Finite-element model for an Al+2.38% Cu+0.06% SiC composite with regard to its structural components

2017 ◽  
Author(s):  
Sergey Voronin ◽  
Michail Ledyaev ◽  
Pavel Loboda ◽  
Sergey Konovalov
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Structural Components

A Review of In-Place Design Approaches for Spar Hulls

2005 ◽  
Author(s):  
Cheng-Yo Chen ◽  
Trevor Mills
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Current Practice ◽  
State Of The Art ◽  
Element Model ◽  
Maximum Strength ◽  
Design Approach ◽  
Structural Components ◽  
Advantages And Disadvantages ◽  
Design Loads

This paper reviews the current practice for the in-place design of Spar hulls. Both the commonly-used approach and the state-of-the-art procedure for the maximum strength and fatigue conditions will be presented. Key assumptions for various design approaches will be discussed along with advantages and disadvantages of each approach. The review will focus on how each approach generates hydrodynamic loadings, performs global motions analysis, and maps design loads from motion analyses to structural finite-element model. Important aspects relating to Spar design will be addressed. In particular, effect of vortex induced hull motions (VIM) will be discussed, and an approach for including the VIM effect in the design of moorings and risers will also be described. Impact on the maximum strength and fatigue capacity of critical structural components due to the assumptions employed in the commonly-used design approach will be evaluated and quantified as compared to the results from the more rigorous state-of-the-art approach.

Finite Element Simulation of Tire-Rim Interface

1989 ◽  
Vol 17 (4) ◽  
pp. 305-325 ◽  
Author(s):  
N. T. Tseng ◽  
R. G. Pelle ◽  
J. P. Chang
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Finite Element Simulation ◽  
Contact Pressure ◽  
Element Model ◽  
Experimental Measurements ◽  
Inflation Pressure ◽  
Interference Fit ◽  
Element Simulation ◽  
Rubber Composite

Abstract A finite element model was developed to simulate the tire-rim interface. Elastomers were modeled by nonlinear incompressible elements, whereas plies were simulated by cord-rubber composite elements. Gap elements were used to simulate the opening between tire and rim at zero inflation pressure. This opening closed when the inflation pressure was increased gradually. The predicted distribution of contact pressure at the tire-rim interface agreed very well with the available experimental measurements. Several variations of the tire-rim interference fit were analyzed.

Torsional Analysis of a Steel Cord-Rubber Tire Belt Structure

1996 ◽  
Vol 24 (4) ◽  
pp. 339-348 ◽  
Author(s):  
R. M. V. Pidaparti
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Composite Structures ◽  
Three Dimensional ◽  
Element Model ◽  
Torsional Stiffness ◽  
Element Analysis ◽  
Rubber Belt ◽  
Steel Cord ◽  
Torsional Analysis

Abstract A three-dimensional (3D) beam finite element model was developed to investigate the torsional stiffness of a twisted steel-reinforced cord-rubber belt structure. The present 3D beam element takes into account the coupled extension, bending, and twisting deformations characteristic of the complex behavior of cord-rubber composite structures. The extension-twisting coupling due to the twisted nature of the cords was also considered in the finite element model. The results of torsional stiffness obtained from the finite element analysis for twisted cords and the two-ply steel cord-rubber belt structure are compared to the experimental data and other alternate solutions available in the literature. The effects of cord orientation, anisotropy, and rubber core surrounding the twisted cords on the torsional stiffness properties are presented and discussed.

Sign in / Sign up

Export Citation Format

Share Document