Computational study of influence by rotating vaneless diffuser on the performance of centrifugal compressor

2021 ◽  
Author(s):  
Porika Niveditha ◽  
Bhamidi V. S. S. S. Prasad
Keyword(s):  
Centrifugal Compressor ◽  
Computational Study ◽  
Vaneless Diffuser

Sensitivity analysis and optimization of a CO2 centrifugal compressor impeller with a vaneless diffuser

2021 ◽  
Author(s):  
Leandro Oliveira Salviano ◽  
Elóy Esteves Gasparin ◽  
Vitor Cesar N. Mattos ◽  
Bruno Barbizan ◽  
Fábio Saltara ◽  
...  
Keyword(s):  
Sensitivity Analysis ◽  
Centrifugal Compressor ◽  
Vaneless Diffuser ◽  
Compressor Impeller

Effects of Non-Axisymmetric Volute on Rotating Stall in the Vaneless Diffuser of a Centrifugal Compressor

2020 ◽  
Author(s):  
Zitian Niu ◽  
Zhenzhong Sun ◽  
Baotong Wang ◽  
Xinqian Zheng
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Centrifugal Compressor ◽  
Stability Boundary ◽  
Rotating Stall ◽  
Evolution Process ◽  
Vaneless Diffuser ◽  
Unstable Flow ◽  
Centrifugal Compressors ◽  
Specific Location

Abstract Rotating stall is an important unstable flow phenomenon that leads to performance degradation and limits the stability boundary in centrifugal compressors. The volute is one of the sources to induce the non-axisymmetric flow in a centrifugal compressor, which has an important effect on the performance of compressors. However, the influence of volute on rotating stall is not clear. Therefore, the effects of volute on rotating stall by experimental and numerical simulation have been explored in this paper. It’s shown that one rotating stall cell generates in a specific location and disappears in another specific location of the vaneless diffuser as a result of the distorted flow field caused by the volute. Also, the cells cannot stably rotate in a whole circle. The frequency related to rotating stall captured in the experiment is 43.9% of the impeller passing frequency (IPF), while it is 44.7% of IPF captured by three-dimensional unsteady numerical simulation, which proves the accuracy of the numerical method in this study. The numerical simulation further reveals that the stall cell initialized in a specific location can be split into several cells during the evolution process. The reason for this is that the blockage in the vaneless diffuser induced by rotating stall is weakened by the mainstream from the impeller exit to make one initialized cell disperse into several ones. The volute has an important influence on the generation and evolution process of the rotating stall cells of compressors. By optimizing volute geometry to reduce the distortion of the flow field, it is expected that rotating stall can be weakened or suppressed, which is helpful to widen the operating range of centrifugal compressors.

Investigation on Effect of Curvilinear Element Blades on Centrifugal Impeller Performance

2017 ◽  
Author(s):  
Kiyotaka Hiradate ◽  
Hiromi Kobayashi ◽  
Takahiro Nishioka
Keyword(s):  
Centrifugal Compressor ◽  
Performance Test ◽  
Design Guidelines ◽  
Secondary Flows ◽  
Flow Coefficient ◽  
Numerical Calculations ◽  
Centrifugal Impeller ◽  
Compressor Stage ◽  
Vaneless Diffuser ◽  
Compressor Impeller

This study experimentally and numerically investigates the effect of application of curvilinear element blades to fully-shrouded centrifugal compressor impeller on the performance of centrifugal compressor stage. Design suction flow coefficient of compressor stage investigated in this study is 0.125. The design guidelines for the curvilinear element blades which had been previously developed was applied to line element blades of a reference conventional impeller and a new centrifugal compressor impeller with curvilinear element blades was designed. Numerical calculations and performance tests of two centrifugal compressor stages with the conventional impeller and the new one were conducted to investigate the effectiveness of application of the curvilinear element blades and compare the inner flowfield in details. Despite 0.5% deterioration of the impeller efficiency, it was confirmed from the performance test results that the compressor stage with the new impeller achieved 1.7% higher stage efficiency at the design point than that with the conventional one. Moreover, it was confirmed that the compressor stage with the new impeller achieved almost the same off-design performance as that of the conventional stage. From results of the numerical calculations and the experiments, it is considered that this efficiency improvement of the new stage was achieved by suppression of the secondary flows in the impeller due to application of negative tangential lean. The suppression of the secondary flows in the impeller achieved uniformalized flow distribution at the impeller outlet and increased the static pressure recovery coefficient in the vaneless diffuser. As a result, it is thought that the total pressure loss was reduced downstream of the vaneless diffuser outlet in the new stage.

Stress Tensor Measurements within the Vaneless Diffuser of a Centrifugal Compressor

1989 ◽  
Vol 203 (1) ◽  
pp. 51-59 ◽  
Author(s):  
T M A Maksoud ◽  
M W Johnson
Keyword(s):  
Centrifugal Compressor ◽  
Sampling Technique ◽  
Phase Lock Loop ◽  
Tangential Component ◽  
Secondary Flows ◽  
Axial Component ◽  
Reynolds Stresses ◽  
Vaneless Diffuser ◽  
Cross Sectional ◽  
Impeller Outlet

Distributions of normal and shear (Reynolds) stresses inside the vaneless diffuser of a low-speed centrifugal compressor are presented. The measurements were made using a triple hot-wire system and a phase lock loop sampling technique. Results were obtained on cross-sectional planes at eight radial stations between the impeller outlet and the diffuser exit at three different flowrates. The turbulence was highly anisotropic and became more so as the flowrate was increased. The tangential component of turbulent intensity was found to be significantly smaller than either the radial or axial component. The blade wake observed at the diffuser inlet decays very rapidly due to the strong tangential Reynolds stresses generated by the opposed secondary flows on either side of the wake. The passage wake decays very much more slowly and is still identifiable at the diffuser discharge.

Flow Behavior of a Centrifugal Compressor With Vaneless Diffuser at Design and Off Design Conditions

2012 ◽  
Author(s):  
Chuang Gao ◽  
Weiguang Huang ◽  
Haiqing Liu ◽  
Hongwu Zhang ◽  
Jundang Shi
Keyword(s):  
Centrifugal Compressor ◽  
Flow Behavior ◽  
Travelling Waves ◽  
Leading Edge ◽  
Pressure Oscillation ◽  
Rotating Stall ◽  
Vaneless Diffuser ◽  
Unstable Flow ◽  
Flow Recirculation ◽  
Static Performance

This paper concerns with the numerical and experimental aspects of both steady and unsteady flow behavior in a centrifugal compressor with vaneless diffuser and downstream collector. Specifically, the appearance of flow instabilities i.e., rotating stall and surge is investigated in great detail. As the first step, the static performance of both stage and component was analyzed and possible root cause of system surge was put forward based on the classic stability theory. Then the unsteady pressure data was utilized to find rotating stall and surge in frequency domain which could be classified as mild surge and deep surge. With the circumferentially installed transducers at impeller inlet, backward travelling waves during stall ramp could be observed. The modes of stall waves could be clearly identified which is caused by impeller leading edge flow recirculation at Mu = 0.96. However, for the unstable flow at Mu = 1.08, the system instability seems to be caused by reversal flow in vaneless diffuser where the pressure oscillation was strongest. Thus steady numerical simulation were performed and validated with the experimental performance data. With the help of numerical analysis, the conjectures are proved.

scholarly journals Rotating Stall in Centrifugal Compressor Vaneless Diffuser: Experimental Analysis of Geometrical Parameters Influence on Phenomenon Evolution

2004 ◽  
Vol 10 (6) ◽  
pp. 433-442 ◽  
Author(s):  
Giovanni Ferrara ◽  
Lorenzo Ferrari ◽  
Leonardo Baldassarre
Keyword(s):  
Centrifugal Compressor ◽  
Dynamic Pressure ◽  
Pressure Sensors ◽  
Experimental Tests ◽  
Fast Response ◽  
Rotating Stall ◽  
Geometrical Parameters ◽  
Vaneless Diffuser ◽  
Response Dynamic ◽  
Frequency Domains

The rotating stall is a key problem for achieving a good working range of a centrifugal compressor and a detailed understanding of the phenomenon is very important to anticipate and avoid it. Many experimental tests have been planned by the authors to investigate the influence on stall behavior of different geometrical configurations. A stage with a backward channel upstream, a 2-D impeller with a vaneless diffuser and a constant cross-section volute downstream, constitute the basic configuration. Several diffuser types with different widths, pinch shapes, and diffusion ratios were tested. The stage was instrumented with many fast response dynamic pressure sensors so as to characterize inception and evolution of the rotating stall. This kind of analysis was carried out both in time and in frequency domains. The methodology used and the results on phenomenon evolution will be presented and discussed in this article.

Sign in / Sign up

Export Citation Format

Share Document