Prediction of mobile water in a tight gas sandstone reservoir using NMR and fractional flow model

2014 ◽  
Vol 54 (2) ◽  
pp. 1
Author(s):  
Maria Anantawati ◽  
Suryakant Bulgauda
Keyword(s):  
Steady State ◽  
Relative Permeability ◽  
Flow Model ◽  
Bound Water ◽  
Free Water ◽  
Development Project ◽  
Asia Pacific ◽  
Fractional Flow ◽  
Reservoir Properties ◽  
Mobile Water

One of the objectives of petrophysical interpretation is the estimation of the respective volumes of formation fluids. With traditional interpretation using conventional openhole logs it is only possible to determine the total amount of water. The challenge is to determine the volumes of bound water (clay-bound and capillary-bound) and free water. At the moment, NMR is the only measurement that can help distinguish the volumes of each water component (clay-bound, capillary-bound and mobile), using cut-offs on T2 (transverse relaxation time). However NMR interpretation also requires information on reservoir properties. Alternatively, steady-state relative permeability and fractional flow of water can be used to determine the potential of mobile water. The study area, located in the Cooper Basin, South Australia, is the target of a planned gas development project in the Patchawarra formation. It comprises multiple stacked fluvial sands which are heterogeneous, tight and of low deliverability. The sands are completed with multi-stage pin-point fracturing as a key enabling technology for the area. A comprehensive set of data, including conventional logs, cores and NMR logs, were acquired. Routine and special core analysis were performed, including NMR, electrical properties, centrifuge capillary pressure, high-pressure mercury injection, and full curve steady state relative permeability. A fractional flow model was built based on core and NMR data to determine potential mobile water and the results compared with production logs. This paper (SPE 165766) was prepared for presentation at the SPE Asia Pacific Oil & Gas Conference and Exhibition, held in Jakarta, Indonesia, from 22–24 October 2013.

Assessment of Bone Quality Associated With Loosely and Tightly Bound Water

2010 ◽  
Author(s):  
Qingwen Ni ◽  
Naniel P. Nicolella
Keyword(s):  
Bone Strength ◽  
Bone Quality ◽  
Water Distribution ◽  
Mechanical Test ◽  
Bound Water ◽  
Free Water ◽  
Water Molecules ◽  
Surface Charges ◽  
Mobile Water ◽  
Age Related

Previous studies have shown that the age-related increase in bone porosity results a decrease in bone strength, and porosity is related to the volume of mobile water in the pores. In addition, since water is also bound to collagen and mineral, changes in the amount of bound water will potentially affect the bone strength. It is known that the removal of the loosely bound water (via hydrogen bonding) requires less energy than the water molecules trapped inside collagen molecules, which in turn requires similar or less energy than water molecules bound to the surface charges of mineral apatite (more ionic in nature). Also, water that is imbedded in the lattice of hydroxyapatite (more covalent in nature) requires the highest energy to dislodge. However, there is no traditional method that can determine mobile and bound water, further for loosely and tightly bound ware accurately, non-destructively and non-invasively. Here, we propose that by using NMR Car-Purcell-Meiboom-Gill (CPMG) spin-spin relaxation measurement to determine the mobile water, and the NMR inversion T2-FID spectrum derived from NMR free induction decay (FID) measurements for estimating the bound and free water distribution. Furthermore, after comparison of the total water lost (weighing method) within tissue by using drying (free dry) on the air to the total mobile water lost measured by NMR CPMG method, then, the total loosely bound water lost can be estimated. Following this, the mechanical test will be used to evaluate the bone quality related to the tightly and loosely bound water within bone. This information can be used to further assessment of bone quality.

Intercept Method—A Novel Technique To Correct Steady-State Relative Permeability Data for Capillary End Effects

2015 ◽  
Vol 19 (02) ◽  
pp. 316-330 ◽  
Author(s):  
Robin Gupta ◽  
Daniel R. Maloney
Keyword(s):  
Steady State ◽  
Relative Permeability ◽  
Data Interpretation ◽  
End Effect ◽  
Fractional Flow ◽  
End Effects ◽  
Flow Rates ◽  
Pressure Drops ◽  
State Tests ◽  
State Measurement

Summary In laboratory measurements of relative permeability, capillary discontinuities at sample ends give rise to capillary end effects (CEEs). End effects affect fluid flow and retention. If end-effect artifacts are not minimized by test design and data interpretation, relative permeability results may be significantly erroneous. This is a well-known issue in unsteady-state tests, but even steady-state relative permeability results are influenced by end-effect artifacts. This work describes the intercept method, a novel modified steady-state approach in which corrections for end-effect artifacts are applied as data are measured. The intercept method requires running a steady-state relative permeability test with several different flow rates for each fractional flow. Obtaining multiple (three or four) sets of rates (Q), pressure drops (ΔP), and saturation data allows for assessment of CEE artifacts. With Darcy flow, a plot of pressure drop vs. total flow rate is typically linear. A nonzero intercept or offset is an end-effect artifact. To correct for the effect, the offset is subtracted from measured pressure drops. Corrected pressure drops are used in permeability calculations. The set of saturations from measurements at the target fractional flow is used to calculate a corrected final saturation. Because corrections for end effects are made during the test rather than after the test is complete, any discrepancies can be resolved by additional measurements before moving on to the next fractional flow. Rates are then adjusted to yield the next target fractional-flow condition, and the same protocol is repeated for each subsequent steady-state measurement. The method is validated by theory and is easy to apply.

scholarly journals Experimental investigation of the displacement flow mechanism and oil recovery in primary polymer flood operations

2021 ◽  
Vol 3 (5) ◽  
Author(s):  
Ruissein Mahon ◽  
Gbenga Oluyemi ◽  
Babs Oyeneyin ◽  
Yakubu Balogun
Keyword(s):  
Relative Permeability ◽  
Oil Recovery ◽  
Polymer Flooding ◽  
Mobility Control ◽  
List Type ◽  
Motor Oil ◽  
Flow Mechanism ◽  
Fractional Flow ◽  
Recovery Method ◽  
Polymer Flood

Abstract Polymer flooding is a mature chemical enhanced oil recovery method employed in oilfields at pilot testing and field scales. Although results from these applications empirically demonstrate the higher displacement efficiency of polymer flooding over waterflooding operations, the fact remains that not all the oil will be recovered. Thus, continued research attention is needed to further understand the displacement flow mechanism of the immiscible process and the rock–fluid interaction propagated by the multiphase flow during polymer flooding operations. In this study, displacement sequence experiments were conducted to investigate the viscosifying effect of polymer solutions on oil recovery in sandpack systems. The history matching technique was employed to estimate relative permeability, fractional flow and saturation profile through the implementation of a Corey-type function. Experimental results showed that in the case of the motor oil being the displaced fluid, the XG 2500 ppm polymer achieved a 47.0% increase in oil recovery compared with the waterflood case, while the XG 1000 ppm polymer achieved a 38.6% increase in oil recovery compared with the waterflood case. Testing with the motor oil being the displaced fluid, the viscosity ratio was 136 for the waterflood case, 18 for the polymer flood case with XG 1000 ppm polymer and 9 for the polymer flood case with XG 2500 ppm polymer. Findings also revealed that for the waterflood cases, the porous media exhibited oil-wet characteristics, while the polymer flood cases demonstrated water-wet characteristics. This paper provides theoretical support for the application of polymer to improve oil recovery by providing insights into the mechanism behind oil displacement. Graphic abstract Highlights The difference in shape of relative permeability curves are indicative of the effect of mobility control of each polymer concentration. The water-oil systems exhibited oil-wet characteristics, while the polymer-oil systems demonstrated water-wet characteristics. A large contrast in displacing and displaced fluid viscosities led to viscous fingering and early water breakthrough.

Determine the Moisture Distribution in Sewage Sludge by Drying Differential

2014 ◽  
Vol 665 ◽  
pp. 404-407 ◽  
Author(s):  
Wan Yu ◽  
Pei Sheng Li
Keyword(s):  
Sewage Sludge ◽  
Interstitial Water ◽  
Bound Water ◽  
Free Water ◽  
High Accuracy ◽  
Moisture Distribution ◽  
Municipal Sewage ◽  
Municipal Sewage Sludge ◽  
Hot Air ◽  
Critical Water Content

Moisture distribution in sewage sludge was considered as the essential of thermal drying. Some methods were given in literatures to test the moisture distribution, but there was no standard method to determine the critical water content between different kinds of water. The municipal sewage sludge was dried by hot air in this work. Based on the drying curve, the derivative of drying rate with respect to dry basis moisture content was brought out to analyze the moisture distribution in sewage sludge. Results show that this method can easily determine the free water, interstitial water, surface water and bound water with a high accuracy. The present work can provide new insight to determine the moisture distribution in sewage sludge, which was still lacking in the literatures.

Sign in / Sign up

Export Citation Format

Share Document