scholarly journals Evaluation of surface roughness and geometrical characteristic of additive manufacturing inserts for precision injection moulding

2019 ◽  
Author(s):  
A. Davoudinejad ◽  
A. Charalambis ◽  
D. B. Pedersen ◽  
G. Tosello
Keyword(s):  
Surface Roughness ◽  
Additive Manufacturing ◽  
Injection Moulding ◽  
Geometrical Characteristic

scholarly journals Improving surface quality in selective laser melting based tool making

2021 ◽  
Author(s):  
Filippo Simoni ◽  
Andrea Huxol ◽  
Franz-Josef Villmer
Keyword(s):  
Surface Roughness ◽  
Additive Manufacturing ◽  
Surface Quality ◽  
Selective Laser Melting ◽  
Melting Process ◽  
Laser Remelting ◽  
Laser Melting ◽  
Great Cost ◽  
Starting Point ◽  
Processing Techniques

AbstractIn the last years, Additive Manufacturing, thanks to its capability of continuous improvements in performance and cost-efficiency, was able to partly replace and redefine well-established manufacturing processes. This research is based on the idea to achieve great cost and operational benefits especially in the field of tool making for injection molding by combining traditional and additive manufacturing in one process chain. Special attention is given to the surface quality in terms of surface roughness and its optimization directly in the Selective Laser Melting process. This article presents the possibility for a remelting process of the SLM parts as a way to optimize the surfaces of the produced parts. The influence of laser remelting on the surface roughness of the parts is analyzed while varying machine parameters like laser power and scan settings. Laser remelting with optimized parameter settings considerably improves the surface quality of SLM parts and is a great starting point for further post-processing techniques, which require a low initial value of surface roughness.

scholarly journals Directionally-Dependent Mechanical Properties of Ti6Al4V Manufactured by Electron Beam Melting (EBM) and Selective Laser Melting (SLM)

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3603
Author(s):  
Tim Pasang ◽  
Benny Tavlovich ◽  
Omry Yannay ◽  
Ben Jakson ◽  
Mike Fry ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Tensile Strength ◽  
Electron Beam ◽  
Additive Manufacturing ◽  
Selective Laser Melting ◽  
Electron Beam Melting ◽  
Rolling Direction ◽  
Laser Melting ◽  
Plate Rolling

An investigation of mechanical properties of Ti6Al4V produced by additive manufacturing (AM) in the as-printed condition have been conducted and compared with wrought alloys. The AM samples were built by Selective Laser Melting (SLM) and Electron Beam Melting (EBM) in 0°, 45° and 90°—relative to horizontal direction. Similarly, the wrought samples were also cut and tested in the same directions relative to the plate rolling direction. The microstructures of the samples were significantly different on all samples. α′ martensite was observed on the SLM, acicular α on EBM and combination of both on the wrought alloy. EBM samples had higher surface roughness (Ra) compared with both SLM and wrought alloy. SLM samples were comparatively harder than wrought alloy and EBM. Tensile strength of the wrought alloy was higher in all directions except for 45°, where SLM samples showed higher strength than both EBM and wrought alloy on that direction. The ductility of the wrought alloy was consistently higher than both SLM and EBM indicated by clear necking feature on the wrought alloy samples. Dimples were observed on all fracture surfaces.

scholarly journals SURFACE ROUGHNESS CONSIDERATIONS IN DESIGN FOR ADDITIVE MANUFACTURING - A LITERATURE REVIEW

2021 ◽  
Vol 1 ◽  
pp. 2841-2850
Author(s):  
Didunoluwa Obilanade ◽  
Christo Dordlofva ◽  
Peter Törlind
Keyword(s):  
Surface Roughness ◽  
Additive Manufacturing ◽  
Literature Review ◽  
Future Research ◽  
Reduction Potentials ◽  
Research Fields ◽  
Post Process ◽  
Accessibility Issues ◽  
End Use ◽  
And Performance

AbstractOne often-cited benefit of using metal additive manufacturing (AM) is the possibility to design and produce complex geometries that suit the required function and performance of end-use parts. In this context, laser powder bed fusion (LPBF) is one suitable AM process. Due to accessibility issues and cost-reduction potentials, such ‘complex’ LPBF parts should utilise net-shape manufacturing with minimal use of post-process machining. The inherent surface roughness of LPBF could, however, impede part performance, especially from a structural perspective and in particular regarding fatigue. Engineers must therefore understand the influence of surface roughness on part performance and how to consider it during design. This paper presents a systematic literature review of research related to LPBF surface roughness. In general, research focuses on the relationship between surface roughness and LPBF build parameters, material properties, or post-processing. Research on design support on how to consider surface roughness during design for AM is however scarce. Future research on such supports is therefore important given the effects of surface roughness highlighted in other research fields.

scholarly journals 3D Printed Masks for Powders and Viruses Safety Protection Using Food Grade Polymers: Empirical Tests

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 617
Author(s):  
Ruben Foresti ◽  
Benedetta Ghezzi ◽  
Matteo Vettori ◽  
Lorenzo Bergonzi ◽  
Silvia Attolino ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Additive Manufacturing ◽  
Material Selection ◽  
Mechanical Resistance ◽  
Biological Safety ◽  
Fused Deposition ◽  
Industrial Grade ◽  
Safety Protection ◽  
3D Printed ◽  
Manufacturing Technologies

The production of 3D printed safety protection devices (SPD) requires particular attention to the material selection and to the evaluation of mechanical resistance, biological safety and surface roughness related to the accumulation of bacteria and viruses. We explored the possibility to adopt additive manufacturing technologies for the production of respirator masks, responding to the sudden demand of SPDs caused by the emergency scenario of the pandemic spread of SARS-COV-2. In this study, we developed different prototypes of masks, exclusively applying basic additive manufacturing technologies like fused deposition modeling (FDM) and droplet-based precision extrusion deposition (db-PED) to common food packaging materials. We analyzed the resulting mechanical characteristics, biological safety (cell adhesion and viability), surface roughness and resistance to dissolution, before and after the cleaning and disinfection phases. We showed that masks 3D printed with home-grade printing equipment have similar performances compared to the industrial-grade ones, and furthermore we obtained a perfect face fit by customizing their shape. Finally, we developed novel approaches to the additive manufacturing post-processing phases essential to assure human safety in the production of 3D printed custom medical devices.

scholarly journals Selective laser melting for improving quality characteristics of a prism shaped topology injection mould tool insert for the automotive industry

2021 ◽  
pp. 095440622198938
Author(s):  
Mennatallah F El Kashouty ◽  
Allan EW Rennie ◽  
Mootaz Ghazy ◽  
Ahmed Abd El Aziz
Keyword(s):  
Surface Roughness ◽  
Selective Laser Melting ◽  
Automotive Industry ◽  
Injection Moulding ◽  
Dimensional Accuracy ◽  
Quality Characteristics ◽  
Surface Topology ◽  
Laser Melting ◽  
Injection Mould ◽  
Tool Insert

Manufacturing process constraints and design complexities are the main challenges that face the aftermarket automotive industry. For that reason, recently, selective laser melting (SLM) is being recognised as a viable approach in the fabrication of injection moulding tool inserts. Due to its versatility, SLM technology is capable of producing freeform designs. For the first reported time, in this study SLM is recognized for its novel application in overcoming fabrication complexities for prism shaped topology of a vehicle headlamp’s reflector injection moulding tool insert. Henceforth, performance measures of the SLM-fabricated injection mould tool insert is assessed in comparison to a CNC-milled counterpart to improve quality characteristics. Tests executed and detailed in this paper are divided into two stages; the first stage assesses both fabricated tool inserts in terms of manufacturability; the second stage assesses the functionality of the end-products by measuring the surface roughness, dimensional accuracy and light reflectivity from the vehicle reflectors. The results obtained show that employing SLM technology can offer an effective and efficient alternative to subtractive manufacturing, successfully producing tool inserts with complex surface topology. Significant benefits in terms of surface roughness, dimensional accuracy and product functionality were achieved through the use of SLM technology. it was concluded that the SLM-fabricated inserts products proved to have relatively lower values of surface roughness in comparison to their CNC counterparts.

Influence of Metal Transfer Behavior Under Ar And CO2 Shielding Gases On Geometry And Surface Roughness of Single And Multilayer Structures In GMAW-Based Wire Arc Additive Manufacturing of Mild Steel

2021 ◽  
Author(s):  
Mitsugu Yamaguchi ◽  
Rikiya Komata ◽  
Tatsuaki Furumoto ◽  
Satoshi Abe ◽  
Akira Hosokawa
Keyword(s):  
Surface Roughness ◽  
Additive Manufacturing ◽  
Molten Pool ◽  
Multilayer Structure ◽  
Short Circuit ◽  
Metal Transfer ◽  
Geometric Accuracy ◽  
Transfer Behavior ◽  
Ar Gas ◽  
Wire Arc Additive Manufacturing

Abstract Wire arc additive manufacturing (WAAM) is advantageous for fabricating large-scale metallic components, however, a high geometric accuracy as that of other AM techniques cannot be achieved because of the deposition process with a large layer. This study focuses on the WAAM process based on gas metal arc welding (GMAW). To clarify the influence of shielding gas used to protect a molten metal during fabrication on the geometric accuracy of the built part obtained via the GMAW-based WAAM process, the influence of the metal transfer behavior on the geometry and surface roughness of the fabricated structures was investigated via visualization using a high-speed camera when single and multilayer depositions were performed under different heat inputs and gases. However, when using Ar gas, the heat flux from an arc to the workpiece is relatively low, limiting the depth of the molten pool during welding. The effect of its characteristics on the stair steps that are inevitably produced on the side face of the multilayer structure in the WAAM process was verified, and for a heat input of 1.17 kJ/cm under Ar gas, a higher geometric accuracy of the multilayer structure was obtained without interlayer cooling. The short circuit between the metal droplet and the fabricated surface, where the molten pool is insufficiently formed, resulted in a hump formation. Further, the metal transfer under Ar gas reduced the surface irregularities on the fabricated structure.

Additive manufacturing using fine wire-based laser metal deposition

2019 ◽  
Vol 26 (3) ◽  
pp. 473-483
Author(s):  
Muhammad Omar Shaikh ◽  
Ching-Chia Chen ◽  
Hua-Cheng Chiang ◽  
Ji-Rong Chen ◽  
Yi-Chin Chou ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Tensile Strength ◽  
Additive Manufacturing ◽  
High Precision ◽  
Surface Finish ◽  
Dimensional Accuracy ◽  
Laser Metal Deposition ◽  
Cross Sectional ◽  
Content Type ◽  
Fine Wire

Purpose Using wire as feedstock has several advantages for additive manufacturing (AM) of metal components, which include high deposition rates, efficient material use and low material costs. While the feasibility of wire-feed AM has been demonstrated, the accuracy and surface finish of the produced parts is generally lower than those obtained using powder-bed/-feed AM. The purpose of this study was to develop and investigate the feasibility of a fine wire-based laser metal deposition (FW-LMD) process for producing high-precision metal components with improved resolution, dimensional accuracy and surface finish. Design/methodology/approach The proposed FW-LMD AM process uses a fine stainless steel wire with a diameter of 100 µm as the additive material and a pulsed Nd:YAG laser as the heat source. The pulsed laser beam generates a melt pool on the substrate into which the fine wire is fed, and upon moving the X–Y stage, a single-pass weld bead is created during solidification that can be laterally and vertically stacked to create a 3D metal component. Process parameters including laser power, pulse duration and stage speed were optimized for the single-pass weld bead. The effect of lateral overlap was studied to ensure low surface roughness of the first layer onto which subsequent layers can be deposited. Multi-layer deposition was also performed and the resulting cross-sectional morphology, microhardness, phase formation, grain growth and tensile strength have been investigated. Findings An optimized lateral overlap of about 60-70% results in an average surface roughness of 8-16 µm along all printed directions of the X–Y stage. The single-layer thickness and dimensional accuracy of the proposed FW-LMD process was about 40-80 µm and ±30 µm, respectively. A dense cross-sectional morphology was observed for the multilayer stacking without any visible voids, pores or defects present between the layers. X-ray diffraction confirmed a majority austenite phase with small ferrite phase formation that occurs at the junction of the vertically stacked beads, as confirmed by the electron backscatter diffraction (EBSD) analysis. Tensile tests were performed and an ultimate tensile strength of about 700-750 MPa was observed for all samples. Furthermore, multilayer printing of different shapes with improved surface finish and thin-walled and inclined metal structures with a minimum achievable resolution of about 500 µm was presented. Originality/value To the best of the authors’ knowledge, this is the first study to report a directed energy deposition process using a fine metal wire with a diameter of 100 µm and can be a possible solution to improving surface finish and reducing the “stair-stepping” effect that is generally observed for wires with a larger diameter. The AM process proposed in this study can be an attractive alternative for 3D printing of high-precision metal components and can find application for rapid prototyping in a range of industries such as medical and automotive, among others.

ADDITIVE MANUFACTURING PARAMETERS OPTIMIZATION OF Ti6AL4V ELI FOR MEDICAL IMPLANTS

2022 ◽  
Author(s):  
VIJAY KUMAR MEENA ◽  
PARVEEN KALRA ◽  
RAVINDRA KUMAR SINHA
Keyword(s):  
Surface Roughness ◽  
Additive Manufacturing ◽  
Weight Ratio ◽  
High Strength ◽  
Surface Characteristics ◽  
Parameters Optimization ◽  
Medical Implants ◽  
Scan Speed ◽  
Grey Relational ◽  
Manufacturing Parameters

Additive manufacturing (AM) of titanium (Ti) alloys has always fascinated researchers owing to its high strength to weight ratio, biocompatibility, and anticorrosive properties, making Ti alloy an ideal candidate for medical applications. The aim of this paper is to optimize the AM parameters, such as Laser Power (LP), Laser Scan Speed (LSS), and Hatch Space (HS), using Analysis of Variance (ANOVA) and Grey Relational analysis (GRA) for mechanical and surface characteristics like hardness, surface roughness, and contact angle, of Ti6Al4V ELI considering medical implant applications. The input parameters are optimized to have optimum hardness, surface roughness and hydrophilicity required for medical implants.

Ti6Al4V Parts Produced by Electron Beam Melting: Analysis of Dimensional Accuracy and Surface Roughness

2020 ◽  
Vol 19 (01) ◽  
pp. 107-130 ◽  
Author(s):  
R. Borrelli ◽  
S. Franchitti ◽  
C. Pirozzi ◽  
L. Carrino ◽  
L. Nele ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Electron Beam ◽  
Additive Manufacturing ◽  
Electron Beam Melting ◽  
Complex Shape ◽  
Electron Beam Welding ◽  
Raw Materials ◽  
Dimensional Accuracy ◽  
High Energy ◽  
Quality Certification

Additive manufacturing (AM), applied to metal industry, is a family of processes that allows complex shape components to be realized from raw materials in the form of powders. Electron beam melting (EBM) is a relatively new additive manufacturing (AM) technology. Similar to electron-beam welding, EBM utilizes a high-energy electron beam as a moving heat source to melt metal powder, and 3D parts are produced in a layer-building fashion by rapid self-cooling. By EBM, it is possible to realize metallic complex shape components, e.g. fine network structures, internal cavities and channels, which are difficult to make by conventional manufacturing means. This feature is of particular interest in titanium industry in which numerous efforts are done to develop near net shape processes. In the field of mechanical engineering and, in particular, in the aerospace industry, it is crucial for quality certification purpose that components are produced through qualified and robust manufacturing processes ensuring high product repeatability. The contribution of the present work is to experimentally identify the EBM job parameters (sample orientation, location of the sample in the layer and height in the build chamber) that influence the dimensional accuracy and the surface roughness of the manufactured parts in Ti6Al4V. The repeatability of EBM is investigated too.

Sign in / Sign up

Export Citation Format

Share Document