fabricated using the partially nanowire-structured TiO2 showed better performance than using a fully nanowire-structured TiO2 or a conventional equi-axed TiO2 nanopowder. The short-circuit current density (JSC), the open-circuit voltage (VOC), the fill factor (FF) and the overall efficiency (η) are 11.9 mA/cm2, 0.754 V, 0.673 and 6.01 %, respectively. The effects of one-dimensional nanostructure and electron expressway concept are discussed.

Approach to tune short-circuit current and open-circuit voltage of dye-sensitized solar cells: π-linker modification and photoanode selection

RSC Advances ◽  
2014 ◽  
Vol 4 (80) ◽  
pp. 42252-42259 ◽  
Author(s):  
Shengbo Zhu ◽  
Zhongwei An ◽  
Xinbing Chen ◽  
Pei Chen ◽  
Qianfeng Liu
Keyword(s):  
Solar Cells ◽  
Current Density ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

The modification of the π-linker of cyclic thiourea functionalized dyes has a significant effect on the short-circuit current density and open-circuit voltage of dye-sensitized solar cells.

scholarly journals Electrolyte tuning in dye-sensitized solar cells with N-heterocyclic carbene (NHC) iron(II) sensitizers

2018 ◽  
Vol 9 ◽  
pp. 3069-3078 ◽  
Author(s):  
Mariia Karpacheva ◽  
Catherine E Housecroft ◽  
Edwin C Constable
Keyword(s):  
Ionic Liquid ◽  
Solar Cells ◽  
Electrochemical Impedance ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

We demonstrate that the performances of dye-sensitized solar cells (DSCs) sensitized with a previously reported N-heterocyclic carbene iron(II) dye in the presence of chenodeoxycholic acid co-adsorbant, can be considerably improved by altering the composition of the electrolyte while retaining an I−/I3 − redox shuttle. Critical factors are the solvent, presence of ionic liquid, and the use of the additives 1-methylbenzimidazole (MBI) and 4-tert-butylpyridine (TBP). For the electrolyte solvent, 3-methoxypropionitrile (MPN) is preferable to acetonitrile, leading to a higher short-circuit current density (J SC) with little change in the open-circuit voltage (V OC). For electrolytes containing MPN, an ionic liquid and MBI (0.5 M), DSC performance depended on the ionic liquid with 1-ethyl-3-methylimidazolium hexafluoridophosphate (EMIMPF) > 1,2-dimethyl-3-propylimidazolium iodide (DMPII) > 1-butyl-3-methylimidazolium iodide (BMII) ≈ 1-butyl-3-methylimidazolium hexafluoridophosphate (BMIMPF). Omitting the MBI leads to a significant improvement in J SC when the ionic liquid is DMPII, BMII or BMIMPF, but with EMIMPF the removal of the MBI additive results in a dramatic decrease in V OC (542 to 42 mV). For electrolytes containing MPN and DMPII, the effects of altering the MBI concentration have also been investigated. Although the addition of TBP improves V OC, it causes significant decreases in J SC. The best performing DSCs with the NHC-iron(II) dye employ an I−/I3 −-based electrolyte with MPN as solvent, DMPII ionic liquid (0.6 M) with no or 0.01 M MBI; values of J SC = 2.31 to 2.78 mA cm−2, V OC = 292 to 374 mV have been achieved giving η in the range of 0.47 to 0.57% which represents 7.8 to 9.3% relative to an N719 reference DSC set at 100%. Electrochemical impedance spectroscopy has been used to understand the role of the MBI additive in the electrolytes.

scholarly journals Delineating the enhanced efficiency of carbon nanomaterials including the hierarchical architecture of the photoanode of dye-sensitized solar cells

2020 ◽  
Vol 1 (8) ◽  
pp. 2964-2970
Author(s):  
Venkatesan Srinivasan ◽  
Jagadeeswari Sivanadanam ◽  
Kothandaraman Ramanujam ◽  
Mariadoss Asha Jhonsi
Keyword(s):  
Current Density ◽  
Carbon Nanomaterials ◽  
Short Circuit ◽  
Power Conversion ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Hierarchical Architecture ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

The inclusion of CNMs together with TiO2 enhanced the short circuit current density by 31% and power conversion efficiency (PCE) by 46% compared to the CNM-free DSSCs.

Inkjet Printing Technology for Dye-Sensitized Solar Cells

2012 ◽  
Vol 476-478 ◽  
pp. 1767-1770
Author(s):  
Yu Li Lin ◽  
Cheng Yi Hsu ◽  
Chang Lun Tai
Keyword(s):  
Open Circuit Voltage ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Dye Sensitized ◽  
Tio2 Particles ◽  
Ito Glass ◽  
Sensitized Solar Cells ◽  
Pet Substrate

The task of this study is to prepare the TiO2 film electrode for dye-sensitized solar cells (DSSC) on ITO PET substrate using a general jet-printer. The results were compared with that obtained using ITO glass substrate. In this study, the dispersion of TiO2 slurry was manipulated by changing the pH value of the solution to avoid agglomeration of TiO2 particles. The average TiO2 particles used in this study were measured about 130nm. The experimental results show that it has the best performance when the thickness of the TiO2 film was about 10μm. In ITO glass substrate, the measured short circuit current was about 5.03mA, the open circuit voltage was measured to be 0.65V. In ITO-PET substrate, the measured short circuit current was about 2.73mA, the open circuit voltage was measured to be 0.68V.

scholarly journals Prunus domestica dye extraction for fabrication of zinc oxide based dye-sensitized solar cells

BIBECHANA ◽  
2015 ◽  
Vol 13 ◽  
pp. 23-28
Author(s):  
Leela Pradhan Joshi
Keyword(s):  
Zinc Oxide ◽  
Solar Cells ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Zinc Nitrate ◽  
Open Circuit ◽  
Dye Sensitized ◽  
Dye Extraction ◽  
Sensitized Solar Cells

Aluminium doped Zinc Oxide (AZO) seed layers were deposited on Fluorine doped Tin Oxide (FTO) substrates using a spin coating technique. These were then immersed in growth solutions of zinc nitrate, hexamethylenetetramine and distilled water to develop nanoplates of Zinc Oxide (ZnO). The nanostructures of ZnO grown on FTO were studied using x-ray diffraction techniques. Dye-sensitized solar cells (DSSC) were fabricated using two prepared electrodes, one of dye-loaded zinc oxide and another that was platinum coated. The electrolyte used was potassium iodide iodine solution. The performance of the assembled DSCCs was tested by drawing an IV curve. The results showed that the short circuit current and open circuit voltages were about 10 microamperes and 270 millivolts respectively.BIBECHANA 13 (2016) 23-28

Sign in / Sign up

Export Citation Format

Share Document