First principle study of bias voltage dependent Schottky barrier height of Pt/MgO interface

2020 ◽  
Author(s):  
M. Ramesh ◽  
Manish K. Niranjan
Keyword(s):  
Schottky Barrier ◽  
Barrier Height ◽  
Bias Voltage ◽  
Schottky Barrier Height ◽  
First Principle ◽  
Voltage Dependent

Fabrication of 1.2kV, 100A, 4H-SiC(0001) and (000-1) Junction Barrier Schottky Diodes with Almost Same Schottky Barrier Height

2010 ◽  
Vol 645-648 ◽  
pp. 893-896 ◽  
Author(s):  
Akimasa Kinoshita ◽  
Takasumi Ohyanagi ◽  
Tsutomu Yatsuo ◽  
Kenji Fukuda ◽  
Hajime Okumura ◽  
...  
Keyword(s):  
Schottky Barrier ◽  
Barrier Height ◽  
Bias Voltage ◽  
Schottky Barrier Height ◽  
Annealing Temperature ◽  
Schottky Diodes ◽  
Forward Bias ◽  
Leakage Currents ◽  
Forward Bias Voltage ◽  
The Ideal

It is known that a Schottky barrier height (b) of metal/C-face 4H-SiC Schottky barrier diode (SBD) differ from b of metal/Si-face 4H-SiC SBD. Furthermore, b of metal/4H-SiC SBD varies with annealing temperature. We fabricate 0.231mm2 SBD with Ti/SiC interface using Si-face and C-face 4H-SiC. These SBDs are annealed at several temperatures after a formation of the Ti/SiC interface. As a result, b of Ti/C-face 4H-SiC interface annealed at 400 oC is nearly equal to b of Ti/Si-face 4H-SiC interface annealed at 500 oC and the n-values of these SBDs are nearly equal to the ideal value (unity). Using that annealing condition, we fabricated 25mm2 junction barrier Schottky (JBS) diodes with Ti/SiC interface on Si-face and C-face 4H-SiC epitaxial substrate. b of Si-face and C-face JBS diodes are 1.26eV and 1.24eV, respectively. The leakage currents for both Si-face and C-face JBS diodes are less than 1mA/cm2. The current of 100A is obtained at the forward bias voltage of 1.95V and 2.16V for the Si-face JBS and the C-face JBS.

scholarly journals A Study about Schottky Barrier Height and Ideality Factor in Thin Film Transistors with Metal/Zinc Oxide Nanoparticles Structures Aiming Flexible Electronics Application

Nanomaterials ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 1188
Author(s):  
Ivan Rodrigo Kaufmann ◽  
Onur Zerey ◽  
Thorsten Meyers ◽  
Julia Reker ◽  
Fábio Vidor ◽  
...  
Keyword(s):  
Thin Film ◽  
Zinc Oxide ◽  
Schottky Barrier ◽  
Barrier Height ◽  
Flexible Electronics ◽  
Thin Film Transistors ◽  
Zinc Oxide Nanoparticles ◽  
Schottky Barrier Height ◽  
Oxide Nanoparticles ◽  
Semiconductor Interfaces

Zinc oxide nanoparticles (ZnO NP) used for the channel region in inverted coplanar setup in Thin Film Transistors (TFT) were the focus of this study. The regions between the source electrode and the ZnO NP and the drain electrode were under investigation as they produce a Schottky barrier in metal-semiconductor interfaces. A more general Thermionic emission theory must be evaluated: one that considers both metal/semiconductor interfaces (MSM structures). Aluminum, gold, and nickel were used as metallization layers for source and drain electrodes. An organic-inorganic nanocomposite was used as a gate dielectric. The TFTs transfer and output characteristics curves were extracted, and a numerical computational program was used for fitting the data; hence information about Schottky Barrier Height (SBH) and ideality factors for each TFT could be estimated. The nickel metallization appears with the lowest SBH among the metals investigated. For this metal and for higher drain-to-source voltages, the SBH tended to converge to some value around 0.3 eV. The developed fitting method showed good fitting accuracy even when the metallization produced different SBH in each metal-semiconductor interface, as was the case for gold metallization. The Schottky effect is also present and was studied when the drain-to-source voltages and/or the gate voltage were increased.

Schottky barrier height on thermally oxidized InAlN surface evaluated by electrical and optical measurements

2011 ◽  
Vol 98 (16) ◽  
pp. 162111 ◽  
Author(s):  
J. Kováč ◽  
R. Šramatý ◽  
A. Chvála ◽  
H. Sibboni ◽  
E. Morvan ◽  
...  
Keyword(s):  
Schottky Barrier ◽  
Barrier Height ◽  
Schottky Barrier Height ◽  
Optical Measurements

Effective Schottky Barrier Height Lowering by TiN Capping Layer for TiSix/Si Power Diode

2015 ◽  
Vol 36 (6) ◽  
pp. 597-599 ◽  
Author(s):  
Lin-Lin Wang ◽  
Wu Peng ◽  
Yu-Long Jiang ◽  
Bing-Zong Li
Keyword(s):  
Schottky Barrier ◽  
Barrier Height ◽  
Schottky Barrier Height ◽  
Capping Layer ◽  
Power Diode

Schottky Barrier Height Engineering in NiGe/n-Ge(001) Contacts by Germanidation Induced Dopant Segregation

2007 ◽  
Vol 994 ◽  
Author(s):  
S. L. Liew ◽  
C. T. Chua ◽  
D. H. L Seng ◽  
D. Z. Chi
Keyword(s):  
Schottky Barrier ◽  
Barrier Height ◽  
Schottky Barrier Height ◽  
Dopant Segregation

AbstractSchottky barrier height (ÖB) engineering of NiGe/n-Ge(001) diodes was achieved through germanidation induced dopant segregation on As implanted-Ge substrates. was reduced from 0.55 eV to 0.16 eV with increasing As dose on n-Ge(001) while on p-Ge(001), the diodes exhibited increasing ÖB.

Sign in / Sign up

Export Citation Format

Share Document