Numerical study of the effects of cooling on evolution of unsteady disturbances and transition to turbulence in a boundary layer at flow mach number M = 6

2019 ◽  
Author(s):  
D. V. Khotyanovsky ◽  
S. P. Borisov ◽  
A. A. Shershnev ◽  
A. N. Kudryavtsev
Keyword(s):  
Boundary Layer ◽  
Mach Number ◽  
Numerical Study ◽  
Transition To Turbulence

Boundary Layer Suction via a Slot in a Transonic Compressor: Numerical Parameter Study and First Experiments

2004 ◽  
Author(s):  
K. Hubrich ◽  
A. Bo¨lcs ◽  
P. Ott
Keyword(s):  
Boundary Layer ◽  
Shock Wave ◽  
Mach Number ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Parameter Study ◽  
Flow Angle ◽  
Boundary Layer Suction ◽  
Transonic Compressor ◽  
Shock Mach Number

In the present paper a numerical and experimental study aiming at the enhancement of the working range of a transonic compressor via boundary layer suction (BLS) is presented. The main objective of the investigation is to study the influence of BLS on the interference between shock wave and boundary layer and to identify the possible benefit of BLS on the compressor working characteristics. An extensive numerical study has been carried out for the DATUM blade and for 2 different suction location configurations for one speed line and varying back-pressure levels, ranging from choked conditions to stall. It was found that the working range of the transonic compressor with a nominal inlet Mach number of 1.2 and a nominal pre-shock Mach number of 1.35 could be increased by sucking 2% of flow on the SS away, in such a way that the maximum pressure ratio and maximum diffusion could both be increased by 10%, when compared to the DATUM case. For smaller pressure ratios with respect to the design pressure ratio, the BLS is located in a supersonic flow region and thus creates additional losses due to a more divergent flow channel, which additionally accelerates the flow and results in a higher pre-shock Mach number creating higher losses. First measurements carried out in LTTs annular cascade, do show reasonable agreement with the computations in terms of inlet Mach number, flow angle, main shock location and stall limit. The most pronounced difference between measurements and computations is the occurrence of a terminal normal channel shock behind a bowed detached shock wave and a separation on the SS of the blade, which were both not predicted by the CFD.

On ramped vanes to control normal shock boundary layer interactions

2018 ◽  
Vol 122 (1256) ◽  
pp. 1568-1585 ◽  
Author(s):  
S. Lee ◽  
E. Loth
Keyword(s):  
Boundary Layer ◽  
Mach Number ◽  
Flow Control ◽  
Flow Separation ◽  
Shape Factor ◽  
Incompressible Flows ◽  
Numerical Study ◽  
Normal Shock ◽  
Wall Region ◽  
Literature Study

ABSTRACTA novel vortex generator design positioned upstream of a normal shock followed by a subsequent diffuser was investigated using large eddy simulations. In particular, “ramped-vane” flow control devices with three different heights relative to the incoming boundary layer thickness (0.34δ, 0.52δ and 0·75δ) were placed in a supersonic boundary layer with a freestream Mach number of 1.3 and a Reynolds number of 2400 based on the momentum thickness. This is the first numerical study to investigate the size effect of the ramped-vane for flow control device in terms of shape factor, flow separation and flow unsteadiness. The results showed that these devices generated strong streamwise vortices that entrained high-momentum fluid to the near-wall region and increased turbulent mixing. The devices also decreased shock-induced flow separation, which resulted in a higher downstream skin friction in the diffuser. In general, the largest ramped-vane (0.75δ) produced the largest reductions in flow separation, shape factor and overall unsteadiness. These results and a careful review of the literature study also determined the quantitative correlation of optimum VG height with Mach number, wherebyh/δ~1 is often optimum for incompressible flows while higher Mach numbers lead to small optimum heights, tending towards h/δ~0.45 atM=2.5.

EXPERIMENTAL INVESTIGATION OF FLOW RESPONSE TO STATIONARY DISTURBANCE IN ROTATING-DISK FLOW

2019 ◽  
Vol XVI (2) ◽  
pp. 13-22
Author(s):  
Muhammad Ehtisham Siddiqui
Keyword(s):  
Boundary Layer ◽  
Boundary Layer Flow ◽  
Three Dimensional ◽  
Rotating Disk ◽  
Careful Analysis ◽  
Laboratory Frame ◽  
Transition To Turbulence ◽  
Turbulent Regime ◽  
Mean Velocity ◽  
Layer Flow

Three-dimensional boundary-layer flow is well known for its abrupt and sharp transition from laminar to turbulent regime. The presented study is a first attempt to achieve the target of delaying the natural transition to turbulence. The behaviour of two different shaped and sized stationary disturbances (in the laboratory frame) on the rotating-disk boundary layer flow is investigated. These disturbances are placed at dimensionless radial location (Rf = 340) which lies within the convectively unstable zone over a rotating-disk. Mean velocity profiles were measured using constant-temperature hot-wire anemometry. By careful analysis of experimental data, the instability of these disturbance wakes and its estimated orientation within the boundary-layer were investigated.

scholarly journals Shock-induced heating and transition to turbulence in a hypersonic boundary layer

2020 ◽  
Vol 909 ◽  
Author(s):  
Lin Fu ◽  
Michael Karp ◽  
Sanjeeb T. Bose ◽  
Parviz Moin ◽  
Javier Urzay
Keyword(s):  
Boundary Layer ◽  
Transition To Turbulence ◽  
Hypersonic Boundary Layer

Abstract

scholarly journals Development of Depth-Limited Wave Boundary Layers over a Smooth Bottom

2020 ◽  
Vol 9 (1) ◽  
pp. 27
Author(s):  
Hitoshi Tanaka ◽  
Nguyen Xuan Tinh ◽  
Xiping Yu ◽  
Guangwei Liu
Keyword(s):  
Numerical Simulation ◽  
Boundary Layer ◽  
Boundary Layers ◽  
Wave Motion ◽  
Numerical Study ◽  
Experiment Data ◽  
Tidal Motion ◽  
Long Period ◽  
Simulation Results ◽  
Wave Boundary

A theoretical and numerical study is carried out to investigate the transformation of the wave boundary layer from non-depth-limited (wave-like boundary layer) to depth-limited one (current-like boundary layer) over a smooth bottom. A long period of wave motion is not sufficient to induce depth-limited properties, although it has simply been assumed in various situations under long waves, such as tsunami and tidal currents. Four criteria are obtained theoretically for recognizing the inception of the depth-limited condition under waves. To validate the theoretical criteria, numerical simulation results using a turbulence model as well as laboratory experiment data are employed. In addition, typical field situations induced by tidal motion and tsunami are discussed to show the usefulness of the proposed criteria.

Sign in / Sign up

Export Citation Format

Share Document