scholarly journals Ion beam etching dependence of spin–orbit torque memory devices with switching current densities reduced by Hf interlayers

APL Materials ◽  
2021 ◽  
Vol 9 (9) ◽  
pp. 091101
Author(s):  
Haowen Ren ◽  
Shih-Yu Wu ◽  
Jonathan Z. Sun ◽  
Eric E. Fullerton
Keyword(s):  
Ion Beam ◽  
Memory Devices ◽  
Spin Orbit ◽  
Ion Beam Etching ◽  
Switching Current ◽  
Current Densities

Abstract: Ion beam etching equipment for production of bubble memory devices

1979 ◽  
Vol 50 (B3) ◽  
pp. 2299-2299 ◽  
Author(s):  
G. W. Monk ◽  
G. R. Thompson
Keyword(s):  
Ion Beam ◽  
Memory Devices ◽  
Ion Beam Etching

Ultrastructural Features of Normal and Diseased Hair Revealed by Ion Beam Etching and Freeze Fracture

1975 ◽  
Vol 33 ◽  
pp. 358-359
Author(s):  
M. Spector ◽  
A. C. Brown
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Ectodermal Dysplasia ◽  
Ion Beam ◽  
Freeze Fracture ◽  
Ion Current ◽  
Ion Beam Etching ◽  
Pili Torti ◽  
Argon Ion ◽  
Scanning Electron

Ion beam etching and freeze fracture techniques were utilized in conjunction with scanning electron microscopy to study the ultrastructure of normal and diseased human hair. Topographical differences in the cuticular scale of normal and diseased hair were demonstrated in previous scanning electron microscope studies. In the present study, ion beam etching and freeze fracture techniques were utilized to reveal subsurface ultrastructural features of the cuticle and cortex.Samples of normal and diseased hair including monilethrix, pili torti, pili annulati, and hidrotic ectodermal dysplasia were cut from areas near the base of the hair. In preparation for ion beam etching, untreated hairs were mounted on conducting tape on a conducting silicon substrate. The hairs were ion beam etched by an 18 ky argon ion beam (5μA ion current) from an ETEC ion beam etching device. The ion beam was oriented perpendicular to the substrate. The specimen remained stationary in the beam for exposures of 6 to 8 minutes.

Chemical Precursors for GaAs Etching with low Energy ion Beams: Chlorine adsorption on GaAs(100)

1991 ◽  
Vol 223 ◽  
Author(s):  
Richard B. Jackman ◽  
Glenn C. Tyrrell ◽  
Duncan Marshall ◽  
Catherine L. French ◽  
John S. Foord
Keyword(s):  
Ion Beam ◽  
Ion Beams ◽  
Low Energy ◽  
Ion Beam Etching ◽  
Chlorine Adsorption

ABSTRACTThis paper addresses the issue of chlorine adsorption on GaAs(100) with respect to the mechanisms of thermal and ion-enhanced etching. The use of halogenated precursors eg. dichloroethane is also discussed in regard to chemically assisted ion beam etching (CAIBE).

High-Throughput, Site-Specific Sample Prep of Ultra-Thin TEM Lamella for Process Metrology and Failure Analysis

2012 ◽  
Author(s):  
Roger Alvis ◽  
Jeff Blackwood ◽  
Sang-Hoon Lee ◽  
Matthew Bray
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Process Monitoring ◽  
High Throughput ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Memory Devices ◽  
Site Specific ◽  
Critical Dimensions ◽  
Tem Lamella

Abstract Semiconductor devices with critical dimensions less than 20nm are now being manufactured in volume. A challenge facing the failure analysis and process-monitoring community is two-fold. The first challenge of TEM sample prep of such small devices is that the basic need to end-point on a feature-of-interest pushes the imaging limit of the instrument being used to prepare the lamella. The second challenge posed by advanced devices is to prepare an artifact-free lamella from non-planar devices such as finFETs as well as from structures incorporating ‘non-traditional’ materials. These challenges are presently overcome in many advanced logic and memory devices in the focused ion beam-based TEM sample preparation processes by inverting the specimen prior to thinning to electron transparency. This paper reports a highthroughput method for the routine preparation of artifact-free TEM lamella of 20nm thickness, or less.

TEM Sample Preparation by Single-Sided Low-Energy Ion Beam Etching

2011 ◽  
Author(s):  
Liew Kaeng Nan ◽  
Lee Meng Lung
Keyword(s):  
Sample Preparation ◽  
Semiconductor Device ◽  
Ion Beam ◽  
Critical Dimension ◽  
Low Energy ◽  
Ex Situ ◽  
Good Image Quality ◽  
Ion Beam Etching ◽  
Device Structures ◽  
Common Technique

Abstract Conventional FIB ex-situ lift-out is the most common technique for TEM sample preparation. However, the scaling of semiconductor device structures poses great challenge to the method since the critical dimension of device becomes smaller than normal TEM sample thickness. In this paper, a technique combining 30 keV FIB milling and 3 keV ion beam etching is introduced to prepare the TEM specimen. It can be used by existing FIBs that are not equipped with low-energy ion beam. By this method, the overlapping pattern can be eliminated while maintaining good image quality.

Failure Analysis Strategies for Multistacked Memory Devices with TSV Interconnects

2015 ◽  
Author(s):  
Frank Altmann ◽  
Christian Grosse ◽  
Falk Naumann ◽  
Jens Beyersdorfer ◽  
Tony Veches
Keyword(s):  
Failure Analysis ◽  
Focused Ion Beam ◽  
Failure Modes ◽  
Ion Beam ◽  
Memory Devices ◽  
Metallographic Cross Section ◽  
Electron Beam Induced Current ◽  
Thermal Simulations ◽  
Lock In ◽  
Non Destructive

Abstract In this paper we will demonstrate new approaches for failure analysis of memory devices with multiple stacked dies and TSV interconnects. Therefore, TSV specific failure modes are studied on daisy chain test samples. Two analysis flows for defect localization implementing Electron Beam Induced Current (EBAC) imaging and Lock-in-Thermography (LIT) as well as adapted Focused Ion Beam (FIB) preparation and defect characterization by electron microscopy will be discussed. The most challenging failure mode is an electrical short at the TSV sidewall isolation with sub-micrometer dimensions. It is shown that the leakage path to a certain TSV within the stack can firstly be located by applying LIT to a metallographic cross section and secondly pinpointing by FIB/SEM cross-sectioning. In order to evaluate the potential of non-destructive determination of the lateral defect position, as well as the defect depth from only one LIT measurement, 2D thermal simulations of TSV stacks with artificial leakages are performed calculating the phase shift values per die level.

Sign in / Sign up

Export Citation Format

Share Document