Full waveform inversion: early start of model building process to resolve the complex near surface model in the Exmouth sub-basin, North West Shelf Australia

2018 ◽  
Vol 58 (2) ◽  
pp. 884
Author(s):  
Lianping Zhang ◽  
Haryo Trihutomo ◽  
Yuelian Gong ◽  
Bee Jik Lim ◽  
Alexander Karvelas
Keyword(s):  
Model Building ◽  
Waveform Inversion ◽  
Velocity Model ◽  
Surface Velocity ◽  
Image Point ◽  
Surface Model ◽  
Full Waveform Inversion ◽  
Near Surface ◽  
North West ◽  
Full Waveform

The Schlumberger Multiclient Exmouth 3D survey was acquired over the Exmouth sub-basin, North West Shelf Australia and covers 12 600 km2. One of the primary objectives of this survey was to produce a wide coverage of high quality imaging with advanced processing technology within an agreed turnaround time. The complexity of the overburden was one of the imaging challenges that impacted the structuration and image quality at the reservoir level. Unlike traditional full-waveform inversion (FWI) workflow, here, FWI was introduced early in the workflow in parallel with acquisition and preprocessing to produce a reliable near surface velocity model from a smooth starting model. FWI derived an accurate and detailed near surface model, which subsequently benefitted the common image point (CIP) tomography model updates through to the deeper intervals. The objective was to complete the FWI model update for the overburden concurrently with the demultiple stages hence reflection time CIP tomography could start with a reasonably good velocity model upon completion of the demultiple process.

Tailored acquisition and processing providing an enhanced subsurface image of the basin architecture, Exmouth Sub-basin, North West Shelf, Australia

2019 ◽  
Vol 59 (2) ◽  
pp. 886
Author(s):  
Alexander Karvelas ◽  
Bee Jik Lim ◽  
Lianping Zhang ◽  
Haryo Trihutomo ◽  
Oliver Schenk ◽  
...  
Keyword(s):  
Oil And Gas ◽  
Model Building ◽  
Waveform Inversion ◽  
Hydrocarbon Exploration ◽  
Surface Velocity ◽  
Seismic Survey ◽  
Image Point ◽  
Surface Model ◽  
Near Surface ◽  
North West

Hydrocarbon exploration has resulted in the discovery of a variety of oil and gas accumulations mainly in Upper Jurassic and Lower Cretaceous intervals. However, the distribution of the different petroleum system elements including Jurassic and Triassic intervals is poorly determined, but required for improved understanding of the complex charge history, as indicated by the variety of hydrocarbon types encountered in the basin. The new WesternGeco multiclient 3D seismic survey extends to the edges of the basin to give a comprehensive picture. Raw hydrophone data were delivered from the vessel as acquisition progressed to begin the near-surface model building. The model building consisted of two major stages: first, using full waveform inversion (FWI) to derive the near-surface velocity field; and, second, common image point (CIP) tomography to update the deeper section beyond the FWI illumination zone. As illustrated herein, various stages of processing and imaging provided a cleaner and crisper dataset across the record length, allowing (1) detailed picking of the events within the entire Mesozoic (Cretaceous–Triassic) section allowing key events to be interpreted and correlated across the area and (2) accurate investigation of the complexity of different aged fault networks and their relationships across the full Exmouth Sub-basin for the first time. In summary, this survey provides a detailed insight into the deeper basin architecture of the Exmouth Sub-basin. The seamless volume imaged to depth allows accurate mapping which is critical to unravel the complex evolutionary history in a basin with proven and significant remaining hydrocarbon potential.

High-resolution Radon preconditioning for full-waveform inversion of land seismic data

2017 ◽  
Vol 5 (4) ◽  
pp. SR23-SR33 ◽  
Author(s):  
Xin Cheng ◽  
Kun Jiao ◽  
Dong Sun ◽  
Zhen Xu ◽  
Denes Vigh ◽  
...  
Keyword(s):  
High Resolution ◽  
Seismic Data ◽  
Waveform Inversion ◽  
Low Frequency ◽  
Velocity Fields ◽  
Surface Velocity ◽  
Surface Model ◽  
Full Waveform Inversion ◽  
Near Surface ◽  
Full Waveform

Over the past decade, acoustic full-waveform inversion (FWI) has become one of the standard methods in the industry to construct high-resolution velocity fields from the seismic data acquired. While most of the successful applications are for marine acquisition data with rich low-frequency diving or postcritical waves at large offsets, the application of acoustic FWI on land data remains a challenging topic. Land acoustic FWI application faces many severe difficulties, such as the presence of strong elastic effects, large near-surface velocity contrast, and heterogeneous, topography variations, etc. In addition, it is well-known that low-frequency transmitted seismic energy is crucial for the success of FWI to overcome sensitivity to starting velocity fields; unfortunately, those are the parts of the data that suffer the most from a low signal-to-noise ratio (S/N) in land acquisition. We have developed an acoustic FWI application on a land data set from North Kuwait, and demonstrated our solutions to mitigate some of the challenges posed by land data. More specifically, we have developed a semblance-based high-resolution Radon (HR-Radon) inversion approach to enhance the S/N of the low-frequency part of the FWI input data and to ultimately improve the convergence of the land FWI workflow. To mitigate the impact of elastic effects, we included only the diving and postcritical early arrivals in the waveform inversion. Our results show that, with the aid of HR-Radon preconditioning and a carefully designed workflow, acoustic FWI has the ability to derive a reliable high-resolution near-surface model that could not be otherwise recovered through traditional tomographic methods.

An application of full-waveform inversion to land data using the pseudo-Hessian matrix

2016 ◽  
Vol 4 (4) ◽  
pp. T627-T635
Author(s):  
Yikang Zheng ◽  
Wei Zhang ◽  
Yibo Wang ◽  
Qingfeng Xue ◽  
Xu Chang
Keyword(s):  
Hessian Matrix ◽  
Waveform Inversion ◽  
Computational Cost ◽  
Velocity Model ◽  
Surface Velocity ◽  
Full Waveform Inversion ◽  
Data Set ◽  
Near Surface ◽  
Full Waveform ◽  
The Time Domain

Full-waveform inversion (FWI) is used to estimate the near-surface velocity field by minimizing the difference between synthetic and observed data iteratively. We apply this method to a data set collected on land. A multiscale strategy is used to overcome the local minima problem and the cycle-skipping phenomenon. Another obstacle in this application is the slow convergence rate. The inverse Hessian can enhance the poorly blurred gradient in FWI, but obtaining the full Hessian matrix needs intensive computation cost; thus, we have developed an efficient method aimed at the pseudo-Hessian in the time domain. The gradient in our FWI workflow is preconditioned with the obtained pseudo-Hessian and a synthetic example verifies its effectiveness in reducing computational cost. We then apply the workflow on the land data set, and the inverted velocity model is better resolved compared with traveltime tomography. The image and angle gathers we get from the inversion result indicate more detailed information of subsurface structures, which will contribute to the subsequent seismic interpretation.

Waveform tomography of field vibroseis data using an approximate 2D geometry leads to improved velocity models

Geophysics ◽  
2012 ◽  
Vol 77 (1) ◽  
pp. R33-R43 ◽  
Author(s):  
Brendan R. Smithyman ◽  
Ronald M. Clowes
Keyword(s):  
Waveform Inversion ◽  
Velocity Model ◽  
Surface Velocity ◽  
Time Shift ◽  
Full Waveform Inversion ◽  
Near Surface ◽  
Traveltime Tomography ◽  
Full Waveform ◽  
First Arrival ◽  
Waveform Tomography

Waveform tomography, a combination of traveltime tomography (or inversion) and waveform inversion, is applied to vibroseis first-arrival data to generate an interpretable model of P-wave velocity for a site in the Nechako Basin, south-central British Columbia, Canada. We use constrained 3D traveltime inversion followed by 2D full-waveform inversion to process long-offset (14.4 km) first-arrival refraction waveforms, resulting in a velocity model of significantly higher detail than a conventional refraction-statics model generated for a processing workflow. The crooked-line acquisition of the data set makes 2D full-waveform inversion difficult. Thus, a procedure that improves the tractability of waveform tomography processing of vibroseis data recorded on crooked roads is developed to generate a near-surface ([Formula: see text]) velocity model for the study area. The data waveforms are first static corrected using a time shift determined by 3D raytracing, which accounts for the crossline offsets produced by the crooked-line acquisition. The velocity model generated from waveform tomography exhibits substantial improvement when compared with a conventional refraction-statics model. It also shows improved resolution of sharp discontinuities and low-velocity regions when compared to the model from traveltime tomography alone, especially in regions where the geometry errors are moderate. Interpretation of the near-surface velocity model indicates possible subbasins in the Nechako Basin and delineates the Eocene volcanic rocks of the study area. This approach limits the ability of the full-waveform inversion to fit some propagation modes; however, the tractability of the inversion in the near-surface region is improved. This new development is especially useful in studies that do not warrant 3D seismic acquisition and processing.

Full-waveform inversion for full-wavefield imaging: Decades in the making

2021 ◽  
Vol 40 (5) ◽  
pp. 324-334
Author(s):  
Rongxin Huang ◽  
Zhigang Zhang ◽  
Zedong Wu ◽  
Zhiyuan Wei ◽  
Jiawei Mei ◽  
...  
Keyword(s):  
Model Building ◽  
Seismic Imaging ◽  
Structural Information ◽  
Waveform Inversion ◽  
Velocity Model ◽  
Data Sets ◽  
Full Waveform Inversion ◽  
Data Types ◽  
Velocity Models ◽  
Full Waveform

Seismic imaging using full-wavefield data that includes primary reflections, transmitted waves, and their multiples has been the holy grail for generations of geophysicists. To be able to use the full-wavefield data effectively requires a forward-modeling process to generate full-wavefield data, an inversion scheme to minimize the difference between modeled and recorded data, and, more importantly, an accurate velocity model to correctly propagate and collapse energy of different wave modes. All of these elements have been embedded in the framework of full-waveform inversion (FWI) since it was proposed three decades ago. However, for a long time, the application of FWI did not find its way into the domain of full-wavefield imaging, mostly owing to the lack of data sets with good constraints to ensure the convergence of inversion, the required compute power to handle large data sets and extend the inversion frequency to the bandwidth needed for imaging, and, most significantly, stable FWI algorithms that could work with different data types in different geologic settings. Recently, with the advancement of high-performance computing and progress in FWI algorithms at tackling issues such as cycle skipping and amplitude mismatch, FWI has found success using different data types in a variety of geologic settings, providing some of the most accurate velocity models for generating significantly improved migration images. Here, we take a step further to modify the FWI workflow to output the subsurface image or reflectivity directly, potentially eliminating the need to go through the time-consuming conventional seismic imaging process that involves preprocessing, velocity model building, and migration. Compared with a conventional migration image, the reflectivity image directly output from FWI often provides additional structural information with better illumination and higher signal-to-noise ratio naturally as a result of many iterations of least-squares fitting of the full-wavefield data.

Assisting salt model building with reflection full-waveform inversion

2019 ◽  
Vol 7 (2) ◽  
pp. SB43-SB52 ◽  
Author(s):  
Adriano Gomes ◽  
Joe Peterson ◽  
Serife Bitlis ◽  
Chengliang Fan ◽  
Robert Buehring
Keyword(s):  
Model Building ◽  
Waveform Inversion ◽  
Low Frequency ◽  
Velocity Model ◽  
Full Waveform Inversion ◽  
Reflection Data ◽  
Full Waveform ◽  
Velocity Model Building ◽  
Wave Limit ◽  
Rabbit Ears

Inverting for salt geometry using full-waveform inversion (FWI) is a challenging task, mostly due to the lack of extremely low-frequency signal in the seismic data, the limited penetration depth of diving waves using typical acquisition offsets, and the difficulty in correctly modeling the amplitude (and kinematics) of reflection events associated with the salt boundary. However, recent advances in reflection FWI (RFWI) have allowed it to use deep reflection data, beyond the diving-wave limit, by extracting the tomographic term of the FWI reflection update, the so-called rabbit ears. Though lacking the resolution to fully resolve salt geometry, we can use RFWI updates as a guide for refinements in the salt interpretation, adding a partially data-driven element to salt velocity model building. In addition, we can use RFWI to update sediment velocities in complex regions surrounding salt, where ray-based approaches typically struggle. In reality, separating the effects of sediment velocity errors from salt geometry errors is not straightforward in many locations. Therefore, iterations of RFWI plus salt scenario tests may be necessary. Although it is still not the fully automatic method that has been envisioned for FWI, this combined approach can bring significant improvement to the subsalt image, as we examine on field data examples from the Gulf of Mexico.

Sign in / Sign up

Export Citation Format

Share Document