Critical study of the effects and numerical simulations of boundary layer transition in lift-based wind turbines at moderate Reynolds numbers

2020 ◽  
Vol 12 (6) ◽  
pp. 063309
Author(s):  
Sercan Acarer
Keyword(s):  
Boundary Layer ◽  
Numerical Simulations ◽  
Wind Turbines ◽  
Reynolds Numbers ◽  
Boundary Layer Transition ◽  
Critical Study ◽  
Layer Transition

Effects of Reynolds Number and Free-Stream Turbulence on Boundary Layer Transition in a Compressor Cascade

2000 ◽  
Author(s):  
Heinz-Adolf Schreiber ◽  
Wolfgang Steinert ◽  
Bernhard Küsters
Keyword(s):  
Boundary Layer ◽  
Free Stream ◽  
Reynolds Numbers ◽  
Boundary Layer Transition ◽  
Bypass Transition ◽  
Layer Transition ◽  
Free Stream Turbulence ◽  
High Reynolds Numbers ◽  
High Turbulence ◽  
High Reynolds

An experimental and analytical study has been performed on the effect of Reynolds number and free-stream turbulence on boundary layer transition location on the suction surface of a controlled diffusion airfoil (CDA). The experiments were conducted in a rectilinear cascade facility at Reynolds numbers between 0.7 and 3.0×106 and turbulence intensities from about 0.7 to 4%. An oil streak technique and liquid crystal coatings were used to visualize the boundary layer state. For small turbulence levels and all Reynolds numbers tested the accelerated front portion of the blade is laminar and transition occurs within a laminar separation bubble shortly after the maximum velocity near 35–40% of chord. For high turbulence levels (Tu > 3%) and high Reynolds numbers transition propagates upstream into the accelerated front portion of the CDA blade. For those conditions, the sensitivity to surface roughness increases considerably and at Tu = 4% bypass transition is observed near 7–10% of chord. Experimental results are compared to theoretical predictions using the transition model which is implemented in the MISES code of Youngren and Drela. Overall the results indicate that early bypass transition at high turbulence levels must alter the profile velocity distribution for compressor blades that are designed and optimized for high Reynolds numbers.

Velocity and Pressure Measurements Along a Row of Confined Cylinders

2006 ◽  
Author(s):  
Barton L. Smith ◽  
Jack J. Stepan ◽  
Donald M. McEligot
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Symmetry Plane ◽  
Field Measurements ◽  
Reynolds Numbers ◽  
Boundary Layer Transition ◽  
Recirculation Region ◽  
Pressure Measurements ◽  
Layer Transition ◽  
Flow Experiments

The results of flow experiments performed in a cylinder array designed to mimic a VHTR Nuclear Plant lower plenum design are presented. Pressure drop and velocity field measurements were made. Based on these measurements, five regimes of behavior are identified that are found to depend on Reynolds number. It is found that the recirculation region behind the cylinders is shorter than that of half cylinders placed on the wall representing the symmetry plane. Unlike a single cylinder, the separation point is found to always be on the rear of the cylinders, even at very low Reynolds number. Boundary layer transition is found to occur at much lower Reynolds numbers than previously reported.

Boundary-Layer Control as a Means of Reducing Drag on Fully Submerged Bodies of Revolution

1985 ◽  
Vol 107 (3) ◽  
pp. 342-347 ◽  
Author(s):  
B. Bar-Haim ◽  
D. Weihs
Keyword(s):  
Boundary Layer ◽  
Reynolds Numbers ◽  
Boundary Layer Transition ◽  
Boundary Layer Control ◽  
Layer Transition ◽  
Bodies Of Revolution ◽  
Boundary Layer Suction ◽  
Technique Optimization ◽  
Axisymmetric Bodies ◽  
Layer Control

The drag of axisymmetric bodies can be reduced by boundary-layer suction, which delays transition and can control separation. In this study, boundary-layer transition is delayed by applying a distributed suction technique. Optimization calculations were performed to define the minimal drag bodies at Reynolds numbers of 107 and 108. The saving in drag relative to optimal bodies with non-controlled boundary layers is shown to be 18 and 78 percent, at Reynolds numbers of 107 and 108, respectively.

Numerical simulations of boundary-layer transition induced by a cylinder wake

2006 ◽  
Vol 547 (-1) ◽  
pp. 413 ◽  
Author(s):  
VICTOR OVCHINNIKOV ◽  
UGO PIOMELLI ◽  
MEELAN M. CHOUDHARI
Keyword(s):  
Boundary Layer ◽  
Numerical Simulations ◽  
Boundary Layer Transition ◽  
Cylinder Wake ◽  
Layer Transition

Effect of Tripping Laminar-to-Turbulent Boundary Layer Transition on Tip Vortex Cavitation

1997 ◽  
Vol 41 (01) ◽  
pp. 1-9
Author(s):  
T. Pichon ◽  
A. Pauchet ◽  
A. Astolfi ◽  
D. H. Fruman ◽  
J-Y. Billard
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Flat Plate ◽  
Cross Section ◽  
Lift Coefficient ◽  
Reynolds Numbers ◽  
Boundary Layer Transition ◽  
Tip Vortex ◽  
Layer Transition ◽  
Tip Vortex Cavitation

It is by now well established that, for Reynolds numbers larger than those corresponding to the conditions of laminar-to-turbulent boundary layer transition over a flat plate (≈0.5 × 106) and for a variety of wing shapes and cross sections, desinent cavitation numbers divided by the Reynolds number to the power 0.4 correlate with the square of the lift coefficient. In the case of foils having an NACA 16020 cross section and for Reynolds numbers below or close to those leading to transition over a flat plate, the results are very much different from those obtained for well-developed turbulent boundary layer conditions. Thus, a research program has been conducted in order to investigate the effect of boundary layer manipulation on cavitation occurrence. It consisted in determining the critical cavitation numbers, the lift coefficients, and the velocities in the tip vortex of foils having either a smooth surface or tripping roughness (promoters) near the leading edge. Tests were performed using elliptical foils of NACA 16020 cross section having the promoters extending over 60, 80 and 90 percent of the semi-span. The region near the tip was kept smooth in order to distinguish laminar-to-turbulent transition effects from tip vortex cavitation inhibition effects associated with artificial roughness at the wing tip. Results obtained at very low Reynolds numbers, ≥ 0.24 × 106, with the foil tripped on both the pressure and suction sides collapse rather well with those previously obtained at much larger Reynolds numbers with the smooth foil, and correlate with the square of the lift coefficient. The differences between the tripped and smooth foil results are due to the modification of the lift characteristics through the modification of the wing boundary layer, as shown by flow visualization studies, and as a result of the local tip vortex intensity.

Predicting Separation and Transitional Flow in Turbine Blades at Low Reynolds Numbers—Part I: Development of Prediction Methodology

2010 ◽  
Vol 133 (3) ◽  
Author(s):  
Darius D. Sanders ◽  
Walter F. O’Brien ◽  
Rolf Sondergaard ◽  
Marc D. Polanka ◽  
Douglas C. Rabe
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Flow Model ◽  
Reynolds Numbers ◽  
Boundary Layer Transition ◽  
Transitional Flow ◽  
Layer Transition ◽  
Low Pressure Turbine ◽  
Low Reynolds ◽  
And Performance

There is an increasing interest in design methods and performance prediction for aircraft engine turbines operating at low Reynolds numbers. In this regime, boundary layer separation may be more likely to occur in the turbine flow passages. For accurate computational fluid dynamics (CFD) predictions of the flow, correct modeling of laminar-turbulent boundary layer transition is essential to capture the details of the flow. To investigate possible improvements in model fidelity, CFD models were created for the flow over two low pressure turbine blade designs. A new three-equation eddy-viscosity type turbulent transitional flow model, originally developed by Walters and Leylek (2004, “A New Model for Boundary Layer Transition Using a Single Point RANS Approach,” ASME J. Turbomach., 126(1), pp. 193–202), was employed for the current Reynolds averaged Navier–Stokes (RANS) CFD calculations. Previous studies demonstrated the ability of this model to accurately predict separation and boundary layer transition characteristics of low Reynolds number flows. The present research tested the capability of CFD with the Walters and Leylek turbulent transitional flow model to predict the boundary layer behavior and performance of two different turbine cascade configurations. Flows over low pressure turbine (LPT) blade airfoils with different blade loading characteristics were simulated over a Reynolds number range of 15,000–100,000 and predictions were compared with experimental cascade results. Part I of this paper discusses the prediction methodology that was developed and its validation using a lightly loaded LPT blade airfoil design. The turbulent transitional flow model sensitivity to turbulent flow parameters was investigated and showed a strong dependence on freestream turbulence intensity with a second-order effect of turbulent length scale. Focusing on the calculation of the total pressure loss coefficients to judge performance, the CFD simulation incorporating Walters and Leylek’s turbulent transitional flow model produced adequate prediction of the Reynolds number performance for the lightly loaded LPT blade cascade geometry. Significant improvements in performance were shown over predictions of conventional RANS turbulence models. Historically, these models cannot adequately predict boundary layer transition.

Sign in / Sign up

Export Citation Format

Share Document