scholarly journals Recyclates made of cast polyamide 6 and carboxilyc acid for blow molding

2020 ◽  
Author(s):  
Axel Grebhardt ◽  
Benjamino Rocco Formisano ◽  
Christian Bonten
Keyword(s):  
Polyamide 6 ◽  
Blow Molding ◽  
Cast Polyamide

High conductive graphite additives for magnesium catalyzed cast PA6 polymer matrix

2010 ◽  
Vol 1 (1) ◽  
pp. 86-89
Author(s):  
Matyas Ando ◽  
Gabor Kalacska ◽  
T. Czigany
Keyword(s):  
Polymer Matrix ◽  
Tribological Properties ◽  
Surface Resistance ◽  
Polyamide 6 ◽  
Mechanical And Tribological Properties ◽  
Base Matrix ◽  
Cast Polyamide

At this article we give a brief review about the additives effects for cast polyamide 6engineering plastics. The natural grade Magnesium catalyzed polyamide 6 has unique mechanicalproperties. Our target is to keep the mechanical and tribological properties with the development ofantistatic and ESD composite version. High conductive very effective to improve the electricalconductivity of magnezium catalized cast PA 6. Only few amount, 0,5% can result good antistaticproperty for the base matrix. Over 3% of additive the surface resistance of the material – performing107 Ω - can reach the ESD (Electrostatic Dissipative) category.

scholarly journals Recycling of cast polyamide 6 using a lubricant

2019 ◽  
Author(s):  
Benjamino Rocco Formisano ◽  
Christian Bonten
Keyword(s):  
Polyamide 6 ◽  
Cast Polyamide

scholarly journals The Effect of Sizes of the Cast Polyamide 6 Rods upon Tensile-Impact Strength

2018 ◽  
Vol 3 (1) ◽  
pp. 21-24
Author(s):  
Miklós Odrobina ◽  
Gábor Kalácska ◽  
Róbert Keresztes
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Technological Process ◽  
Size Range ◽  
Polyamide 6 ◽  
Tensile Impact ◽  
Cast Polyamide ◽  
Different Diameters

We have studied the tensile-impact strength of the magnesium catalysed cast polyamide 6 (PA6) rods according to the EN ISO 8256:2004 standard. The purpose of our investigation was to follow: the mechanical properties of rods are mapped beside same casting technological process in case of different diameters. We have compared the received results with each other than have sought disparities. We examined cylindrical product (rod) in seven dimensional steps in diameter ranging from 40 mm to 300 mm. We have determined that the semi-finished products can be divided into two groups typically in case of their tensile-impact strengths in this size range. The tensile-impact strength is higher in case of the rods with a diameter of less than 100 mm and it is smaller in the larger dimension range. Therefore, the smallest tensile-impact strength can be established in case of the natural semifinished PA6 rods that each rod accomplishes independently of size. However, a range can be determined, which the tensile-impact strength values of product are separated according to the manufacturing size

Dynamic Mechanical Tests on Magnesium Catalyzed Cast Polyamide 6 Composites Having Different Additives

2010 ◽  
Vol 659 ◽  
pp. 269-275 ◽  
Author(s):  
Mátyás Andó ◽  
Gábor Kalácska ◽  
Tibor Czigány
Keyword(s):  
Impact Strength ◽  
Polyamide 6 ◽  
Mechanical Tests ◽  
Dynamic Mechanical ◽  
Base Matrix ◽  
Softening Material ◽  
Cast Polyamide ◽  
The Impact

Due to the effect of graphite and montmorrilonit additives, the impact strenght slightly decreases, but by the influence of softening material, the value of impact strength can be three times more than the pure PA6. It is determined that graphite can be added until 3%, montmorrilonit can be added until 6% and softening material can be added until 15% to the base matrix. These samples give basis for special characteristics examinations.

Monomer cast polyamide 6 composites and their treatment with high-energy electrons

2011 ◽  
Vol 123 (2) ◽  
pp. 1201-1211 ◽  
Author(s):  
G. Engelmann ◽  
U. Gohs ◽  
J. Ganster
Keyword(s):  
Polyamide 6 ◽  
High Energy ◽  
High Energy Electrons ◽  
Cast Polyamide

Tribological characteristics of cast polyamide 6 (PA6G) matrix and their composite (PA6G SL) under normal and overload conditions using dynamic pin-on-plate system

2019 ◽  
Vol 160 ◽  
pp. 119-130 ◽  
Author(s):  
Robert Keresztes ◽  
Miklos Odrobina ◽  
Rajini Nagarajan ◽  
Karthikeyan Subramanian ◽  
Gabor Kalacska ◽  
...  
Keyword(s):  
Polyamide 6 ◽  
Tribological Characteristics ◽  
Cast Polyamide ◽  
Plate System

MOLDSTAR 90

Alloy Digest ◽  
2005 ◽  
Vol 54 (3) ◽  
Keyword(s):  
Compressive Strength ◽  
Injection Molding ◽  
Physical Properties ◽  
Surface Treatment ◽  
Tensile Properties ◽  
Copper Alloy ◽  
High Performance ◽  
Blow Molding

Abstract MoldStar 90 is a high-performance beryllium-free copper alloy for the blow-molding and injection-molding industries. This datasheet provides information on composition, physical properties, hardness, tensile properties, and compressive strength. It also includes information on machining, joining, and surface treatment. Filing Code: CU-732. Producer or source: Performance Alloys.

Sign in / Sign up

Export Citation Format

Share Document