scholarly journals Hole-doped M4SiTe4 (M = Ta, Nb) as an efficient p-type thermoelectric material for low-temperature applications

2019 ◽  
Vol 115 (4) ◽  
pp. 043901 ◽  
Author(s):  
Yoshihiko Okamoto ◽  
Yuma Yoshikawa ◽  
Taichi Wada ◽  
Koshi Takenaka
ChemInform ◽  
2010 ◽  
Vol 31 (22) ◽  
pp. no-no
Author(s):  
Duck-Young Chung ◽  
Tim Hogan ◽  
Paul Brazis ◽  
Melissa Rocci-Lane ◽  
Carl Kannewurf ◽  
...  

2020 ◽  
Vol 26 (S2) ◽  
pp. 2916-2917
Author(s):  
Luis Laguna Zubia ◽  
C.G. Garay-Reyes ◽  
M.A. Ruiz-Esparza-Rodriguez ◽  
J.M. Mendoza-Duarte ◽  
Ivanovich Estrada ◽  
...  

2021 ◽  
Vol 13 (1) ◽  
Author(s):  
Muhammad Naqi ◽  
Kyung Hwan Choi ◽  
Hocheon Yoo ◽  
Sudong Chae ◽  
Bum Jun Kim ◽  
...  

AbstractLow-temperature-processed semiconductors are an emerging need for next-generation scalable electronics, and these semiconductors need to feature large-area fabrication, solution processability, high electrical performance, and wide spectral optical absorption properties. Although various strategies of low-temperature-processed n-type semiconductors have been achieved, the development of high-performance p-type semiconductors at low temperature is still limited. Here, we report a unique low-temperature-processed method to synthesize tellurium nanowire networks (Te-nanonets) over a scalable area for the fabrication of high-performance large-area p-type field-effect transistors (FETs) with uniform and stable electrical and optical properties. Maximum mobility of 4.7 cm2/Vs, an on/off current ratio of 1 × 104, and a maximum transconductance of 2.18 µS are achieved. To further demonstrate the applicability of the proposed semiconductor, the electrical performance of a Te-nanonet-based transistor array of 42 devices is also measured, revealing stable and uniform results. Finally, to broaden the applicability of p-type Te-nanonet-based FETs, optical measurements are demonstrated over a wide spectral range, revealing an exceptionally uniform optical performance.


Author(s):  
Masanori Tashiro ◽  
Sohei Sukenaga ◽  
Koichi Ikemoto ◽  
Kozo Shinoda ◽  
Tsuyoshi Kajitani ◽  
...  

MRS Advances ◽  
2020 ◽  
Vol 5 (10) ◽  
pp. 481-487 ◽  
Author(s):  
Norifusa Satoh ◽  
Masaji Otsuka ◽  
Yasuaki Sakurai ◽  
Takeshi Asami ◽  
Yoshitsugu Goto ◽  
...  

ABSTRACTWe examined a working hypothesis of sticky thermoelectric (TE) materials, which is inversely designed to mass-produce flexible TE sheets with lamination or roll-to-roll processes without electric conductive adhesives. Herein, we prepared p-type and n-type sticky TE materials via mixing antimony and bismuth powders with low-volatilizable organic solvents to achieve a low thermal conductivity. Since the sticky TE materials are additionally injected into punched polymer sheets to contact with the upper and bottom electrodes in the fabrication process, the sticky TE modules of ca. 2.4 mm in thickness maintained temperature differences of ca. 10°C and 40°C on a hot plate of 40 °C and 120°C under a natural-air cooling condition with a fin. In the single-cell resistance analysis, we found that 75∼150-µm bismuth powder shows lower resistance than the smaller-sized one due to the fewer number of particle-particle interfaces in the electric pass between the upper and bottom electrodes. After adjusting the printed wiring pattern for the upper and bottom electrodes, we achieved 42 mV on a hot plate (120°C) with the 6 x 6 module having 212 Ω in the total resistance. In addition to the possibility of mass production at a reasonable cost, the sticky TE materials provide a low thermal conductivity for flexible TE modules to capture low-temperature waste heat under natural-air cooling conditions with fins for the purpose of energy harvesting.


Sign in / Sign up

Export Citation Format

Share Document