scholarly journals Biaxial compression mechanical properties of HTPB propellant under dynamic loading

AIP Advances ◽  
2022 ◽  
Vol 12 (1) ◽  
pp. 015306
Author(s):  
Tingjing Geng ◽  
Hongfu Qiang ◽  
Zhejun Wang ◽  
Xueren Wang ◽  
Chunguo Yue
Keyword(s):  
Mechanical Properties ◽  
Dynamic Loading ◽  
Biaxial Compression ◽  
Htpb Propellant

scholarly journals Experimental Investigation into Corrosion Effect on Mechanical Properties of High Strength Steel Bars under Dynamic Loadings

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Hui Chen ◽  
Jinjin Zhang ◽  
Jin Yang ◽  
Feilong Ye
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Dynamic Loading ◽  
High Strength Steel ◽  
High Strength ◽  
Tensile Tests ◽  
Reinforcing Steel ◽  
Test Results ◽  
Cross Sectional ◽  
Steel Bars

The tensile behaviors of corroded steel bars are important in the capacity evaluation of corroded reinforced concrete structures. The present paper studies the mechanical behavior of the corroded high strength reinforcing steel bars under static and dynamic loading. High strength reinforcing steel bars were corroded by using accelerated corrosion methods and the tensile tests were carried out under different strain rates. The results showed that the mechanical properties of corroded high strength steel bars were strain rate dependent, and the strain rate effect decreased with the increase of corrosion degree. The decreased nominal yield and ultimate strengths were mainly caused by the reduction of cross-sectional areas, and the decreased ultimate deformation and the shortened yield plateau resulted from the intensified stress concentration at the nonuniform reduction. Based on the test results, reduction factors were proposed to relate the tensile behaviors with the corrosion degree and strain rate for corroded bars. A modified Johnson-Cook strength model of corroded high strength steel bars under dynamic loading was proposed by taking into account the influence of corrosion degree. Comparison between the model and test results showed that proposed model properly describes the dynamic response of the corroded high strength rebars.

Influence of cyclic load input on the mechanical properties of a sensitive soil from Orleans, Ontario

1980 ◽  
Vol 17 (4) ◽  
pp. 498-508 ◽  
Author(s):  
R. N. Yong ◽  
D. Taplin ◽  
G. Wiseman
Keyword(s):  
Mechanical Properties ◽  
Laboratory Test ◽  
Dynamic Loading ◽  
Cyclic Strain ◽  
Peak Stress ◽  
Confining Pressure ◽  
Constant Load ◽  
Deviatoric Stress ◽  
General Terms ◽  
Stress Levels

The importance of disturbance and remoulding to the alteration of mechanical properties of sensitive soils has been well documented in the geotechnical literature both in terms of laboratory and field behaviours. Man-made transient dynamic input such as dynamite blasting, heavy vehicles, and train movement have been suspected of being capable of causing a reduction in the in situ strength parameters of sensitive clays. A laboratory test program was undertaken to determine whether dynamic loading at peak stress levels below normal failure strength caused similar changes in the mechanical properties, and specifically to quantify the phenomena.In order to simulate highly overconsolidated conditions most of the tests were carried out under conditions of no confining pressure, although supplemental data were obtained from consolidated undrained tests. Some of the variables examined in this program were confining pressure, mean deviatoric stress, cyclic deviatoric stress, cyclic strain, number of applications, frequency, and reference strength. In order to compare the effect of dynamic input with the long-term creep phenomena, a simultaneous constant load program was undertaken.In general terms, the study indicates that under the prestated laboratory test conditions no major reduction in peak strength was found under dynamic loading, and that failure would occur at comparative stress levels under dead-load conditions, but required a greater time. In addition, examination of the sample after failure revealed that any remoulding of the sample appeared to be restricted to the area adjacent to the shear zone.

Mechanical Properties of Newly Developed Mg-Alloys AMX602 AND AZXE7111 under Quasi-Static and Dynamic Loading

2012 ◽  
pp. 371-375
Author(s):  
J. Shen ◽  
K. Kondoh ◽  
T.L. Jones ◽  
S.N. Mathaudhu ◽  
L.J. Kecskes ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Dynamic Loading ◽  
Mg Alloys ◽  
Static And Dynamic Loading

scholarly journals Detailed Study on the Mechanical Properties and Activation Energy of Natural Rubber/Chloroprene Rubber Blends during Aging Processes

2020 ◽  
Vol 2020 ◽  
pp. 1-7
Author(s):  
Quang Nguyen Trong ◽  
Hung Dang Viet ◽  
Linh Nguyen Pham Duy ◽  
Chuong Bui ◽  
Duong Duc La
Keyword(s):  
Mechanical Properties ◽  
Natural Rubber ◽  
Dynamic Loading ◽  
Dynamic Properties ◽  
Activation Energies ◽  
Rubber Matrix ◽  
Static Properties ◽  
Rubber Blends ◽  
Aging Conditions ◽  
Mechanical Aging

Selection of a suitable thermal aging process could render desirable mechanical properties of the rubbers or blended rubbers. In this work, the effect of the aging processes on the mechanical properties and activation energies of natural rubbers (NR) and NR/chloroprene rubbers (CR) blends with low CR contents (5–10%) was investigated. Three aging processes including heat aging (at 110°C for 22 hours), mechanical aging (under dynamic loading to 140% strain for 16000 cycles), and complex aging (heat and mechanical aging) were studied. The results revealed that the compatibility of CR in natural rubber matrix had a significant effect on the dynamic properties of the blended rubber and negligible effect on the static properties. The changes in activation energies of the blended rubber during aging processes were calculated using Arrhenius relation. The calculated changes (ΔUc, ΔUd, and ΔUT) in activation energies were consistent with the results of mechanical properties of the blended rubber. Interestingly, the change in activation energies using complex aging conditions (ΔUc) was mostly equal to the total changes in activation energies calculated separately from heat aging (ΔUT) and mechanical aging (ΔUd) conditions. This indicates that, in complex aging conditions, the heat and dynamic loading factors act independently on the properties of the blended rubber.

Study on the Relationship between Microscopic Structure and Mechanical Properties of HTPB Propellant

2010 ◽  
Vol 152-153 ◽  
pp. 1151-1155 ◽  
Author(s):  
Xu Chang Li ◽  
Jian Jiao ◽  
Jun Yan Yao ◽  
Liang Wang
Keyword(s):  
Mechanical Properties ◽  
Mechanical Property ◽  
Cross Section ◽  
Structural Integrity ◽  
Solid Particles ◽  
Microscopic Structure ◽  
Structure State ◽  
Htpb Propellant ◽  
The Relationship ◽  
Bond Effect

By means of a tensile instrument and SEM, the mechanical property parameters of HTPB propellant test samples with different formulas were tested, and their microscopic fracture cross section patterns were observed. Take advantage of these testing results, the relationship between microscopic structure and mechanical properties of HTPB propellant was studied. The results show that the mechanical properties of a propellant are closely related to its microscpic structure state. The structural integrity of propellant is mainly influenced by the bond effect of the interface between binder and solid particles, solid particle’s shape, size and its distribution, the content of binder matrix, etc. These factors have important effects on the mechanical properties of propellant.

Sign in / Sign up

Export Citation Format

Share Document