Effect of cavitation on leakages through active contact of involute toothed external gear pump

2021 ◽  
Author(s):  
Vineet Sahoo
Keyword(s):  
Gear Pump ◽  
External Gear Pump

scholarly journals Parameterization, Modeling, and Validation in Real Conditions of an External Gear Pump

2021 ◽  
Vol 13 (6) ◽  
pp. 3089
Author(s):  
Miquel Torrent ◽  
Pedro Javier Gamez-Montero ◽  
Esteban Codina
Keyword(s):  
Working Conditions ◽  
Test Bench ◽  
Fluid Dynamic ◽  
Graph Model ◽  
Field Tests ◽  
Black Box ◽  
Gear Pump ◽  
Volumetric Behavior ◽  
External Gear Pump ◽  
Standard Tests

This article presents a methodology for predicting the fluid dynamic behavior of a gear pump over its operating range. Complete pump parameterization was carried out through standard tests, and these parameters were used to create a bond graph model to simulate the behavior of the unit. This model was experimentally validated under working conditions in field tests. To carry this out, the pump was used to drive the auxiliary movements of a drilling machine, and the experimental data were compared with a simulation of the volumetric behavior under the same conditions. This paper aims to describe a method for characterizing any hydrostatic pump as a “black box” model predicting its behavior in any operating condition. The novelty of this method is based on the correspondence between the variation of the parameters and the internal changes of the unit when working in real conditions, that is, outside a test bench.

The Research on Pure Water Hydraulic External Gear Pump

2010 ◽  
Vol 44-47 ◽  
pp. 1767-1772
Author(s):  
De Xin Zhao ◽  
Rui Bo Yuan ◽  
Jing Luo
Keyword(s):  
Surface Treatment ◽  
Structural Design ◽  
Treatment Process ◽  
Pure Water ◽  
Spare Part ◽  
Gear Pump ◽  
Calculation Of Parameters ◽  
Water Hydraulic ◽  
Engineering Materials ◽  
External Gear Pump

This article describes the structure of pure water hydraulic external gear pump, structural design and calculation of parameters,analysises the mai spare part material of pure water hydraulic external gear pump and determines the type of the new engineering materials. Besides the surface treatment process of pump are discussed. Pure water hydraulic external gear pump is simulated by FLUENT, obtaining the parameters of the influence of the pump's performance.

Computer Prediction of Cyclic Excitation Sources for an External Gear Pump

1985 ◽  
Vol 199 (3) ◽  
pp. 175-180 ◽  
Author(s):  
K Foster ◽  
R Taylor ◽  
I M Bidhendi
Keyword(s):  
Computer Program ◽  
Gear Pump ◽  
Computer Prediction ◽  
Pressure Distributions ◽  
External Gear Pumps ◽  
Theoretical Predictions ◽  
Gear Pumps ◽  
External Gear Pump

A description is given of a computer program for investigating the performance of the external gear pumps under varying conditions with the special emphasis on the examination of pressure distributions within the pump, i.e. excitation forces for the vibration of the pump case and the variation in flow generated by the pump. Measurements are presented for the variation with time of tooth space pressure and the results are compared with the theoretical predictions from the computer program.

Experimental Investigation of Flowrate Irregularity in Rotary Gear Pumps

1992 ◽  
Author(s):  
G. Mimmi
Keyword(s):  
Experimental Investigation ◽  
Flow Rate ◽  
Experimental Tests ◽  
Periodic Variation ◽  
Experimental Results ◽  
Gear Pump ◽  
Gear Pumps ◽  
Hot Film ◽  
Instantaneous Flow Rate ◽  
External Gear Pump

Abstract In a previous paper the author proposed a method to reduce the periodic variation in flow rate for an external gear pump. To verify the experimental results, a series of experimental tests on a expressly realized gear pump, was carried out. The pump was equipped with relieving grooves milled into the side plates. The tests were done on a closed piping specifically realized and equipped for measuring the instantaneous flow rate of the fluid through a wedge-shaped hot film probe.

Three-Dimensional Numerical Simulation of an External Gear Pump With Decompression Slot and Meshing Contact Point

2015 ◽  
Vol 137 (4) ◽  
Author(s):  
R. Castilla ◽  
P. J. Gamez-Montero ◽  
D. del Campo ◽  
G. Raush ◽  
M. Garcia-Vilchez ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Contact Point ◽  
Three Dimensional ◽  
Fluid Power ◽  
Gear Pump ◽  
Mesh Quality ◽  
Contact Ratio ◽  
Hexahedral Mesh ◽  
Metal Metal ◽  
External Gear Pump

Recently several works have been published on numerical simulation of an external gear pump (EGP). Such kinds of pumps are simple and relatively inexpensive, and are frequently used in fluid power applications, such as fluid power in aeronautical, mechanical, and civil engineering. Nevertheless, considerable effort is being undertaken to improve efficiency and reduce noise and vibration produced by the flow and pressure pulsations. Numerical simulation of an EGP is not straightforward principally for two main reasons. First, the gearing mechanism between gears makes it difficult to handle a dynamic mesh without a considerable deterioration of mesh quality. Second, the dynamic metal–metal contact simulation is important when high pressure outflow has to be reproduced. The numerical studies published so far are based on a two-dimensional (2D) approximation. The aim of the present work is to contribute to the understanding of the fluid flow inside an EGP by means of a complete three-dimensional (3D) parallel simulation on a cluster. The 3D flow is simulated in a linux cluster with a solver developed with the openfoam Toolbox. The hexahedral mesh quality is maintained by periodically replacing the mesh and interpolating the physical magnitudes fields. The meshing contact point is simulated with the viscous wall approach, using a viscosity model based on wall proximity. The results for the flow rate ripples show a similar behavior to that obtained with 2D simulations. However, the flow presents important differences inside the suction and the discharge chambers, principally in the regions of the pipes' connection. Moreover, the decompression slot below the gearing zone, which can not be simulated with a 2D approximation, enables a more realistic simulation of a contact ratio greater than 1. The results are compared with experimental measurements recently published.

Numerical simulation of three-dimensional external gear pump using immersed solid method

2017 ◽  
Vol 118 ◽  
pp. 539-550 ◽  
Author(s):  
Yonghan Yoon ◽  
Byung-Ho Park ◽  
Jaesool Shim ◽  
Yong-Oun Han ◽  
Byeong-Joo Hong ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Three Dimensional ◽  
Gear Pump ◽  
External Gear Pump
Sign in / Sign up

Export Citation Format

Share Document