Vertical p-type GaN Schottky barrier diodes with nearly ideal thermionic emission characteristics

2021 ◽  
Vol 118 (2) ◽  
pp. 022102 ◽  
Author(s):  
Kohei Ueno ◽  
Keita Shibahara ◽  
Atsushi Kobayashi ◽  
Hiroshi Fujioka
Keyword(s):  
Schottky Barrier ◽  
Thermionic Emission ◽  
Emission Characteristics ◽  
Schottky Barrier Diodes ◽  
P Type

TEMPERATURE DEPENDENCE OF ELECTRICAL CHARACTERISTICS OF Cr/p–Si(100) SCHOTTKY BARRIER DIODES

2008 ◽  
Vol 22 (14) ◽  
pp. 2309-2319 ◽  
Author(s):  
K. ERTURK ◽  
M. C. HACIISMAILOGLU ◽  
Y. BEKTORE ◽  
M. AHMETOGLU
Keyword(s):  
Temperature Dependence ◽  
Schottky Barrier ◽  
Barrier Height ◽  
Thermionic Emission ◽  
Electrical Characteristics ◽  
Schottky Barrier Diodes ◽  
Semiconductor Interface ◽  
Linear Portion ◽  
Barrier Heights ◽  
P Type

The electrical characteristics of Cr / p – Si (100) Schottky barrier diodes have been measured in the temperature range of 100–300 K. The I-V analysis based on thermionic emission (TE) theory has revealed an abnormal decrease of apparent barrier height and increase of ideality factor at low temperature. The conventional Richardson plot exhibits non-linearity below 200 K with the linear portion corresponding to activation energy 0.304 eV and Richardson constant (A*) value of 5.41×10-3 Acm-2 K -2 is determined from the intercept at the ordinate of this experimental plot, which is much lower than the known value of 32 Acm-2 K -2 for p-type Si . It is demonstrated that these anomalies result due to the barrier height inhomogeneities prevailing at the metal-semiconductor interface. Hence, it has been concluded that the temperature dependence of the I-V characteristics of the Cr/p – Si Schottky barrier diode can be successfully explained on the basis of TE mechanism with a Gaussian distribution of the barrier heights. Furthermore, the value of the Richardson constant found is much closer than that obtained without considering the inhomogeneous barrier heights.

Current Transport in Low-Resistance Metal-InP Contacts

1993 ◽  
Vol 300 ◽  
Author(s):  
Thomas Clausen ◽  
Otto Leistiko
Keyword(s):  
Schottky Barrier ◽  
Ohmic Contact ◽  
Ohmic Contacts ◽  
Current Flow ◽  
Thermionic Emission ◽  
Transport Processes ◽  
Potential Difference ◽  
Current Transport ◽  
Diffusion Limited ◽  
P Type

ABSTRACTThe limiting transport processes for current flow across metal-semiconductor (MS) ohmic contacts to n- and p-type InP have been investigated for Au-based metallizations containing the doping elements Germanium and Zinc. It has been found that the Schottky barrier is lowered and in some cases vanishes during annealing. The current flow for an optimal ohmic contact is diffusion limited by a Fermi potential difference between the alloyed metallization and the bulk InP. For non-optimal ohmic contacts the current flow is also limited by thermionic emission across a low effective Schottky barrier.

High Voltage Schottky Barrier Diodes on P-Type SiC using Metal-Overlap on a Thick Oxide Layer as Edge Termination

1999 ◽  
Vol 572 ◽  
Author(s):  
Q. Zhang ◽  
V. Madangarli ◽  
S. Soloviev ◽  
T. S. Sudarshan
Keyword(s):  
Schottky Barrier ◽  
Oxide Layer ◽  
Breakdown Voltage ◽  
Schottky Diodes ◽  
Schottky Barrier Diodes ◽  
Edge Termination ◽  
Forward Current ◽  
Current Voltage ◽  
Thick Oxide Layer ◽  
P Type

ABSTRACTP-type 6H SiC Schottky barrier diodes with good rectifying characteristics upto breakdown voltage as high as 1000V have been successfully fabricated using metal-overlap over a thick oxide layer (∼ 6000 Å) as edge termination and Al as the barrier metal. The influence of the oxide layer edge termination in improving the reverse breakdown voltage as well as the forward current – voltage characteristics is presented. The terminated Schottky diodes indicate a factor of two higher breakdown voltage and 2–3 times larger forward current densities than those without edge termination. The specific series resistance of the unterminated diodes was ∼228 mΩ-cm2, while that of the terminated diodes was ∼84 mΩ-cm2.

Advances in Multi- and Single-Wafer SiC Epitaxy for the Production and Development of Power Diodes

2008 ◽  
Vol 600-603 ◽  
pp. 95-98 ◽  
Author(s):  
Christian Hecht ◽  
Bernd Thomas ◽  
René A. Stein ◽  
Peter Friedrichs
Keyword(s):  
Schottky Barrier ◽  
Epitaxial Layer ◽  
Memory Effects ◽  
Schottky Barrier Diodes ◽  
Pin Diodes ◽  
Power Diodes ◽  
Homoepitaxial Growth ◽  
Layer Deposition ◽  
Reverse Blocking ◽  
P Type

In this paper, we present results of epitaxial layer deposition for production needs using our hot-wall CVD multi-wafer system VP2000HW from Epigress with a capability of processing 7×3” or 6×100mm wafers per run in a new 100mm setup. Intra-wafer and wafer-to-wafer homogeneities of doping and thickness for full-loaded 6×100mm and 7×3” runs will be shown. Results on Schottky Barrier Diodes (SBD) processed in the multi-wafer system will be given. Furthermore, we show results for n- and p-type SiC homoepitaxial growth on 3”, 4° off-oriented substrates using a single-wafer hot-wall reactor VP508GFR from Epigress for the development of PiN-diodes with blocking voltages above 6.5 kV. Characteristics of n- and p-type epilayers and doping memory effects are discussed. 6.5 kV PiN-diodes were fabricated and electrically characterized. Results on reverse blocking behaviour, forward characteristics and drift stability will be presented.

Sign in / Sign up

Export Citation Format

Share Document