Structure of electrolytic nickel–molybdenum alloys after deposition and heat treatment

2017 ◽  
Author(s):  
I. M. Kovenskiy ◽  
A. A. Kulemina
Keyword(s):  
Heat Treatment ◽  
Electrolytic Nickel ◽  
Molybdenum Alloys

Effect of molybdenum and heat treatment on corrosion properties of nickel-molybdenum alloys

1975 ◽  
Vol 17 (2) ◽  
pp. 144-148
Author(s):  
L. V. Gernets ◽  
S. A. Golovanenko ◽  
T. V. Svistunova
Keyword(s):  
Heat Treatment ◽  
Corrosion Properties ◽  
Molybdenum Alloys

Microconstituents in Chromium-Base Chromium-Iron-Molybdenum Alloys and Their Behavior with Heat Treatment

JOM ◽  
1952 ◽  
Vol 4 (12) ◽  
pp. 1329-1342
Author(s):  
Joseph P. Hammond ◽  
Arthur B. Westerman ◽  
Howard C. Cross
Keyword(s):  
Heat Treatment ◽  
Molybdenum Alloys

Production of sintered deformable (wrought) nickel-molybdenum alloys. II. Structure and mechanical properties of alloys after hot plastic working and heat treatment

1983 ◽  
Vol 22 (5) ◽  
pp. 368-372
Author(s):  
Yu. V. Voronin ◽  
Zh. I. Dzneladze ◽  
R. P. Shchegoleva ◽  
T. V. Svistunova ◽  
Z. K. Runova ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Plastic Working ◽  
Molybdenum Alloys

The Precipitation of Si in AlCuSi Thin Films

1973 ◽  
Vol 31 ◽  
pp. 34-35 ◽  
Author(s):  
R. M. Anderson
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Heat Treatment ◽  
Solid Solution ◽  
Integrated Circuit ◽  
Copper Film ◽  
Solution Concentration ◽  
X Ray ◽  
Silicon Thin Films ◽  
Before And After

Aluminum-copper-silicon thin films have been considered as an interconnection metallurgy for integrated circuit applications. Various schemes have been proposed to incorporate small percent-ages of silicon into films that typically contain two to five percent copper. We undertook a study of the total effect of silicon on the aluminum copper film as revealed by transmission electron microscopy, scanning electron microscopy, x-ray diffraction and ion microprobe techniques as a function of the various deposition methods.X-ray investigations noted a change in solid solution concentration as a function of Si content before and after heat-treatment. The amount of solid solution in the Al increased with heat-treatment for films with ≥2% silicon and decreased for films <2% silicon.

The influence of heat treatment on the fiber/matrix interface in a SiC-reinforced glassceramic

1988 ◽  
Vol 46 ◽  
pp. 742-743
Author(s):  
E. Bischoff ◽  
O. Sbaizero
Keyword(s):  
Heat Treatment ◽  
Aluminum Silicate ◽  
Lithium Aluminum ◽  
Interfacial Region ◽  
Specimen Preparation ◽  
Crack Wake ◽  
Pull Out ◽  
Annealed Material ◽  
Ultrasonic Drilling ◽  
Fiber Matrix Interface

Fiber or whisker reinforced ceramics show improved toughness and strength. Bridging by intact fibers in the crack wake and fiber pull-out after failure contribute to the additional toughness. These processes are strongly influenced by the sliding and debonding resistance of the interfacial region. The present study examines the interface in a laminated 0/90 composite consisting of SiC (Nicalon) fibers in a lithium-aluminum-silicate (LAS) glass-ceramic matrix. The material shows systematic changes in sliding resistance upon heat treatment.As-processed samples were annealed in air at 800 °C for 2, 4, 8, 16 and 100 h, and for comparison, in helium at 800 °C for 4 h. TEM specimen preparation of as processed and annealed material was performed with special care by cutting along directions having the fibers normal and parallel to the section plane, ultrasonic drilling, dimpling to 100 pm and final ionthinning. The specimen were lightly coated with Carbon and examined in an analytical TEM operated at 200 kV.

Strain-induced martensite effects on transgranular carbide precipitation in type 304 stainless steels

1991 ◽  
Vol 49 ◽  
pp. 604-605
Author(s):  
A.H. Advani ◽  
L.E. Murr ◽  
D. Matlock
Keyword(s):  
Heat Treatment ◽  
Grain Boundary ◽  
Stress Corrosion Cracking ◽  
Stainless Steels ◽  
Deformation Twin ◽  
Austenitic Stainless Steels ◽  
Carbide Precipitation ◽  
Strain Induced Martensite ◽  
Type 304

Thermomechanically induced strain is a key variable producing accelerated carbide precipitation, sensitization and stress corrosion cracking in austenitic stainless steels (SS). Recent work has indicated that higher levels of strain (above 20%) also produce transgranular (TG) carbide precipitation and corrosion simultaneous with the grain boundary phenomenon in 316 SS. Transgranular precipitates were noted to form primarily on deformation twin-fault planes and their intersections in 316 SS.Briant has indicated that TG precipitation in 316 SS is significantly different from 304 SS due to the formation of strain-induced martensite on 304 SS, though an understanding of the role of martensite on the process has not been developed. This study is concerned with evaluating the effects of strain and strain-induced martensite on TG carbide precipitation in 304 SS. The study was performed on samples of a 0.051%C-304 SS deformed to 33% followed by heat treatment at 670°C for 1 h.

Sign in / Sign up

Export Citation Format

Share Document