Reduction of pores and wear rate in electrical discharge coating by using hBN nano powder

2021 ◽  
Author(s):  
Rashi Tyagi ◽  
Suman Swaraj ◽  
Amitava Mandal ◽  
Alok Kumar Das
Keyword(s):  
Wear Rate ◽  
Electrical Discharge ◽  
Nano Powder

CHARACTERIZATION OF ZrB2-SiC COMPOSITES WITH AN ANALYTICAL STUDY ON MATERIAL REMOVAL RATE AND TOOL WEAR RATE DURING ELECTRICAL DISCHARGE MACHINING

2016 ◽  
Vol 40 (3) ◽  
pp. 331-349 ◽  
Author(s):  
S. Sivasankar ◽  
R. Jeyapaul
Keyword(s):  
Wear Rate ◽  
Tool Wear ◽  
Relative Density ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Tool Wear Rate ◽  
Tool Materials

This research work concentrates on Electrical Discharge Machining (EDM) performance evaluation of ZrB2- SiC ceramic matrix composites with different tool materials at various machining parameters. Monolithic ZrB2 possesses lower relative density (98.72%) than composites. ZrB2 with 20 Vol.% of SiC possesses 99.74% of the relative density with improved hardness values. Bend strength and Young’s modulus increase with SiC addition until it reaches 20 Vol% and then decreasing. EDM performance on tool materials of tungsten, niobium, tantalum, graphite and titanium at various levels of pulse on time and pulse off time are analyzed. Graphite produces the best Material removal rate (MRR) for all the workpieces. Tool wear rate decreases with melting point and thermal conductivity of the tool material.

Fabrication and experimental investigation of magnetic field assisted powder mixed electrical discharge machining on machining of aluminum 6061 alloy

2019 ◽  
Vol 233 (12) ◽  
pp. 2283-2291 ◽  
Author(s):  
Arun Kumar Rouniyar ◽  
Pragya Shandilya
Keyword(s):  
Magnetic Field ◽  
Wear Rate ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Tool Wear Rate ◽  
Pulse On Time

Magnetic field assisted powder mixed electrical discharge machining is a hybrid machining process with suitable modification in electrical discharge machining combining the use of magnetic field and fine powder in the dielectric fluid. Aluminum 6061 alloy has found highly significance for the advanced industries like automotive, aerospace, electrical, marine, food processing and chemical due to good corrosion resistance, high strength-to-weight ratio, ease of weldability. In this present work, magnetic field assisted powder mixed electrical discharge machining setup was fabricated and experiments were performed using one factor at a time approach for aluminum 6061 alloy. The individual effect of machining parameters namely, peak current, pulse on time, pulse off time, powder concentration and magnetic field on material removal rate and tool wear rate was investigated. The effect of peak current was found to be dominant on material removal rate and tool wear rate followed by pulse on time, powder concentration and magnetic field. Increase in material removal rate and tool wear rate was observed with increase in peak current, pulse on time and a decrease in pulse off time, whereas, for material removal rate increases and tool wear rate decreases up to the certain value and follow the reverse trend with an increase in powder concentration. Material removal rate was increased and tool wear rate was decreased with increase in magnetic field.

Analysis of MRR and TWR on OHNS Die Steel with Different Electrodes Using Electrical Discharge Machining

2016 ◽  
Vol 22 ◽  
pp. 112-120 ◽  
Author(s):  
S. Nallusamy
Keyword(s):  
Wear Rate ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Dielectric Fluid ◽  
Work Piece ◽  
Tool Wear Rate

Electrical Discharge Machining is a machining method primarily used for hard metals or those that are impossible to be machined with traditional techniques. The experimental investigation of material removal rate and tool wear rate during machining of oil hardened non-shrinking steel with brass and copper electrodes using EDM machine was carried out in this paper. This investigation presents the analysis and evaluation of heat affected zones and surface finish of the work piece using different tool electrodes and varying the machine parameters. The commercial grade kerosene oil has been used as dielectric fluid. The effect of various important EDM parameters such as discharge current (Ip) 2 to12A, pulse duration (Ton and Toff) and sparking voltage (V) of 80±5% have been used to yield the response in terms of Material Removal Rate (MRR) and Tool Wear Rate (TWR). Further a detailed analysis of the heat affected regions was also been carried out by using scanning electron microscopy.

scholarly journals Experimental Study During Electrical Discharge Machining of Reinforced Carbon Fiber Plastic Material

2021 ◽  
Vol 9 (8) ◽  
pp. 1445-1451
Author(s):  
Gaurav Pandey
Keyword(s):  
Surface Roughness ◽  
Carbon Fiber ◽  
Wear Rate ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Removal Rate ◽  
Fiber Composite ◽  
Electrode Wear ◽  
Machining Parameters

Abstract: The proper selection of machining conditions and machining parameter is an important aspect, before going to machine a carbon-fiber composite material by Die sinking electrical discharge machining (EDM). Because these conditions will determine such important characteristics as; Material removal rate (MRR), Electrode wears rate (EWR), and Surface roughness (R). The purpose of this work is to determine the optimal values of machining parameters of electrical discharge machine, while machining carbon-fiber-composite with copper electrode. The work has been based on the affect of four design factors: pulse current(Ip) supplied by power supply system of electrical discharge machine (EDM), pulse-on-time(TON), gap voltage(Vg) and duty cycle () on such characteristic like material removal rate (MRR), electrode wear rate(EWR), and surface roughness(Ra) on work-piece surface. This work has been done by means of the technique of design of experiment (DOE), which provides us to perform the above-mentioned analysis with small number of experiments. In this work, a L9 orthogonal array is used to design the experiment. The adequate selection of machining parameters is very important in manufacturing system, because these parameters determine the surface quality and dimensional accuracy of the manufactured part. The optimal setting of the parameters are determined through experiments planned, conducted and analyzed using the Taguchi method. It is found that material removal rate (MRR) reduces substantially, within the region of experimentation, if the parameters are set at their lowest values, while the parameters set at their highest values increases electrode wear rate (EWR). Keywords: EDM, Material removal rate, Surface roughness, Tool wear rate,

Sign in / Sign up

Export Citation Format

Share Document