X-ray diffraction method for quantitative estimation of elastic modulus in materials with gradient structure

2019 ◽  
Author(s):  
Marina Ostapenko ◽  
Ludmila Meisner
1991 ◽  
Vol 35 (A) ◽  
pp. 545-552 ◽  
Author(s):  
Katsuhiko Nakamae ◽  
Takashi Nishino

AbstractElastic modulus EI of crystalline regions of various high polymers in the direction parallel to the chain axis were measured using an X-ray diffraction method. The crystal deformation can be detected directly by the diffraction peak shift as a function of applied constant stress. The stress in the crystalline regions is assumed to be equal to that applied to the specimen. The validity of this assumption has been proven experimentally for polyethylene, poly(p-phenylene terephthalamide) and so on. The EI values were discussed in relation to molecular conformation and deformation mechanism of the chains.


Author(s):  
Bibin Jose ◽  
Manikandan Manoharan ◽  
Arivazhagan Natarajan

Residual stresses are inherent stresses that exist in engineering components even though no external load is applied. They are caused by the non-uniform volumetric shift of the metallic component during manufacturing processes. Welding is a key manufacturing technique that has a substantial impact on the economy since it is required for the production of a diverse variety of products used in the engineering sector. The residual stress primarily affects the stability, durability and performance of the welded joints. Hence its determination is of utmost importance. X-ray diffraction (XRD) is the most commonly used method for residual stress analysis. There are mainly two approaches for measuring residual stress using XRD; one is the sin2ψ method and the other is the cosα method. The residual stress measurements using the cosα method are handy, quick and convenient compared to the sin2ψ method. This method is well suited for welded joints, as it provides flexibility for testing immediately after the welding operation. Apart from residual stress measurements, the cosα method also gives valuable insights in the form of Debye-Scherrer (DS) rings and full width at half maximum. The present study focuses on the development of a novel technique that not only enables residual stress measurement but also provides a quantitative estimation of hardness and qualitative estimation of grain size without performing metallurgical or mechanical characterization. The material used for the present study is an arc-welded joint of MDN 250 grade maraging steel. The residual stress results show a compressive profile throughout the weldment, with a maximum value of compressive residual stress of 428 MPa at the fusion zone.


2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Durga Sankar Vavilapalli ◽  
Ambrose A. Melvin ◽  
F. Bellarmine ◽  
Ramanjaneyulu Mannam ◽  
Srihari Velaga ◽  
...  

AbstractIdeal sillenite type Bi12FeO20 (BFO) micron sized single crystals have been successfully grown via inexpensive hydrothermal method. The refined single crystal X-ray diffraction data reveals cubic Bi12FeO20 structure with single crystal parameters. Occurrence of rare Fe4+ state is identified via X-ray photoelectron spectroscopy (XPS) and X-ray absorption spectroscopy (XAS). The lattice parameter (a) and corresponding molar volume (Vm) of Bi12FeO20 have been measured in the temperature range of 30–700 °C by the X-ray diffraction method. The thermal expansion coefficient (α) 3.93 × 10–5 K−1 was calculated from the measured values of the parameters. Electronic structure and density of states are investigated by first principle calculations. Photoelectrochemical measurements on single crystals with bandgap of 2 eV reveal significant photo response. The photoactivity of as grown crystals were further investigated by degrading organic effluents such as Methylene blue (MB) and Congo red (CR) under natural sunlight. BFO showed photodegradation efficiency about 74.23% and 32.10% for degrading MB and CR respectively. Interesting morphology and microstructure of pointed spearhead like BFO crystals provide a new insight in designing and synthesizing multifunctional single crystals.


Crystals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 753
Author(s):  
Dmitriy Shlimas ◽  
Artem L. Kozlovskiy ◽  
Maxim Zdorovets

The interest in lithium-containing ceramics is due to their huge potential as blanket materials for thermonuclear reactors for the accumulation of tritium. However, an important factor in their use is the preservation of the stability of their strength and structural properties when under the influence of external factors that determine the time frame of their operation. This paper presents the results of a study that investigated the influence of the LiTiO2 phase on the increasing resistance to degradation and corrosion of Li2TiO3 ceramic when exposed to aggressive acidic media. Using the X-ray diffraction method, it was found that an increase in the concentration of LiClO4·3H2O during synthesis leads to the formation of a cubic LiTiO2 phase in the structure as a result of thermal sintering of the samples. During corrosion tests, it was found that the presence of the LiTiO2 phase leads to a decrease in the degradation rate in acidic media by 20–70%, depending on the concentration of the phase. At the same time, and in contrast to the samples of Li2TiO3 ceramics, for which the mechanisms of degradation during a long stay in aggressive media are accompanied by large mass losses, for the samples containing the LiTiO2 phase, the main degradation mechanism is pitting corrosion with the formation of pitting inclusions.


1990 ◽  
Vol 7 (7) ◽  
pp. 308-311
Author(s):  
Li Chaorong ◽  
Mai Zhenhong ◽  
Cui Shufan ◽  
Zhou Junming ◽  
Yutian Wang

1951 ◽  
Vol 22 (5) ◽  
pp. 665-672 ◽  
Author(s):  
Alfred J. Reis ◽  
Jerome J. Slade ◽  
Sigmund Weissmann

Author(s):  
Sehrish Akram ◽  
Arshad Mehmood ◽  
Sajida Noureen ◽  
Maqsood Ahmed

Thermal-induced transformation of glutamic acid to pyroglutamic acid is well known. However, confusion remains over the exact temperature at which this happens. Moreover, no diffraction data are available to support the transition. In this article, we make a systematic investigation involving thermal analysis, hot-stage microscopy and single-crystal X-ray diffraction to study a one-pot thermal transition of glutamic acid to pyroglutamic acid and subsequent self-cocrystallization between the product (hydrated pyroglutamic acid) and the unreacted precursor (glutamic acid). The melt upon cooling gave a robust cocrystal, namely, glutamic acid–pyroglutamic acid–water (1/1/1), C5H7NO3·C5H9NO4·H2O, whose structure has been elucidated from single-crystal X-ray diffraction data collected at room temperature. A three-dimensional network of strong hydrogen bonds has been found. A Hirshfeld surface analysis was carried out to make a quantitative estimation of the intermolecular interactions. In order to gain insight into the strength and stability of the cocrystal, the transferability principle was utilized to make a topological analysis and to study the electron-density-derived properties. The transferred model has been found to be superior to the classical independent atom model (IAM). The experimental results have been compared with results from a multipolar refinement carried out using theoretical structure factors generated from density functional theory (DFT) calculations. Very strong classical hydrogen bonds drive the cocrystallization and lend stability to the resulting cocrystal. Important conclusions have been drawn about this transition.


Sign in / Sign up

Export Citation Format

Share Document