scholarly journals Publisher's Note: “A planar microwave resonator with odd resonance for calibration in permanent moisture sensing applications” [Appl. Phys Lett. 118, 144104 (2021)]

2021 ◽  
Vol 118 (20) ◽  
pp. 209902
Author(s):  
S. S. Olokede ◽  
M. L. Neyestanak ◽  
Marco Chu ◽  
M. Daneshmand ◽  
H. E. Naguib
Keyword(s):  
Microwave Resonator ◽  
Sensing Applications ◽  
Moisture Sensing

A planar microwave resonator with odd resonance for calibration in permanent moisture sensing applications

2021 ◽  
Vol 118 (14) ◽  
pp. 144104
Author(s):  
S. S. Olokede ◽  
M. L. Neyestana ◽  
Marco Chu ◽  
M. Daneshmand ◽  
H. E. Naguib
Keyword(s):  
Microwave Resonator ◽  
Sensing Applications ◽  
Moisture Sensing

Investigating the Potential of a PEDOT:PSS Organic Microwave Resonator for Gas Sensing Applications

2021 ◽  
Author(s):  
Maryam Moradpour ◽  
Mandeep C. Jain ◽  
Nicolas R. Tanguy ◽  
Mohammad H. Zarifi
Keyword(s):  
Gas Sensing ◽  
Microwave Resonator ◽  
Sensing Applications

Locally Strong-Coupled Microwave Resonator Using PEMC Boundary for Distant Sensing Applications

2019 ◽  
Vol 67 (10) ◽  
pp. 4130-4139 ◽  
Author(s):  
Mehdi Nosrati ◽  
Zahra Abbasi ◽  
Masoud Baghelani ◽  
Sharmistha Bhadra ◽  
Mojgan Daneshmand
Keyword(s):  
Microwave Resonator ◽  
Sensing Applications

Facile Preparation of Carbon-Nanotube-based 3-Dimensional Transparent Conducting Networks for Flexible Noncontact Sensing Device

MRS Advances ◽  
2016 ◽  
Vol 1 (52) ◽  
pp. 3533-3538
Author(s):  
Yanlong Tai ◽  
Gilles Lubineau
Keyword(s):  
Carbon Nanotube ◽  
Indium Tin Oxide ◽  
High Performance ◽  
Visible Range ◽  
3 Dimensional ◽  
Conductive Films ◽  
Sensing Applications ◽  
Conducting Networks ◽  
Controllable Fabrication ◽  
Moisture Sensing

ABSTRACTHere, we report the controllable fabrication of transparent conductive films (TCFs) for moisture-sensing applications based on heating-rate-triggered, 3-dimensional porous conducting networks of single-walled carbon nanotube (SWCNT)/poly(3,4-ethylenedioxythiophene)-polystyrene sulfonate (PEDOT:PSS). How baking conditions influence the self-assembled microstructure of the TCFs is discussed. The sensor presents high-performance properties, including a reasonable sheet resistance (2.1 kohm/sq), a high visible-range transmittance (> 69 %, PET = 90 %), and good stability when subjected to cyclic loading (> 1000 cycles, better than indium tin oxide film) during processing. Moreover, the benefits of these kinds of TCFs were verified through a fully transparent, highly sensitive, rapid response, noncontact moisture-sensing device (5×5 sensing pixels).

scholarly journals Reference-Incorporating Microwave Resonator-Based Sensors for Biological Sensing Applications

Proceedings ◽  
2017 ◽  
Vol 1 (4) ◽  
pp. 542 ◽  
Author(s):  
Berk Camli ◽  
Hamdi Torun ◽  
Gunhan Dundar ◽  
Arda D. Yalcinkaya
Keyword(s):  
Microwave Resonator ◽  
Biological Sensing ◽  
Sensing Applications

Computer simulation study about the dependence of amorphous silicon photonic waveguides efficiency on the material quality

2020 ◽  
Vol 90 (3) ◽  
pp. 30502
Author(s):  
Alessandro Fantoni ◽  
João Costa ◽  
Paulo Lourenço ◽  
Manuela Vieira
Keyword(s):  
Amorphous Silicon ◽  
High Throughput Screening ◽  
Simulation Analysis ◽  
Low Cost ◽  
Deposition Process ◽  
Large Area ◽  
Sidewall Roughness ◽  
Sensing Applications ◽  
Fabrication Defects ◽  
The Impact

Amorphous silicon PECVD photonic integrated devices are promising candidates for low cost sensing applications. This manuscript reports a simulation analysis about the impact on the overall efficiency caused by the lithography imperfections in the deposition process. The tolerance to the fabrication defects of a photonic sensor based on surface plasmonic resonance is analysed. The simulations are performed with FDTD and BPM algorithms. The device is a plasmonic interferometer composed by an a-Si:H waveguide covered by a thin gold layer. The sensing analysis is performed by equally splitting the input light into two arms, allowing the sensor to be calibrated by its reference arm. Two different 1 × 2 power splitter configurations are presented: a directional coupler and a multimode interference splitter. The waveguide sidewall roughness is considered as the major negative effect caused by deposition imperfections. The simulation results show that plasmonic effects can be excited in the interferometric waveguide structure, allowing a sensing device with enough sensitivity to support the functioning of a bio sensor for high throughput screening. In addition, the good tolerance to the waveguide wall roughness, points out the PECVD deposition technique as reliable method for the overall sensor system to be produced in a low-cost system. The large area deposition of photonics structures, allowed by the PECVD method, can be explored to design a multiplexed system for analysis of multiple biomarkers to further increase the tolerance to fabrication defects.

Sign in / Sign up

Export Citation Format

Share Document