scholarly journals Heat transfer in moving bed heat exchangers for high temperature thermal energy storage

2017 ◽  
Author(s):  
Philipp Bartsch ◽  
Stefan Zunft
Keyword(s):  
Heat Transfer ◽  
High Temperature ◽  
Energy Storage ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Heat Exchangers ◽  
Moving Bed

Thermal Analysis of Elemental Sulfur in a Shell-and-Tube Configuration for Thermal Energy Storage Applications

2016 ◽  
Author(s):  
Mitchell Shinn ◽  
Karthik Nithyanandam ◽  
Amey Barde ◽  
Richard Wirz
Keyword(s):  
Heat Transfer ◽  
High Temperature ◽  
Energy Storage ◽  
Numerical Model ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Elemental Sulfur ◽  
Low Cost ◽  
High Energy ◽  
Shell And Tube

Currently, concentrated solar power (CSP) plants utilize thermal energy storage (TES) in order to store excess energy so that it can later be dispatched during periods of intermittency or during times of high energy demand. Elemental sulfur is a promising candidate storage fluid for high temperature TES systems due to its high thermal mass, moderate vapor pressure, high thermal stability, and low cost. The objective of this paper is to investigate the behavior of encapsulated sulfur in a shell and tube configuration. An experimentally validated, transient, two-dimensional numerical model of the shell and tube TES system is presented. Initial results from both experimental and numerical analysis show high heat transfer performance of sulfur. The numerical model is then used to analyze the dynamic response of the elemental sulfur based TES system for multiple charging and discharging cycles. A sensitivity analysis is performed to analyze the effect of geometry (system length), cutoff temperature, and heat transfer fluid on the overall utilization of energy stored within this system. Overall, this paper demonstrates a systematic parametric study of a novel low cost, high performance TES system based on elemental sulfur as the storage fluid that can be utilized for different high temperature applications.

Investigation of a High-Temperature Packed-Bed Sensible Heat Thermal Energy Storage System With Large-Sized Elements

2013 ◽  
Vol 135 (4) ◽  
Author(s):  
Sarada Kuravi ◽  
Jamie Trahan ◽  
Yogi Goswami ◽  
Chand Jotshi ◽  
Elias Stefanakos ◽  
...  
Keyword(s):  
Heat Transfer ◽  
High Temperature ◽  
Energy Storage ◽  
Flow Rate ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Packed Bed ◽  
Inlet Temperature ◽  
Prototype System ◽  
Sensible Heat

A high-temperature, sensible heat thermal energy storage (TES) system is designed for use in a central receiver concentrating solar power plant. Air is used as the heat transfer fluid and solid bricks made out of a high storage density material are used for storage. Experiments were performed using a laboratory-scale TES prototype system, and the results are presented. The air inlet temperature was varied between 300 °C to 600 °C, and the flow rate was varied from 50 cubic feet per minute (CFM) to 90 CFM. It was found that the charging time decreases with increase in mass flow rate. A 1D packed-bed model was used to simulate the thermal performance of the system and was validated with the experimental results. Unsteady 1D energy conservation equations were formulated for combined convection and conduction heat transfer and solved numerically for charging/discharging cycles. Appropriate heat transfer and pressure drop correlations from prior literature were identified. A parametric study was done by varying the bed dimensions, fluid flow rate, particle diameter, and porosity to evaluate the charging/discharging characteristics, overall thermal efficiency, and capacity ratio of the system.

Heat Transfer in a High-Temperature Packed Bed Thermal Energy Storage System—Roles of Radiation and Intraparticle Conduction

1996 ◽  
Vol 118 (1) ◽  
pp. 50-57 ◽  
Author(s):  
A. A. Jalalzadeh-Azar ◽  
W. G. Steele ◽  
G. A. Adebiyi
Keyword(s):  
Heat Transfer ◽  
High Temperature ◽  
Energy Storage ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Storage System ◽  
Packed Bed ◽  
Energy Storage System ◽  
Operating Conditions ◽  
Thermal Energy Storage System

A model is developed and experimentally verified to study the heat transfer in a high-temperature packed bed thermal energy storage system utilizing zirconium oxide pellets. The packed bed receives flue gas at elevated temperatures varying with time during the storage process and utilizes air for the recovery process. Both convection and radiation are included in the model of the total heat transfer between the gas and the pellets. It is found that thermal radiation and intraparticle conduction do not play a major role in the overall heat transfer in the packed bed under the specified operating conditions. An uncertainty analysis is performed to investigate the propagation of the uncertainties in the variables to the overall uncertainty in the model predictions and the experimental results.

Sign in / Sign up

Export Citation Format

Share Document