Mean‐velocity scaling in and around a mild, turbulent separation bubble

1995 ◽  
Vol 7 (8) ◽  
pp. 1956-1969 ◽  
Author(s):  
Amy E. Alving ◽  
H. H. Fernholz
Keyword(s):  
Separation Bubble ◽  
Mean Velocity ◽  
Turbulent Separation

Numerical study of a turbulent separation bubble with sweep

2019 ◽  
Vol 880 ◽  
pp. 684-706
Author(s):  
G. N. Coleman ◽  
C. L. Rumsey ◽  
P. R. Spalart
Keyword(s):  
Pressure Gradient ◽  
Numerical Study ◽  
Separation Bubble ◽  
Laminar Flows ◽  
Swept Wing ◽  
Mean Velocity ◽  
Independence Principle ◽  
Velocity Magnitude ◽  
Turbulent Separation ◽  
Swept Wings

Direct numerical simulation (DNS) is used to study a separated and rapidly reattached turbulent boundary layer over an idealized $35^{\circ }$ infinite swept wing. The separation and reattachment are induced by a transpiration profile at fixed distance above the layer, with the pressure gradient applied to a well-defined, fully developed, zero-pressure-gradient (ZPG) collateral state. To isolate the influence of the sweep, results are compared with one of our earlier DNS of an unswept flow, with the same chordwise transpiration distribution and appropriate upstream momentum thickness. The independence principle (IP) traditionally proposed for swept wings, which is exact for laminar flows, is found to be close to valid in some regions (bridging the separation/reattachment zone) and to fail in others (in the ZPG layers upstream and downstream of the separation). This is assessed primarily through the skin friction and integral thicknesses. The regions in which the IP is approximately valid correspond to regions of diminished Reynolds-stress divergence, compared to the pressure-gradient magnitude. The mean-velocity profiles exhibit significant skewing as the flow develops, while the velocity magnitude departs only slightly from the ZPG logarithmic profile, even above the separation zone. Implications for Reynolds-averaged turbulence modelling are discussed.

Active Forcing of a Pressure-Induced Turbulent Separation Bubble

2020 ◽  
Author(s):  
Abdelouahab T. Mohammed-Taifour ◽  
Arnaud Le Floc'h ◽  
Julien Weiss
Keyword(s):  
Separation Bubble ◽  
Turbulent Separation

On turbulent boundary-layer separation

1968 ◽  
Vol 32 (2) ◽  
pp. 293-304 ◽  
Author(s):  
V. A. Sandborn ◽  
C. Y. Liu
Keyword(s):  
Boundary Layer ◽  
Shear Stress ◽  
Turbulent Boundary Layer ◽  
Analytical Study ◽  
Boundary Layer Separation ◽  
Mean Velocity ◽  
Laminar Separation ◽  
Layer Separation ◽  
Turbulent Separation ◽  
Separation Model

An experimental and analytical study of the separation of a turbulent boundary layer is reported. The turbulent boundary-layer separation model proposed by Sandborn & Kline (1961) is demonstrated to predict the experimental results. Two distinct turbulent separation regions, an intermittent and a steady separation, with correspondingly different velocity distributions are confirmed. The true zero wall shear stress turbulent separation point is determined by electronic means. The associated mean velocity profile is shown to belong to the same family of profiles as found for laminar separation. The velocity distribution at the point of reattachment of a turbulent boundary layer behind a step is also shown to belong to the laminar separation family.Prediction of the location of steady turbulent boundary-layer separation is made using the technique employed by Stratford (1959) for intermittent separation.

Rotating Effect on Fluid Flow in Two Smooth Ducts Connected by a 180-Degree Bend

2003 ◽  
Vol 125 (1) ◽  
pp. 138-148 ◽  
Author(s):  
Tong-Miin Liou ◽  
Chung-Chu Chen ◽  
Meng-Yu Chen
Keyword(s):  
Heat Transfer ◽  
Kinetic Energy ◽  
Secondary Flow ◽  
Turbulent Kinetic Energy ◽  
Separation Bubble ◽  
Turbine Blades ◽  
Outer Part ◽  
Intensity Level ◽  
Mean Velocity ◽  
Sharp Turn

Laser Doppler velocimetry (LDV) measurements are presented of turbulent flow in a two-pass square-sectioned smooth duct simulating the coolant passages employed in gas turbine blades under rotating and nonrotating conditions. For all cases studied, the Reynolds number characterized by duct hydraulic diameter and bulk mean velocity was fixed at 1×104. The rotation number Ro was varied from 0 to 0.2. It is found that as Ro is increased, both the skewness (SK) of streamwise mean velocity and magnitude of secondary-flow velocity increase linearly, SK=2.3 Ro and U2+V2¯/Uh=2.3 Ro+0.4, and the magnitude of turbulence intensity level increases exponentially. As Ro is increased, the curvature induced symmetric Dean vortices in the turn for Ro=0 is gradually dominated by a single vortex most of which impinges directly on the outer part of leading wall. The high turbulent kinetic energy is closely related to the dominant vortex prevailing inside the 180-deg sharp turn. The size of separation bubble immediately after the turn is found to diminish to null as Ro is increased from 0 to 0.2. A simple correlation is developed between the bubble size and Ro. A critical range of Ro responsible for the switch of faster moving flow from near the outer wall to the inner wall is identified. For both rotating and nonrotating cases, the direction and strength of the secondary flow with respect to the wall are the most important fluid dynamic factors affecting local the heat transfer distributions inside a 180-deg sharp turn. The role of the turbulent kinetic energy in the overall enhancement of heat transfer is well addressed.

Shear Layer Development, Separation, and Stability Over a Low-Reynolds Number Airfoil

2018 ◽  
Vol 140 (7) ◽  
Author(s):  
Paul Ziadé ◽  
Mark A. Feero ◽  
Philippe Lavoie ◽  
Pierre E. Sullivan
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Shear Layer ◽  
Separation Bubble ◽  
Low Reynolds Number ◽  
Base Flow ◽  
Mean Velocity ◽  
Laminar Separation ◽  
Low Reynolds ◽  
Layer Development

The shear layer development for a NACA 0025 airfoil at a low Reynolds number was investigated experimentally and numerically using large eddy simulation (LES). Two angles of attack (AOAs) were considered: 5 deg and 12 deg. Experiments and numerics confirm that two flow regimes are present. The first regime, present for an angle-of-attack of 5 deg, exhibits boundary layer reattachment with formation of a laminar separation bubble. The second regime consists of boundary layer separation without reattachment. Linear stability analysis (LSA) of mean velocity profiles is shown to provide adequate agreement between measured and computed growth rates. The stability equations exhibit significant sensitivity to variations in the base flow. This highlights that caution must be applied when experimental or computational uncertainties are present, particularly when performing comparisons. LSA suggests that the first regime is characterized by high frequency instabilities with low spatial growth, whereas the second regime experiences low frequency instabilities with more rapid growth. Spectral analysis confirms the dominance of a central frequency in the laminar separation region of the shear layer, and the importance of nonlinear interactions with harmonics in the transition process.

Heat Transfer on a Flat Surface Under a Region of Turbulent Separation

1992 ◽  
Author(s):  
R. B. Rivir ◽  
J. P. Johnston ◽  
J. K. Eaton
Keyword(s):  
Heat Transfer ◽  
Pressure Gradient ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Separation Bubble ◽  
Adverse Pressure Gradient ◽  
Constant Heat Flux ◽  
Opposite Wall ◽  
Turbulent Separation ◽  
Full Separation

Fluid dynamics and heat transfer measurements were performed for a separation bubble formed on a smooth, flat, constant-heat-flux plate. The separation was induced by an adverse pressure gradient created by deflection of the opposite wall of the wind tunnel. The heat transfer rate was found to decline monotonically approaching the separation point and reach a broad minimum approximately 60% below zero-pressure-gradient levels. The heat transfer rate increased rapidly approaching reattachment with a peak occuring slightly downstream of the mean reattachment point. The opposite wall shape was varied to reduce the applied adverse pressure gradient. The heat transfer results were similar as long as the pressure gradient was sufficient to cause full separation of the boundary layer.

Control of trailing-edge separation by tangential blowing inside the bubble

2004 ◽  
Vol 108 (1086) ◽  
pp. 419-425 ◽  
Author(s):  
P. R. Viswanath ◽  
K. T. Madhavan
Keyword(s):  
Separation Bubble ◽  
Effective Means ◽  
Separated Flow ◽  
Wake Flow ◽  
Turbulent Shear ◽  
Trailing Edge ◽  
Mean Velocity ◽  
Turbulent Shear Stress ◽  
Edge Separation ◽  
Tangential Blowing

Abstract Experiments have been performed investigating the effectiveness of steady tangential blowing, with the blowing slot located downstream of separation (but inside the separation bubble) to control a trailing-edge separated flow at low speeds. Trailing-edge separation was induced on a two-dimensional aerofoil-like body and the shear layer closure occurred in the near-wake. Measurements made consisted of model surface pressures and mean velocity, turbulent shear stress and kinetic energy profiles in the separated zone using a two-component LDV system. It is explicitly demonstrated that the novel concept of tangential blowing inside the bubble can be an effective means of control for trailing-edge separated flows as well. Blowing mass and momentum requirements for the suppression of wall and wake flow reversals have been estimated.

Spanwise Aspects of Unsteadiness in a Pressure-Induced Turbulent Separation Bubble

2018 ◽  
Author(s):  
Arnaud S. Le Floc'h ◽  
Abdelouahab T. Mohammed-Taifour ◽  
Louis Dufresne ◽  
Julien Weiss
Keyword(s):  
Separation Bubble ◽  
Turbulent Separation
Sign in / Sign up

Export Citation Format

Share Document