DEVELOPMENT OF THE WOODADA GAS FIELD

1985 ◽  
Vol 25 (1) ◽  
pp. 316
Author(s):  
C.M. Lane ◽  
R.J. Watson
Keyword(s):  
Gas Production ◽  
Commercial Production ◽  
Permeability Barrier ◽  
Production Mechanism ◽  
Well Bore ◽  
Secondary Porosity ◽  
Gas Field ◽  
The Matrix ◽  
Production History ◽  
Matrix Rock

The Woodada gas field was discovered in May 1980, when the Woodada 1 well flowed gas at a rate of seven million cubic feet per day from a carbonate unit within the Carynginia Formation of the onshore northern Perth Basin. Appraisal and development drilling has resulted in a total of 11 wells, of which seven have produced sales gas.The reservoir is estimated to have contained initially at least forty four billion cubic feet of gas-in-place in the developed part. There is a prospective area to the south with similar potential.The Woodada field is a combination structural/strati- graphic trap, where an up-dip lithology change effecting a permeability barrier seals the reservoir across a north plunging anticline. Porosity within the reservoir is secondary, with natural fractures often contributing to the production mechanism. The presence of fractures has required special attention to drilling and completion techniques. Gas production is significantly enhanced by acidization.Pressure responses measured in or between wells combined with more than two years of production history have demonstrated that there is moveable gas in the fine voids of the matrix rock, as well as in the better developed secondary porosity system. Even where there is no substantial porosity in a well bore, it has been possible to achieve commercial production rates by acid stimulation.

scholarly journals Structural Reservoir Characterization of Akkas Gas Field, Western Iraq: Implications for Hydrocarbon Recovery

2021 ◽  
pp. 4769-4778
Author(s):  
Abdulkhaleq A. Alhadithi
Keyword(s):  
Reservoir Characterization ◽  
Gas Production ◽  
Secondary Porosity ◽  
Gas Field ◽  
Horizontal Drilling ◽  
Hinge Line ◽  
Hydrocarbon Recovery ◽  
Fracture Surfaces ◽  
Bedding Planes ◽  
Brittle Sandstone

     Akkas Field is a structural trap with a sandstone reservoir that contains proven gas condensate. The field is a faulted anticline that consists of the Ordovician Khabour Formation. The objective of this research is to use structural reservoir characterization for hydrocarbon recovery. The stratigraphic sequence of the Silurian and older strata was subjected to an uplift that developed a gentle NW-SE trending anticline. The uplifting and folding events developed micro-fractures represented by tension cracks.  These microfractures, whether they are outer arc or release fractures, are parallel to the hinge line of the anticline and perpendicular to the bedding planes. The brittle sandstone layers of the reservoir are interbedded with ductile units of shale. The sandstone layers accommodate the formation of micro fractures that play a major role to increase the secondary porosity. The gas and condensate have been stored mainly through the micro fractures. Two types of drilling have been used for experimental gas production, vertical and horizontal. Horizontal drilling was parallel to both hinge line of the anticline and micro fracture surfaces that was conducted and doubled the gas production of the vertical well multiple times. However, if used the third type of drilling, directional, that is perpendicular to the hinge line and parallel to the beddings of both flanks of the anticline gas production will increase more than the horizontal drilling. The directional drilling will become perpendicular to the fracture surfaces and allow the gas and the condensate to flow into the well from all directions. Additionally, it will reduce the effect of both semi – liquid hydrocarbon condensate and vertical sediment barriers.

Natural fractures in tight gas sandstones: a case study of the Upper Triassic Xujiahe Formation in Xinchang gas field, Western Sichuan Basin, China

2021 ◽  
pp. 1-18
Author(s):  
Yunzhao Zhang ◽  
Lianbo Zeng ◽  
Wenya Lyu ◽  
Dongsheng Sun ◽  
Shuangquan Chen ◽  
...  
Keyword(s):  
Production Capacity ◽  
Gas Production ◽  
Upper Triassic ◽  
Tight Gas ◽  
Natural Fractures ◽  
Carbon And Oxygen Isotopes ◽  
Gas Field ◽  
Xujiahe Formation ◽  
Western Sichuan ◽  
Tight Gas Reservoir

Abstract The Upper Triassic Xujiahe Formation is a typical tight gas reservoir in which natural fractures determine the migration, accumulation and production capacity of tight gas. In this study, we focused on the influences of natural fractures on the tight gas migration and production. We clarified characteristics and attributes (i.e. dips, apertures, filling degree and cross-cutting relationships) of the fractures based on image logging interpretations and core descriptions. Previous studies of electron spin resonance, carbon and oxygen isotopes, homogenization temperature of fluid inclusions analysis and basin simulation were considered. This study also analysed the fracture sequences, source of fracture fillings, diagenetic sequences and tight gas enrichment stages. We obtained insight into the relationship between fracture evolution and hydrocarbon charging, particularly the effect of the apertures and intensity of natural fractures on tight gas production. We reveal that the bedding fractures are short horizontal migration channels of tight gas. The tectonic fractures with middle, high and nearly vertical angles are beneficial to tight gas vertical migration. The apertures of fractures are controlled by the direction of maximum principal stress and fracture angle. The initial gas production of the vertical wells presents a positive correlation with the fracture abundance, and the intensity and aperture of fractures are the fundamental factors that determine the tight gas production. With these findings, this study is expected to guide the future exploration and development of tight gas with similar geological backgrounds.

scholarly journals Evaluation of natural gas production optimization in Kailashtila gas field in Bangladesh using decline curve analysis method

2015 ◽  
Vol 50 (1) ◽  
pp. 29-38 ◽  
Author(s):  
MS Shah ◽  
HMZ Hossain
Keyword(s):  
Production System ◽  
Gas Production ◽  
Curve Analysis ◽  
Production Optimization ◽  
Reservoir Pressure ◽  
Gas Field ◽  
Wellhead Pressure ◽  
Decline Curve Analysis ◽  
Decline Curve ◽  
Overall Performance

Decline curve analysis of well no KTL-04 from the Kailashtila gas field in northeastern Bangladesh has been examined to identify their natural gas production optimization. KTL-04 is one of the major gas producing well of Kailashtila gas field which producing 16.00 mmscfd. Conventional gas production methods depend on enormous computational efforts since production systems from reservoir to a gathering point. The overall performance of a gas production system is determined by flow rate which is involved with system or wellbore components, reservoir pressure, separator pressure and wellhead pressure. Nodal analysis technique is used to performed gas production optimization of the overall performance of the production system. F.A.S.T. Virtu Well™ analysis suggested that declining reservoir pressure 3346.8, 3299.5, 3285.6 and 3269.3 psi(a) while signifying wellhead pressure with no changing of tubing diameter and skin factor thus daily gas production capacity is optimized to 19.637, 24.198, 25.469, and 26.922 mmscfd, respectively.Bangladesh J. Sci. Ind. Res. 50(1), 29-38, 2015

A Dynamic Workflow of Well Health Issue Prediction – Sulfur Deposition

2021 ◽  
Author(s):  
Bashirul Haq
Keyword(s):  
Material Balance ◽  
Gas Production ◽  
Health Issue ◽  
Sulfur Deposition ◽  
Gas Reservoirs ◽  
Gas Field ◽  
Actual Performance ◽  
Sulphur Deposition ◽  
Balance Analysis ◽  
Sour Gas

Abstract Sour gas reservoirs are vital sources for natural gas production. Sulphur deposition in the reservoir reduces a considerable amount of gas production due to permeability reduction. Consequently, well health monitoring and early prediction of Sulphur deposition are crucial for effective gas production from a sour gas reservoir. Dynamic gas material balance analysis is a useful technique in calculating gas initially in place utilizing the flowing wellhead or bottom hole pressures and rates during the well's lifetime. The approach did not apply to monitor a producing gas's health well and detect Sulphur deposition. This work aims to (i) modify dynamic gas material balance equation by adding the Sulphur deposition term, (ii) build a model to predict and validate the issue utilizing the modified equation. A unique form of the flowing material balance is developed by including Sulphur residue term. The curve fitting tool and modified flowing gas material balance are applied to predict well-expected behaviour. The variation between expected and actual performance indicates the health issue of a well. Initial, individual components of the model are tested. Then the model is validated with the known values. The workflow is applied to active gas field and correctly detected the health issue. The novel workflow can accurately predict Sulphur evidence. Besides,the workflow can notify the production engineers to take corrective measures about the subject. Keywords: Sulfur deposition, Dynamic gas material balance analysis, Workflow

scholarly journals Drill core from seismically active sandstone gas reservoir yields clues to internal deformation mechanisms

Geology ◽  
2020 ◽  
Author(s):  
Berend A. Verberne ◽  
Suzanne J.T. Hangx ◽  
Ronald P.J. Pijnenburg ◽  
Maartje F. Hamers ◽  
Martyn R. Drury ◽  
...  
Keyword(s):  
Microstructural Analysis ◽  
Gas Production ◽  
Drill Core ◽  
Gas Reservoir ◽  
Gas Field ◽  
Reservoir Compaction ◽  
Key Factor ◽  
Forecasting System ◽  
Internal Deformation ◽  
Dauphiné Twinning

Europe’s largest gas field, the Groningen field (the Netherlands), is widely known for induced subsidence and seismicity caused by gas pressure depletion and associated compaction of the sandstone reservoir. Whether compaction is elastic or partly inelastic, as implied by recent experiments, is a key factor in forecasting system behavior and seismic hazard. We sought evidence for inelastic deformation through comparative microstructural analysis of unique drill core recovered from the seismogenic center of the field in 2015, 50 yr after gas production started, versus core recovered before production (1965). Quartz grain fracturing, crack healing, and stress-induced Dauphiné twinning are equally developed in the 2015 and 1965 cores, with the only measurable effect of gas production being enhanced microcracking of sparse K-feldspar grains in the 2015 core. Interpreting these grains as strain markers, we suggest that reservoir compaction involves elastic strain plus inelastic compression of weak clay films within grain contacts.

scholarly journals Research on Gas-liquid Mixed Transportation Technological Adaptability: A Case Study of the Western Sichuan Gas Field

2017 ◽  
Vol 10 (1) ◽  
pp. 37-47
Author(s):  
Qingsha Zhou ◽  
Kun Huang ◽  
Yongchun Zhou
Keyword(s):  
Flow Simulation ◽  
Field Tests ◽  
Economic Benefits ◽  
Gas Production ◽  
Simulation Software ◽  
Rapid Decline ◽  
Gas Field ◽  
Western Sichuan ◽  
Field Development ◽  
Well Production

Background: The western Sichuan gas field belongs to the low-permeability, tight gas reservoirs, which are characterized by rapid decline in initial production of single-well production, short periods of stable production, and long periods of late-stage, low-pressure, low-yield production. Objective: It is necessary to continue pursuing the optimization of transportation processes. Method: This paper describes research on mixed transportation based on simplified measurements with liquid-based technology and the simulation of multiphase processes using the PIPEPHASE multiphase flow simulation software to determine boundary values for the liquid carrying process. Conclusion: The simulation produced several different recommendations for the production and maximum multiphase distance along with difference in elevation. Field tests were then conducted to determine the suitability of mixed transportation in western Sichuan, so as to ensure smooth progress with fluid metering, optimize the gathering process in order to achieve stable and efficient gas production, and improve the economic benefits of gas field development.

scholarly journals Fluid pressure arrival-time tomography: Estimation and assessment in the presence of inequality constraints with an application to production at the Krechba field, Algeria

Geophysics ◽  
2010 ◽  
Vol 75 (6) ◽  
pp. O39-O55 ◽  
Author(s):  
Alessio Rucci ◽  
D. W. Vasco ◽  
Fabrizio Novali
Keyword(s):  
Surface Deformation ◽  
Transient Flow ◽  
Fluid Pressure ◽  
Inequality Constraints ◽  
Gas Production ◽  
Gas Field ◽  
Peak Displacement ◽  
Geomechanical Properties ◽  
Fluid Production ◽  
Using Data

Deformation in the overburden proves useful in deducing spatial and temporal changes in the volume of a producing reservoir. Based on these changes, we have estimated diffusive traveltimes associated with the transient flow due to production, and then, as the solution of a linear inverse problem, the effective permeability of the reservoir. An advantage of the approach based on traveltimes, as opposed to one based on the amplitude of surface deformation, is that it is much less sensitive to the exact geomechanical properties of the reservoir and overburden. Inequalities constrain the inversion, under the assumption that the fluid production only results in pore volume decreases within the reservoir. The formulation has been applied to satellite-based estimates of deformation in the material overlying a thin gas production zone at the Krechba field in Algeria. The peak displacement after three years of gas production is found to be approximately [Formula: see text], overlying the eastern margin of the anticlinal structure defining the gas field. Using data from 15 irregularly spaced images of range change, we have calculated the diffusive traveltimes associated with the startup of a gas production well. The inequality constraints were incorporated into the estimates of model parameter resolution and covariance, improving the resolution by roughly 30% to 40%.

Comprehensive Analysis of Production Loggings in Fuling Shale Gas Play in China

2021 ◽  
Author(s):  
Yaowen Liu ◽  
Wei Pang ◽  
Jincai Shen ◽  
Ying Mi
Keyword(s):  
Shale Gas ◽  
Mineral Content ◽  
Horizontal Wells ◽  
Organic Content ◽  
Gas Production ◽  
Liquid Loading ◽  
Comprehensive Overview ◽  
Gas Field ◽  
Well Trajectory ◽  
Positive Effect

Abstract Fuling shale gas field is one of the most successful shale gas play in China. Production logging is one of the vital technologies to evaluate the shale gas contribution in different stages and different clusters. Production logging has been conducted in over 40 wells and most of the operations are successful and good results have been observed. Some previous studies have unveiled one or several wells production logging results in Fuling shale gas play. But production logging results show huge difference between different wells. In order to get better understanding of the results, a comprehensive overview is carried out. The effect of lithology layers, TOC (total organic content), porosity, brittle mineral content, well trajectory is analyzed. Results show that the production logging result is consistent with the geology understanding, and fractures in the favorable layers make more gas contribution. Rate contribution shows positive correlation with TOC, the higher the TOC, the greater the rate contribution per stage. For wells with higher TOC, the rate contribution difference per stage is relatively smaller, but for wells with lower TOC, it shows huge rate contribution variation, fracture stages with TOC lower than 2% contribute very little, and there exist one or several dominant fractures which contributes most gas rate. Porosity and brittle minerals also show positive effect on rate contribution. The gas rate contribution per fracture stage increases with the increase of porosity and brittle minerals. The gas contribution of the front half lateral and that of latter half lateral are relatively close for the "upward" or horizontal wells. However, for the "downward" wells, the latter half lateral contribute much more gas than the front half lateral. It is believed that the liquid loading in the toe parts reduced the gas contribution in the front half lateral. The overview research is important to get a compressive understanding of production logging and different fractures’ contribution in shale gas production. It is also useful to guide the design of horizontal laterals and fractures scenarios design.

A petrographic study of the Rotliegendes Sandstone reservoir (Lower Permian) in the Rough Gas Field

Clay Minerals ◽  
1986 ◽  
Vol 21 (4) ◽  
pp. 459-477 ◽  
Author(s):  
M. W. Goodchild ◽  
J. H. McD. Whitaker
Keyword(s):  
Sedimentary Facies ◽  
Mineral Dissolution ◽  
Lower Permian ◽  
Secondary Porosity ◽  
Gas Field ◽  
Thin Sections ◽  
Fine Grained ◽  
Groundwater Movement ◽  
Marked Variability ◽  
Sandstone Reservoir

AbstractThe diagenetic history of the Rotliegendes Sandstone reservoir in the Rough Gas Field was studied using thin-sections, XRD analyses and SEM. The Rotliegendes comprises a sequence of fine-grained fluvial sheet-flood sandstones and coarse, gravelly, low-sinuosity channel sandstones, with thin aeolian interbeds, overlain by a sequence of aeolian dune and interdune sandstones. Early, environmentally-related diagnesis (eogenesis) shows a marked variability with sedimentary facies. Within aeolian sandstones, poikilotopic anhydrite and fine, rhombic dolomite are preserved. Fluvially-derived sandstones typically contain infiltrated detrital clays and early authigenic mixed-layer clays, together with coarse, framework-displacive dolomite. Feldspars show varying degrees of alteration within all facies. These eogenetic features reflect patterns of groundwater movement during the Rotliegendes and early Zechstein. Mineral dissolution and precipitation were controlled by the chemistry of the groundwaters. Burial diagenetic (mesogenetic) features are superimposed on eogenetic cements. Authigenic clays have been converted to illitic clays. In addition, mesogenetic chlorite has formed and quartz and strongly ferroan dolomite cements are recognized. These minerals may be related to clay diagenesis within the underlying Carboniferous Coal Measures. Early, framework-supporting anyhdrite, and both phases of dolomite, have been partially dissolved, creating secondary porosity. This is attributed to the action of acidic porewaters, generated by the maturation of organic material within the Carboniferous. Post-dissolution kaolinite, gypsum and minor pyrite infill secondary pores. Gas emplacement from the Late Cretaceous onwards effectively halted further diagenetic reactions.

A review of gasification of bio-oil for gas production

2019 ◽  
Vol 3 (7) ◽  
pp. 1600-1622 ◽  
Author(s):  
Ji-Lu Zheng ◽  
Ya-Hong Zhu ◽  
Ming-Qiang Zhu ◽  
Kang Kang ◽  
Run-Cang Sun
Keyword(s):  
Large Scale ◽  
Cost Effective ◽  
Gas Production ◽  
Commercial Production ◽  
Advanced Fuels ◽  
Bio Oil ◽  
Effective Transport ◽  
The Cost

The commercial production of advanced fuels based on bio-oil gasification could be promising because the cost-effective transport of bio-oil could promote large-scale implementation of this biomass technology.

Sign in / Sign up

Export Citation Format

Share Document