Validation of a detailed micro-modeling approach for in-plane loaded partially-grouted reinforced masonry shear walls

2021 ◽  
Author(s):  
Sebastián Calderón ◽  
Gabriele Milani ◽  
Cristián Sandoval
Keyword(s):  
Shear Walls ◽  
Modeling Approach ◽  
Reinforced Masonry ◽  
Micro Modeling

Detailed micro-modeling of partially grouted reinforced masonry shear walls: extended validation and parametric study

2021 ◽  
Vol 21 (3) ◽  
Author(s):  
Sebastián Calderón ◽  
Cristián Sandoval ◽  
Gabriele Milani ◽  
Oriol Arnau
Keyword(s):  
Shear Strength ◽  
Aspect Ratio ◽  
Parametric Study ◽  
Shear Walls ◽  
Lateral Force ◽  
Reinforcement Ratio ◽  
Design Parameters ◽  
Compression Stress ◽  
Reinforced Masonry ◽  
Micro Modeling

AbstractPartially grouted reinforced masonry (PG-RM) shear walls have been widely used as structural elements in low- and medium-rise earthquake-resistant buildings. Nonetheless, assessing its shear strength represents a complex task mainly because the partial grouting provides a non-constant cross section, which results in heterogeneous stress–strain patterns. Consequently, refined modeling techniques are needed to reproduce local failure mechanisms taking place in these walls, which significantly influence the global response. In response to this issue, a detailed micro-modeling approach based on the finite element method was proposed in previous studies by the authors. Although the numerical strategy provided accurate results, further validation is required. Therefore, in this study, the experimental results of seven PG-RM shear walls of multi-perforated clay bricks with bed-joint reinforcement are employed as validation cases. These seven walls presented variations in five design parameters. The validated numerical model was then employed to perform a parametric study to assess the influence of the wall aspect ratio, axial pre-compression stress, and horizontal reinforcement ratio on the in-plane lateral behavior of PG-RM shear walls. The obtained results show that the three studied design parameters modified the crack patterns of the walls. Besides, increasing the axial pre-compression stress or reducing the aspect ratio resulted in higher walls’ shear strength. Additionally, decreasing the horizontal reinforcement ratio or increasing the aspect ratio generated a higher story-drift ratio at maximum lateral force. Finally, it was corroborated that the positive effect of the axial pre-compression stress on the walls’ shear strength decreases inversely proportional to the aspect ratio.

scholarly journals Experimental Investigation into the Seismic Performance of Prefabricated Reinforced Masonry Shear Walls with Vertical Joint Connections

2021 ◽  
Vol 11 (10) ◽  
pp. 4421
Author(s):  
Zhiming Zhang ◽  
Fenglai Wang
Keyword(s):  
Seismic Performance ◽  
Cross Sections ◽  
Shear Walls ◽  
Construction Method ◽  
Shear Capacity ◽  
Initial Stiffness ◽  
Equivalent Viscous Damping ◽  
Displacement Ductility ◽  
Reinforced Masonry ◽  
Cracking Performance

In this study, four single-story reinforced masonry shear walls (RMSWs) (two prefabricated and two cast-in-place) under reversed cyclic loading were tested to evaluate their seismic performance. The aim of the study was to evaluate the shear behavior of RMSWs with flanges at the wall ends as well as the effect of construction method. The test results showed that all specimens had a similar failure mode with diagonal cracking. However, the crack distribution was strongly influenced by the construction method. The lateral capacity of the prefabricated walls was 12% and 27% higher than that of the corresponding cast-in-place walls with respect to the rectangular and T-shaped cross sections. The prefabricated walls showed better post-cracking performance than did the cast-in-place wall. The secant stiffness of all the walls decreased rapidly to approximately 63% of the initial stiffness when the first major diagonal crack was observed. The idealized equivalent elastic-plastic system showed that the prefabricated walls had a greater displacement ductility of 3.2–4.8 than that of the cast-in-place walls with a displacement ductility value of 2.3–2.7. This proved that the vertical joints in prefabricated RMSWs enhanced the seismic performance of walls in shear capacity and ductility. In addition, the equivalent viscous damping of the specimens ranged from 0.13 to 0.26 for prefabricated and cast-in-place walls, respectively.

Out-of-Plane Performance of Reinforced Masonry Shear Walls Constructed with Boundary Elements

2019 ◽  
Vol 145 (8) ◽  
pp. 04019073 ◽  
Author(s):  
Tarek El-Hashimy ◽  
Mohamed Ezzeldin ◽  
Michael Tait ◽  
Wael El-Dakhakhni
Keyword(s):  
Shear Walls ◽  
Boundary Elements ◽  
Reinforced Masonry ◽  
Out Of Plane

scholarly journals Hybrid Micro-Modeling Approach for the Analysis of the Cyclic Behavior of RC Frames

2018 ◽  
Vol 4 ◽  
Author(s):  
Gianni Blasi ◽  
Flavia De Luca ◽  
Maria Antonietta Aiello
Keyword(s):  
Cyclic Behavior ◽  
Modeling Approach ◽  
Rc Frames ◽  
Micro Modeling

In‐Plane Resistance of Reinforced Masonry Shear Walls

1990 ◽  
Vol 116 (3) ◽  
pp. 619-640 ◽  
Author(s):  
P. B. Shing ◽  
M. Schuller ◽  
V. S. Hoskere
Keyword(s):  
Shear Walls ◽  
Reinforced Masonry
Sign in / Sign up

Export Citation Format

Share Document