THE OTWAY BASIN: EARLY CRETACEOUS RIFTING TO NEOGENE INVERSION

1995 ◽  
Vol 35 (1) ◽  
pp. 494 ◽  
Author(s):  
A.J. Buffin ◽  
A.J. Sutherland ◽  
J.A. Gorski
Keyword(s):  
Stress Field ◽  
Normal Fault ◽  
Horizontal Wells ◽  
Horizontal Stress ◽  
Natural Fracture ◽  
Water Flooding ◽  
Hydraulic Fractures ◽  
Vertical Wells ◽  
Minimum Horizontal Stress ◽  
Maximum Horizontal Stress

Borehole breakouts and hydraulic fractures in­ferred from dipmeter and formation microscanner logs indicate that the minimum horizontal stress (σh) is oriented 035°N in the South Australian sector of the Otway Basin. Density and sonic check-shot log data indicate that vertical stress (σv) increases from approximately 20 MPa at a depth of one km to 44 MPa at two km and 68 MPa at three km. Assum­ing a normal fault condition (i.e. σy > σH > σh), the magnitude of σh is 75 per cent of the magnitude of the maximum horizontal stress (σH), and the magni­tude of σH is close to that of av. Sonic velocity compaction trends for shales suggest that pore pressure is generally near hydrostatic in the Otway Basin.Knowledge of the contemporary stress field has a number of implications for hydrocarbon produc­tion and exploration in the basin. Wellbore quality in vertical wells may be improved (breakouts sup­pressed) by increasing the mud weight to a level below that which induces hydraulic fracture, or other drilling problems related to excessive mud weight. Horizontal wells drilled in the σh direction (035°N/215°N) should be more stable than those drilled in the σH direction, and indeed than vertical wells. In any EOR operations where water flooding promotes hydraulic fracturing, injectors should be aligned in the aH (125°N/305°N) direction, and off­set from producers in the orthogonal σh direction. Any deviated/horizontal wells targeting the frac­tured basement play should be oriented in the σh (035°N/215°N) direction to maximise intersection with this open, natural fracture trend. Hydrocar­bon recovery in wells deviated towards 035°N/215°N may also be enhanced by inducing multiple hydrau­lic fractures along the wellbore.Considering exploration-related issues, faults following the dominant structural trend, sub-paral­lel to σH orientation, are the most prone to be non-sealing during any episodic build-up of pore pres­sure. Pre-existing vertical faults striking 080-095°N and 155-170°N are the most prone to at least a component of strike-slip reactivation within the contemporary stress field.

Geomechanical Approach in Classification of Borehole Failures in Fractured Carbonates of Boca De Jaruco Field

2021 ◽  
Author(s):  
Anna Vladimirovna Norkina ◽  
Iaroslav Olegovich Simakov ◽  
Yuriy Anatoljevich Petrakov ◽  
Alexey Evgenjevich Sobolev ◽  
Oleg Vladimirovich Petrashov ◽  
...  
Keyword(s):  
Stress State ◽  
Horizontal Wells ◽  
Horizontal Stress ◽  
In Situ Stress ◽  
Vertical Wells ◽  
Stress Regime ◽  
Geophysical Information ◽  
The Republic ◽  
Maximum Horizontal Stress

Abstract This article is a continuation of the work on geomechanically calculations for optimizing the drilling of horizontal wells into the productive reservoir M at the Boca de Haruco field of the Republic of Cuba, presented in the article SPE-196897. As part of the work, an assessment of the stress state and direction was carried out using geological and geophysical information, an analysis of the pressure behavior during steam injections, cross-dipole acoustics, as well as oriented caliper data in vertical wells. After the completion of the first part of the work, the first horizontal wells were successfully drilled into the M formation. According to the recommendations, additional studies were carried out: core sampling and recording of micro-imager logging in the deviated sections. Presence of wellbore failures at the inclined sections allowed to use the method of inverse in-situ stress modeling based on image logs interpretation. The classification of wellbore failures by micro-imager logging: natural origin and violations of technogenic genesis is carried out. The type of breakout is defined. The result of the work was the determination of the stress state and horizontal stresses direction. In addition, the article is supplemented with the calculation of the maximum horizontal stress through the stress regime identifier factor.

scholarly journals Experimental Investigation on Propagation Behavior of Hydraulic Fractures in Coal Seam during Refracturing

Geofluids ◽  
2019 ◽  
Vol 2019 ◽  
pp. 1-15 ◽  
Author(s):  
Xun Sun ◽  
Shicheng Zhang ◽  
Xinfang Ma ◽  
Yushi Zou ◽  
Guanyu Lin
Keyword(s):  
Pore Pressure ◽  
Horizontal Stress ◽  
Stress Change ◽  
Hydraulic Fractures ◽  
Coal Seams ◽  
Initiation And Propagation ◽  
Hf Propagation ◽  
Minimum Horizontal Stress ◽  
Maximum Horizontal Stress ◽  
Study Laboratory

Refracturing is an effective technology for reinstituting a percolation path and improving the fracture conductivity in coal measure strata. Hydraulic fracture (HF) propagation is complicated due to the presence of cleats and stress change caused by pore pressure changes. Many scholars have studied HF propagation in the initial fracturing of coal, but the refracturing in coal seams is rarely mentioned. In this study, laboratory refracturing experiments were conducted on large natural coal specimens under various triaxial stress states to investigate the propagation of HFs in coal seams. The mechanical properties of coal were tested before refracturing. The maximum and the minimum horizontal principal stresses are inverted to simulate the stress change caused by the production and pore pressure reduction of the stress condition after initial fracturing. Experimental results showed three different types of HF initiation and propagation during refracturing: (1) under low horizontal stress differences (0-2 MPa), HF propagated along the cleats, and no new HFs were formed on the walls of the initial HFs regardless of changes in the horizontal stress; (2) under high horizontal stress differences (4–8 MPa) with no stress inversion, a major HF was initiated parallel to the orientation of maximum horizontal stress during initial fracturing; new branches propagated along cleats in the orientation of the minimum horizontal stress during refracturing; and (3) under high horizontal stress differences (4–8 MPa) with maximum and minimum horizontal stress inversions, the main HF formed along the orientation of the maximum horizontal stress, and a new HF perpendicular to the initial HF was formed during refracturing. Multiple factors affect fracture morphology during refracturing. Cleats affect the HF growth path and the creation of new branches. The in situ stress determines the initiation and propagation of new HFs.

Geodynamic implications of the Cenozoic stress field on Seymour Island, West Antarctica

2008 ◽  
Vol 20 (2) ◽  
pp. 173-184 ◽  
Author(s):  
A. Maestro ◽  
J. López-Martínez ◽  
F. Bohoyo ◽  
M. Montes ◽  
F. Nozal ◽  
...  
Keyword(s):  
Stress Field ◽  
Antarctic Peninsula ◽  
Horizontal Stress ◽  
Weddell Sea ◽  
Scotia Sea ◽  
Compressional Stress ◽  
The North ◽  
Stress States ◽  
Bransfield Basin ◽  
Minimum Horizontal Stress

AbstractPalaeostress inferred from brittle mesostructures in Seymour (Marambio) Island indicates a Cenozoic to Recent origin for an extensional stress field, with only local compressional stress states. Minimum horizontal stress (σ3) orientations are scattered about two main NE–SW and NW–SE modes suggesting that two stress sources have been responsible for the dominant minimum horizontal stress directions in the north-western Weddell Sea. Extensional structures within a broad-scale compressional stress field can be linked to both the decrease in relative stress magnitudes from active margins to intraplate regions and the rifting processes that occurred in the northern Weddell Sea. Stress states with NW–SE trending σ3are compatible with back-arc extension along the eastern Antarctic Peninsula. We interpret this as due to the opening of the Larsen Basin during upper Cretaceous to Eocene and to the spreading, from Pliocene to present, of the Bransfield Basin (western Antarctic Peninsula), both due to former Phoenix Plate subduction under the Antarctic Plate. NE–SW σ3orientations could be expressions of continental fragmentation of the northern Antarctic Peninsula controlling eastwards drifting of the South Orkney microcontinent and other submerged continental blocks of the southern Scotia Sea.

A Novel Method and its Application to Define Maximum Horizontal Stress and Stress Path

2021 ◽  
Author(s):  
Jianguo Zhang ◽  
Karthik Mahadev ◽  
Stephen Edwards ◽  
Alan Rodgerson
Keyword(s):  
Fracture Initiation ◽  
Stress Path ◽  
Horizontal Stress ◽  
Geomechanical Model ◽  
Breakdown Pressure ◽  
In Situ Stresses ◽  
Fracture Closure ◽  
Minimum Horizontal Stress ◽  
Maximum Horizontal Stress

Abstract Maximum horizontal stress (SH) and stress path (change of SH and minimum horizontal stress with depletion) are the two most difficult parameters to define for an oilfield geomechanical model. Understanding these in-situ stresses is critical to the success of operations and development, especially when production is underway, and the reservoir depletion begins. This paper introduces a method to define them through the analysis of actual minifrac data. Field examples of applications on minifrac failure analysis and operational pressure prediction are also presented. It is commonly accepted that one of the best methods to determine the minimum horizontal stress (Sh) is the use of pressure fall-off analysis of a minifrac test. Unlike Sh, the magnitude of SH cannot be measured directly. Instead it is back calculated by using fracture initiation pressure (FIP) and Sh derived from minifrac data. After non-depleted Sh and SH are defined, their apparent Poisson's Ratios (APR) are calculated using the Eaton equation. These APRs define Sh and SH in virgin sand to encapsulate all other factors that influence in-situ stresses such as tectonic, thermal, osmotic and poro-elastic effects. These values can then be used to estimate stress path through interpretation of additional minifrac data derived from a depleted sand. A geomechanical model is developed based on APRs and stress paths to predict minifrac operation pressures. Three cases are included to show that the margin of error for FIP and fracture closure pressure (FCP) is less than 2%, fracture breakdown pressure (FBP) less than 4%. Two field cases in deep-water wells in the Gulf of Mexico show that the reduction of SH with depletion is lower than that for Sh.

Rock physics of the Wolfcamp Formation, Delaware Basin

Geophysics ◽  
2019 ◽  
Vol 84 (6) ◽  
pp. B353-B361 ◽  
Author(s):  
Colin M. Sayers ◽  
Sagnik Dasgupta ◽  
Adam Koesoemadinata ◽  
Michael Shoemaker
Keyword(s):  
Anisotropy Parameter ◽  
Rock Physics ◽  
Horizontal Stress ◽  
P Wave ◽  
Seismic Survey ◽  
Hydraulic Fractures ◽  
Anisotropic Rock ◽  
Delaware Basin ◽  
Organic Carbon Concentration ◽  
Minimum Horizontal Stress

Production from wells in organic-rich shales often shows considerable lateral variation. Reliable predrill methods to characterize the lateral heterogeneity of such reservoirs are required to optimize the trajectory of lateral wells in these low-permeability reservoirs. Petrophysical interpretation of measured well logs provides information on mineral, porosity, and kerogen content. Combining the results of petrophysical analysis with P-wave, S-wave, and density logs allows generation of a probability density function (PDF) for each of the different significant lithofacies. The PDFs are applied to the P- and S-impedance from prestack seismic amplitude variation with offset inversion to predict the spatial variation in the distribution of lithofacies and associated probability for the Wolfcamp Formation in an area covered by a 3D seismic survey in the Delaware Basin, West Texas. An anisotropic rock-physics model for the Wolfcamp Formation allows the effect of complex mineralogy, organic carbon concentration, and porosity on the P- and S-impedance to be investigated. Kerogen inclusions and pores act to increase Thomsen’s anisotropy parameter [Formula: see text] relative to [Formula: see text], and there is a competition between clay matrix anisotropy and inclusion shape anisotropy in determining the anisotropy of the rock. Inclusions with isotropic elastic properties act to decrease the anisotropy due to the dilution effect, but this decrease is partially offset by the increase in anisotropy due to the anisotropic shape of the inclusions. Application of the model to the determination of minimum horizontal stress indicates that kerogen-rich siliceous shales have the lowest value of minimum horizontal stress, whereas silica-rich calcareous shales, mixed siliceous shales, and clay-rich siliceous shales have higher values and may therefore act as barriers for the vertical growth of hydraulic fractures.

A New Uniform Moment Tensor Catalog for Yunnan, China, from January 2000 through December 2014

2020 ◽  
Vol 91 (2A) ◽  
pp. 891-900
Author(s):  
Yan Xu ◽  
Keith D. Koper ◽  
Relu Burlacu ◽  
Robert B. Herrmann ◽  
Dan-Ning Li
Keyword(s):  
Stress Field ◽  
Seismic Hazard ◽  
Moment Tensor ◽  
Horizontal Stress ◽  
Strike Slip ◽  
Moment Tensors ◽  
Yunnan Region ◽  
Seismic Waveforms ◽  
The Moment ◽  
Maximum Horizontal Stress

Abstract Because of the collision of the Indian and Eurasian tectonic plates, the Yunnan Province of southwestern China has some of the highest levels of seismic hazard in the world. In such a region, a catalog of moment tensors is important for estimating seismic hazard and helping understand the regional seismotectonics. Here, we present a new uniform catalog of moment tensor solutions for the Yunnan region. Using a grid-search technique to invert seismic waveforms recorded by the permanent regional network in Yunnan and the 2 yr ChinArray deployment, we present 1833 moment tensor solutions for small-to-moderate earthquakes that occurred between January 2000 and December 2014. Moment magnitudes in the new catalog vary from Mw 2.2 to 6.1, and the catalog is complete above Mw∼3.5–3.6. The moment tensors are constrained to be purely double-couple and show a variety of faulting mechanisms. Normal faulting events are mainly concentrated in northwest Yunnan, while farther south along the Sagaing fault the earthquakes are mostly thrust and strike slip. The remaining area includes all three styles of faulting but mostly strike slip. We invert the moment tensors for the regional stress field and find a strong correlation between spatially varying maximum horizontal stress and Global Positioning System observations of horizontal ground velocity. The stress field reveals clockwise rotation around the eastern Himalayan syntaxis, with northwest–southeast compression to the east of the Red River fault changing to northeast–southwest compression west of the fault. Almost 88% of the centroid depths are shallower than 16 km, consistent with a weak and ductile lower crust.

PRESENT-DAY STATE-OF-STRESS OF SOUTHEAST AUSTRALIA

2006 ◽  
Vol 46 (1) ◽  
pp. 283 ◽  
Author(s):  
E. Nelson ◽  
R. Hillis ◽  
M. Sandiford ◽  
S. Reynolds ◽  
S. Mildren
Keyword(s):  
Focal Mechanism ◽  
Horizontal Stress ◽  
Strike Slip ◽  
Focal Mechanism Solutions ◽  
Southeast Australia ◽  
State Of Stress ◽  
Earthquake Focal Mechanism ◽  
Minimum Horizontal Stress ◽  
Maximum Horizontal Stress ◽  
Gippsland Basin

There have been several studies, both published and unpublished, of the present-day state-of-stress of southeast Australia that address a variety of geomechanical issues related to the petroleum industry. This paper combines present-day stress data from those studies with new data to provide an overview of the present-day state-of-stress from the Otway Basin to the Gippsland Basin. This overview provides valuable baseline data for further geomechanical studies in southeast Australia and helps explain the regional controls on the state-of-stress in the area.Analysis of existing and new data from petroleum wells reveals broadly northwest–southeast oriented, maximum horizontal stress with an anticlockwise rotation of about 15° from the Otway Basin to the Gippsland Basin. A general increase in minimum horizontal stress magnitude from the Otway Basin towards the Gippsland Basin is also observed. The present-day state-of-stress has been interpreted as strike-slip in the South Australian (SA) Otway Basin, strike-slip trending towards reverse in the Victorian Otway Basin and borderline strike-slip/reverse in the Gippsland Basin. The present-day stress states and the orientation of the maximum horizontal stress are consistent with previously published earthquake focal mechanism solutions and the neotectonic record for the region. The consistency between measured present-day stress in the basement (from focal mechanism solutions) and the sedimentary basin cover (from petroleum well data) suggests a dominantly tectonic far-field control on the present-day stress distribution of southeast Australia. The rotation of the maximum horizontal stress and the increase in magnitude of the minimum horizontal stress from west to east across southeast Australia may be due to the relative proximity of the New Zealand segment of the plate boundary.

Application of Research of the Relationship between Ground Stress and Fractures in the Trajectory Optimization of Horizontal Wells

2013 ◽  
Vol 765-767 ◽  
pp. 300-306
Author(s):  
Hui Zhang ◽  
Fang Jun Ou ◽  
Guo Qing Yin ◽  
Jing Bing Yi ◽  
Fang Yuan ◽  
...  
Keyword(s):  
Stress State ◽  
Stress Field ◽  
Trajectory Optimization ◽  
Horizontal Wells ◽  
Wellbore Stability ◽  
Natural Fracture ◽  
Fracture System ◽  
Well Trajectory ◽  
The Stability ◽  
The Relationship

From the perspective of improving single well production and wellbore stability, stress field and natural fractures are the factors which have to be taken into account in the development of horizontal wells of the complex carbonate oil and gas fields in Kuqa piedmont and platform-basin transitional area. On the one hand, as the present stress field is the key factor to control fracture permeability, the trajectory of horizontal wells should pass through fracture system with good permeability as much as possible, being conducive to the effective stimulation of the reservoir. On the other hand, at the state of specific stress, the stability of well trajectory varies with directions. Therefore, before drilling horizontal wells, it is necessary to fully analyze the quantitative relationship between the present stress state and natural fracture occurrence and mechanical characteristics, etc., to optimize and determine a well trajectory conducive to high yield and wellbore stability. In this study, firstly, the fundamental principles for evaluating the present stress state and analyzing the relationship between the stress and fractures were described. Then based on the relationship between them, the occurrence and longitudinal positions of permeability fractures were analyzed. Apart from that, the stability index and fracture opening pressure distribution of wells in different directions at given stress state and fracture system were also analyzed. Finally, the optimization scheme for trajectory of horizontal wells under complex conditions was discussed with three aspects taken into account, i.e. best drilling in permeability fractures, wellbore stability and drilled reservoir stimulation.

scholarly journals Geomechanical Analysis to Avoid Serious Drilling Hazards in Zubair Oilfield, Southern Iraq

2020 ◽  
pp. 1994-2003
Author(s):  
Shaban Dharb Shaban ◽  
Hassan Abdul Hadi
Keyword(s):  
Gamma Ray ◽  
Mechanical Test ◽  
Horizontal Wells ◽  
Failure Criteria ◽  
Horizontal Stress ◽  
Wellbore Instability ◽  
Geomechanical Analysis ◽  
Safe Mud Window ◽  
Rock Mechanical Properties ◽  
Minimum Horizontal Stress

Zubair oilfield is an efficient contributor to the total Iraqi produced hydrocarbon. Drilling vertical wells as well as deviated and horizontal wells have been experiencing intractable challenges. Investigation of well data showed that the wellbore instability issues were the major challenges to drill in Zubair oilfield. These experienced borehole instability problems are attributed to the increase in the nonproductive time (NPT). This study can assist in managing an investment-drilling plan with less nonproductive time and more efficient well designing.       To achieve the study objectives, a one dimension geomechanical model (1D MEM) was constructed based on open hole log measurements, including Gamma-ray (GR), Caliper (CALI), Density (RHOZ), sonic compression (DTCO) and shear (DTSM) wave velocities , and Micro imager log (FMI). The determined 1D MEM components, i.e., pore pressure, rock mechanical properties, in-situ principal stress magnitudes and orientations, were calibrated using the data acquired from repeated formation test (RFT), hydraulic fracturing test (Mini-frac), and laboratory rock core mechanical test (triaxial test). Then, a validation model coupled with three failure criteria, i.e., Mohr-Coulomb, Mogi-Coulomb, and Modified lade, was conducted using the Caliper and Micro-imager logs. Finally, sensitivity and forecasting stability analyses were implemented to predict the most stable wellbore trajectory concerning the safe mud window for the planned wells.    The implemented wellbore instability analysis utilizing Mogi-Coulomb criterion demonstrated that the azimuth of 140o paralleling to the minimum horizontal stress is preferable to orient deviated and horizontal wells. The vertical and slightly deviated boreholes (1ess than 30o) are the most stable wellbores, and they are recommended to be drilled with 11.6 -12 ppg mud weight. The highly deviated and horizontal wells are recommended to be drilled with a mud weight of 12-12.6 ppg.

Sign in / Sign up

Export Citation Format

Share Document