Evaluation of transition-sensitive eddy-viscosity turbulence models for separated flow in OpenFOAM

2017 ◽  
Author(s):  
H. Fadhila ◽  
H. Medina ◽  
A. Beechook ◽  
S. Aleksandrova ◽  
S. Benjamin
Keyword(s):  
Eddy Viscosity ◽  
Turbulence Models ◽  
Separated Flow

High Resolution Overset Structured Grid RANS Simulations of Flow Past a Surface Mounted Cube Using Eddy Viscosity Closure Models

2018 ◽  
Author(s):  
Marc C. Goldbach ◽  
Mesbah Uddin
Keyword(s):  
Eddy Viscosity ◽  
Complex Structure ◽  
Flow Characteristics ◽  
Turbulence Models ◽  
Separated Flow ◽  
Industrial Applications ◽  
Separated Flows ◽  
Transitional Flow ◽  
Stream Velocity ◽  
Mean Flow

While Reynolds-averaged simulatons (RAS) have found success in the evaluation of many canonical shear flows, and moderately separated flows, their application to highly separated flows have shown notable deficiencies. This study aims to investigate these deficiencies in the eddy-viscosity formulation of four commonly used turbulence models under separated flow in an attempt to aid in the improved formulation of such models. Analyses are performed on the flow field around a wall mounted cube at a Reynolds number of 40,000 based on the cube height, h, and free stream velocity, U0. While a common occurrence in industrial applications, this type of flow constitutes a complex structure exhibiting a large separated wake region, high anisotropy, and multiple vortex structures. As well, interactions between vortices developed off of different faces of the cube significantly alter the overall flow characteristics, posing a significant challenge for the commonly used industrial turbulence models. Comparison of mean flow characteristics show remarkable agreement between experimental values and turbulence models which are capable of predicting transitional flow. Evaluation of turbulence parameters show the general underestimation of Reynolds stress for transitional models, while fully turbulent models show this value to be overestimated, resulting in completely disparate representations of mean flow structures between the two classes of models (transitional and fully turbulent).

High-Resolution RANS Simulations of Flow Past a Surface-Mounted Cube Using Eddy-Viscosity Closure Models

2019 ◽  
Vol 4 (1) ◽  
Author(s):  
Marc C. Goldbach ◽  
Mesbah Uddin
Keyword(s):  
Eddy Viscosity ◽  
Complex Structure ◽  
Flow Characteristics ◽  
Turbulence Models ◽  
Separated Flow ◽  
Industrial Applications ◽  
Separated Flows ◽  
Transitional Flow ◽  
Mean Flow ◽  
Freestream Velocity

Abstract While Reynolds-averaged simulations have found success in the evaluation of many canonical shear flows and moderately separated flows, their application to highly separated flows have shown notable deficiencies. This study aimed to investigate these deficiencies in the eddy-viscosity formulation of four commonly used turbulence models under separated flow in an attempt to aid in the improved formulation of such models. Analyses are performed on the flow field around a wall-mounted cube (WMC) at a Reynolds number of 40,000 based on the cube height, h, and freestream velocity, U0. While a common occurrence in industrial applications, this type of flow constitutes a complex structure exhibiting a large separated wake region, high anisotropy, and multiple vortex structures. As well, interactions between vortices developed off of different faces of the cube significantly alter the overall flow characteristics, posing a significant challenge for the commonly used industrial turbulence models. Comparison of mean flow characteristics show remarkable agreement between experimental values and turbulence models which are capable of predicting transitional flow. Evaluation of turbulence parameters show the general underestimation of Reynolds stress for transitional models, while fully turbulent models show this value to be overestimated, resulting in completely disparate representations of mean flow structures between the two classes of models (transitional and fully turbulent).

Improving predictions of heat transfer in indoor environments with eddy viscosity turbulence models

2015 ◽  
Vol 9 (2) ◽  
pp. 213-220 ◽  
Author(s):  
Christian Heschl ◽  
Yao Tao ◽  
Kiao Inthavong ◽  
Jiyuan Tu
Keyword(s):  
Heat Transfer ◽  
Eddy Viscosity ◽  
Turbulence Models ◽  
Indoor Environments

Assessment of turbulence models using DNS data of compressible plane free shear layer flow

2021 ◽  
Vol 931 ◽  
Author(s):  
D. Li ◽  
J. Komperda ◽  
A. Peyvan ◽  
Z. Ghiasi ◽  
F. Mashayek
Keyword(s):  
Shear Layer ◽  
Compressible Flows ◽  
Eddy Viscosity ◽  
Turbulence Models ◽  
Correlation Coefficients ◽  
Free Shear Layer ◽  
Smagorinsky Model ◽  
Reynolds Analogy ◽  
Velocity Fluctuations ◽  
Scale Similarity

The present paper uses the detailed flow data produced by direct numerical simulation (DNS) of a three-dimensional, spatially developing plane free shear layer to assess several commonly used turbulence models in compressible flows. The free shear layer is generated by two parallel streams separated by a splitter plate, with a naturally developing inflow condition. The DNS is conducted using a high-order discontinuous spectral element method (DSEM) for various convective Mach numbers. The DNS results are employed to provide insights into turbulence modelling. The analyses show that with the knowledge of the Reynolds velocity fluctuations and averages, the considered strong Reynolds analogy models can accurately predict temperature fluctuations and Favre velocity averages, while the extended strong Reynolds analogy models can correctly estimate the Favre velocity fluctuations and the Favre shear stress. The pressure–dilatation correlation and dilatational dissipation models overestimate the corresponding DNS results, especially with high compressibility. The pressure–strain correlation models perform excellently for most pressure–strain correlation components, while the compressibility modification model gives poor predictions. The results of an a priori test for subgrid-scale (SGS) models are also reported. The scale similarity and gradient models, which are non-eddy viscosity models, can accurately reproduce SGS stresses in terms of structure and magnitude. The dynamic Smagorinsky model, an eddy viscosity model but based on the scale similarity concept, shows acceptable correlation coefficients between the DNS and modelled SGS stresses. Finally, the Smagorinsky model, a purely dissipative model, yields low correlation coefficients and unacceptable accumulated errors.

Simulation of Multi-Stage Compressor at Off-Design Conditions

2017 ◽  
Author(s):  
Feng Wang ◽  
Mauro Carnevale ◽  
Luca di Mare ◽  
Simon Gallimore
Keyword(s):  
Mass Flow ◽  
High Speed ◽  
Eddy Viscosity ◽  
Turbulence Models ◽  
Viscosity Model ◽  
Eddy Viscosity Model ◽  
Multi Stage ◽  
Pressure Profiles ◽  
Non Linear ◽  
The Right

Computational Fluid Dynamics (CFD) has been widely used for compressor design, yet the prediction of performance and stage matching for multi-stage, high-speed machines remain challenging. This paper presents the authors’ effort to improve the reliability of CFD in multistage compressor simulations. The endwall features (e.g. blade fillet and shape of the platform edge) are meshed with minimal approximations. Turbulence models with linear and non-linear eddy viscosity models are assessed. The non-linear eddy viscosity model predicts a higher production of turbulent kinetic energy in the passages, especially close to the endwall region. This results in a more accurate prediction of the choked mass flow and the shape of total pressure profiles close to the hub. The non-linear viscosity model generally shows an improvement on its linear counterparts based on the comparisons with the rig data. For geometrical details, truncated fillet leads to thicker boundary layer on the fillet and reduced mass flow and efficiency. Shroud cavities are found to be essential to predict the right blockage and the flow details close to the hub. At the part speed the computations without the shroud cavities fail to predict the major flow features in the passage and this leads to inaccurate predictions of massflow and shapes of the compressor characteristic. The paper demonstrates that an accurate representation of the endwall geometry and an effective turbulence model, together with a good quality and sufficiently refined grid result in a credible prediction of compressor matching and performance with steady state mixing planes.

Temperature Corrected Turbulence Model for High Temperature Jet Flow

2004 ◽  
Vol 126 (5) ◽  
pp. 844-850 ◽  
Author(s):  
Khaled S. Abdol-Hamid ◽  
S. Paul Pao ◽  
Steven J. Massey ◽  
Alaa Elmiligui
Keyword(s):  
High Temperature ◽  
Turbulence Model ◽  
Room Temperature ◽  
Eddy Viscosity ◽  
Mixing Layer ◽  
Supersonic Jet ◽  
Turbulence Models ◽  
Jet Flows ◽  
Viscosity Term ◽  
Mixing Layer Flows

It is well known that the two-equation turbulence models under-predict mixing in the shear layer for high temperature jet flows. These turbulence models were developed and calibrated for room temperature, low Mach number, and plane mixing layer flows. In the present study, four existing modifications to the two-equation turbulence model are implemented in PAB3D and their effect is assessed for high temperature jet flows. In addition, a new temperature gradient correction to the eddy viscosity term is tested and calibrated. The new model was found to be in the best agreement with experimental data for subsonic and supersonic jet flows at both low and high temperatures.

Evaluation of Turbulence Models Using Direct Numerical and Large-Eddy Simulation Data

2011 ◽  
Vol 133 (2) ◽  
Author(s):  
Hassan Raiesi ◽  
Ugo Piomelli ◽  
Andrew Pollard
Keyword(s):  
Boundary Layer ◽  
Large Eddy Simulation ◽  
Eddy Viscosity ◽  
Predictive Accuracy ◽  
Turbulence Models ◽  
Special Treatment ◽  
Two Dimensional ◽  
Square Duct ◽  
Eddy Simulation ◽  
Large Eddy

The performance of some commonly used eddy-viscosity turbulence models has been evaluated using direct numerical simulation (DNS) and large-eddy simulation (LES) data. Two configurations have been tested, a two-dimensional boundary layer undergoing pressure-driven separation, and a square duct. The DNS and LES were used to assess the k−ε, ζ−f, k−ω, and Spalart–Allmaras models. For the two-dimensional separated boundary layer, anisotropic effects are not significant and the eddy-viscosity assumption works well. However, the near-wall treatment used in k−ε models was found to have a critical effect on the predictive accuracy of the model (and, in particular, of separation and reattachment points). None of the wall treatments tested resulted in accurate prediction of the flow field. Better results were obtained with models that do not require special treatment in the inner layer (ζ−f, k−ω, and Spalart–Allmaras models). For the square duct calculation, only a nonlinear constitutive relation was found to be able to capture the secondary flow, giving results in agreement with the data. Linear models had significant error.

Sign in / Sign up

Export Citation Format

Share Document