scholarly journals The influence of gas volume fractions on deformation and volumetric efficiency of twin-screw multiphase pump based on fluid–thermal–structure coupling numerical calculation

2021 ◽  
Vol 33 (7) ◽  
pp. 075103
Author(s):  
Xuejing Zhang ◽  
Junhu Yang ◽  
Chong Ma ◽  
Wei Han ◽  
Deqiang Wei ◽  
...  
Keyword(s):  
Numerical Calculation ◽  
Thermal Structure ◽  
Volumetric Efficiency ◽  
Multiphase Pump ◽  
Volume Fractions ◽  
Twin Screw ◽  
Gas Volume

Evaluation of a Twin Screw Pump for Use in High Gas Volume Fraction Flows

2012 ◽  
Author(s):  
Gerald L. Morrison ◽  
Abhay Patil ◽  
Daniel Cihak
Keyword(s):  
Volume Fraction ◽  
Pressure Rise ◽  
Maintenance Cost ◽  
Pure Liquid ◽  
Pump Efficiency ◽  
Screw Pump ◽  
Multiphase Pump ◽  
Volume Fractions ◽  
Twin Screw ◽  
Gas Volume

The use of multiphase pumps on gas and oil wells which have Gas Volume Fractions (GVF) between 50 and 100% have been shown to have practical applications[1]. A single multiphase pump can replace a separation system, gas compressor, and liquid pump. This can significantly reduce installation cost, maintenance cost, and the space occupied by the system. By reducing the well head pressure, additional production can also be obtained. This work investigates the ability of a 200 hp, 635 gpm twin screw pump designed for use as a multiphase pump to operate over a range of gas volume fractions, inlet pressure, pressure rise, and operating speed. GVF’s from 50% to 100% are considered with inlet pressures from 15 to 100 psig. The pump pressure rise is varied from 50 to 300 psig for operating speeds of 900, 1350, and 1800 rpm. The working fluids for this evaluation are air and water. Each are separately measured prior to injection into the pump inlet. Electrical power consumed along with pressure and temperature measurements across the pump allow the evaluation of pump efficiency, hydraulic performance, volumetric efficiency, and effectiveness (reduction in hydraulic efficiency from pure liquid performance).

Leakage Loss Study of a Synchronal Rotary Multiphase Pump With a Full Range of Inlet Gas Volume Fractions

2016 ◽  
Vol 138 (7) ◽  
Author(s):  
Xu Yang ◽  
Yao Qin ◽  
Zongchang Qu
Keyword(s):  
Flow Rate ◽  
Flow Model ◽  
Full Range ◽  
Volumetric Flow Rate ◽  
Radial Clearance ◽  
Leakage Flow ◽  
Leakage Loss ◽  
Multiphase Pump ◽  
Volume Fractions ◽  
Gas Volume

The working performance of the synchronal rotary multiphase pump (SRMP), alike other types of positive-displacement multiphase pumps, is strongly affected by leakage loss. In this paper, the leakage loss in the SRMP with a full range of inlet gas volume fractions (GVFs) was theoretically and experimentally investigated. The leakage flows in the SRMP were modeled as the one-dimensional gas–liquid flows through narrow gaps. Two types of leakage flow models, homogeneous leakage flow model (HLFM) and separated leakage flow model (SLFM), were developed. The experimental work was conducted to measure the volumetric flow rate of the SRMP using the mixtures of air and N32 oil as working fluids under various inlet GVFs and differential pressures. Comparisons between the simulated and experimental pump flow rates showed that both the accuracies of the HLFM and SLFM related to the inlet GVF. In addition to the differential pressure, the leakage loss of the SRMP was affected by the inlet GVF. The leakage flow rate increased with the inlet GVF due to the changes in physical properties of the gas–liquid leakage flow. Parametric analysis showed that leakage loss in the SRMP can be effectively reduced by reducing the rotor radial clearance without much effect on its mechanical efficiency, whereas the optimum geometric parameters of the rotor and cylinder must be calculated by means of the optimization study with consideration of both the leakage loss and friction loss.

Leakage Analysis of a Synchronal Rotary Multiphase Pump

2012 ◽  
Vol 562-564 ◽  
pp. 635-638
Author(s):  
Xu Yang ◽  
Zong Chang Qu ◽  
Yu Yuan Wu
Keyword(s):  
Pressure Difference ◽  
Volume Fraction ◽  
Volumetric Efficiency ◽  
Leakage Loss ◽  
Two Phase ◽  
Multiphase Pump ◽  
Leakage Flows ◽  
Positive Displacement ◽  
Gas Volume Fraction ◽  
Gas Volume

A novel positive-displacement multiphase pump named synchronal rotary multiphase pump (SRMP) was introduced. The two-phase leakage flows through the various leakage clearances in the SRMP were theoretically analyzed and formulated. Calculations on the leakage loss of a SRMP prototype were performed. The results show that the leakage loss is mainly produced by the leakage through the radical clearance between the rotor and cylinder. The SRMP presents a lower volumetric efficiency at a higher pressure difference. The leakage loss increases rapidly with the increase of the gas volume fraction of the two-phase working fluids.

Numerical investigation on screw rotor deformation and influence on volumetric efficiency of the twin-screw multiphase pump

2017 ◽  
Vol 111 ◽  
pp. 1111-1118 ◽  
Author(s):  
Xiang Yin ◽  
Feng Cao ◽  
Shengchen Pan ◽  
Yulong Song ◽  
Jiyou Fei ◽  
...  
Keyword(s):  
Numerical Investigation ◽  
Volumetric Efficiency ◽  
Multiphase Pump ◽  
Twin Screw ◽  
Screw Rotor

scholarly journals Proposal of a stage-by-stage design method and its application on a multi-stage multiphase pump based on numerical simulations

2021 ◽  
Vol 13 (1) ◽  
pp. 168781402098731
Author(s):  
Yi Shi ◽  
Hongwu Zhu
Keyword(s):  
Volume Fraction ◽  
Design Method ◽  
Oil Field ◽  
Stage Design ◽  
Multiphase Pump ◽  
Flow Parameters ◽  
Multi Stage ◽  
Comparison Results ◽  
Third Stage ◽  
Gas Volume

Rotodynamic multiphase pumps are usually equipped with many compression units to provide sufficient boosting pressure for the transportation of production fluid in gas oil field. It is a challenge to maintain pump performance while flow parameters in each stage vary due to the compressibility of gas-liquid phase. In this article, a stage-by-stage design method is proposed to improve the boosting capability of a multiphase pump. Variations of flow parameters in each stage are investigated based on computational fluid dynamics (CFD) numerical simulation. Available methods to determinate main impeller geometry parameters of impeller are discussed. The stage-by-stage design method is applied on a five-stage multiphase pump when the inlet gas volume fraction (GVF) are 30% and 50% separately. The second stage is modified base on its corresponding inlet flow parameters when inlet GVF is 30% while the second and third stage are modified when inlet GVF is 50%. Flow parameters, pressure distribution and velocity distribution are compared between the original pump and modified pump. Differential pressure of the modified pump increases by 53.72 kPa and 58.57 kPa respectively when inlet GVFs are 30% and 50%. The feasibility of the stage-by-stage design method is verified through the comparison results.

scholarly journals Effect of the Gas Volume Fraction on the Pressure Load of the Multiphase Pump Blade

Processes ◽  
2021 ◽  
Vol 9 (4) ◽  
pp. 650
Author(s):  
Guangtai Shi ◽  
Dandan Yan ◽  
Xiaobing Liu ◽  
Yexiang Xiao ◽  
Zekui Shu
Keyword(s):  
Flow Rate ◽  
Static Pressure ◽  
Volume Fraction ◽  
Pump Impeller ◽  
Impeller Blade ◽  
Multiphase Pump ◽  
Pressure Load ◽  
Gas Volume Fraction ◽  
Power Capability ◽  
Gas Volume

The gas volume fraction (GVF) often changes from time to time in a multiphase pump, causing the power capability of the pump to be increasingly affected. In the purpose of revealing the pressure load characteristics of the multiphase pump impeller blade with the gas-liquid two-phase case, firstly, a numerical simulation which uses the SST k-ω turbulence model is verified with an experiment. Then, the computational fluid dynamics (CFD) software is employed to investigate the variation characteristics of static pressure and pressure load of the multiphase pump impeller blade under the diverse inlet gas volume fractions (IGVFs) and flow rates. The results show that the effect of IGVF on the head and hydraulic efficiency at a small flow rate is obviously less than that at design and large flow rates. The static pressure on the blade pressure side (PS) is scarcely affected by the IGVF. However, the IGVF has an evident effect on the static pressure on the impeller blade suction side (SS). Moreover, the pump power capability is descended by degrees as the IGVF increases, and it is also descended with the increase of the flow rate at the impeller inlet. Simultaneously, under the same IGVF, with the increase of the flow rate, the peak value of the pressure load begins to gradually move toward the outlet and its value from hub to shroud is increased. The research results have important theoretical significance for improving the power capability of the multiphase pump impeller.

Sign in / Sign up

Export Citation Format

Share Document