scholarly journals Effect of sand and moisture on molten salt properties for open direct absorption solar receiver/storage system

2016 ◽  
Author(s):  
M. S. AlQaydi ◽  
T. Delclos ◽  
S. AlMheiri ◽  
T. McKrell ◽  
N. Calvet
Keyword(s):  
Molten Salt ◽  
Storage System ◽  
Direct Absorption ◽  
Solar Receiver

Conceptual design of porous volumetric solar receiver using molten salt as heat transfer fluid

2021 ◽  
Vol 301 ◽  
pp. 117400
Author(s):  
Shen Du ◽  
Ming-Jia Li ◽  
Ya-Ling He ◽  
Sheng Shen
Keyword(s):  
Heat Transfer ◽  
Molten Salt ◽  
Conceptual Design ◽  
Heat Transfer Fluid ◽  
Solar Receiver

Dynamic simulation of two-tank indirect thermal energy storage system with molten salt

2017 ◽  
Vol 113 ◽  
pp. 1311-1319 ◽  
Author(s):  
Xiaolei Li ◽  
Ershu Xu ◽  
Shuang Song ◽  
Xiangyan Wang ◽  
Guofeng Yuan
Keyword(s):  
Energy Storage ◽  
Molten Salt ◽  
Dynamic Simulation ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Storage System ◽  
Energy Storage System ◽  
Thermal Energy Storage System

Computational Analysis of a Pipe Flow Distributor for a Thermocline Based Thermal Energy Storage System

2013 ◽  
Vol 136 (2) ◽  
Author(s):  
Samia Afrin ◽  
Vinod Kumar ◽  
Desikan Bharathan ◽  
Greg C. Glatzmaier ◽  
Zhiwen Ma
Keyword(s):  
Energy Storage ◽  
Molten Salt ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Computational Analysis ◽  
Storage System ◽  
Flow Distribution ◽  
Energy Storage System ◽  
Heat Transfer Fluid ◽  
Case Scenario

The overall efficiency of a concentrating solar power (CSP) plant depends on the effectiveness of thermal energy storage (TES) system (Kearney and Herrmann, 2002, “Assessment of a Molten Salt Heat Transfer Fluid,” ASME). A single tank TES system consists of a thermocline region which produces the temperature gradient between hot and cold storage fluid by density difference (Energy Efficiency and Renewable Energy, http://www.eere.energy.gov/basics/renewable_energy/thermal_storage.html). Preservation of this thermocline region in the tank during charging and discharging cycles depends on the uniformity of the velocity profile at any horizontal plane. Our objective is to maximize the uniformity of the velocity distribution using a pipe-network distributor by varying the number of holes, distance between the holes, position of the holes and number of distributor pipes. For simplicity, we consider that the diameter of the inlet, main pipe, the distributor pipes and the height and the width of the tank are constant. We use Hitec® molten salt as the storage medium and the commercial software Gambit 2.4.6 and Fluent 6.3 for the computational analysis. We analyze the standard deviation in the velocity field and compare the deviations at different positions of the tank height for different configurations. Since the distance of the holes from the inlet and their respective arrangements affects the flow distribution throughout the tank; we investigate the impacts of rearranging the holes position on flow distribution. Impact of the number of holes and distributor pipes are also analyzed. We analyze our findings to determine a configuration for the best case scenario.

scholarly journals Performance Investigation of High Temperature Application of Molten Solar Salt Nanofluid in a Direct Absorption Solar Collector

Molecules ◽  
2019 ◽  
Vol 24 (2) ◽  
pp. 285 ◽  
Author(s):  
M. Karim ◽  
Owen Arthur ◽  
Prasad Yarlagadda ◽  
Majedul Islam ◽  
Md Mahiuddin
Keyword(s):  
High Temperature ◽  
Molten Salt ◽  
Solar Collector ◽  
Volume Fraction ◽  
Heat Transfer Fluid ◽  
Total Efficiency ◽  
Total System ◽  
Direct Absorption ◽  
Wide Range ◽  
Direct Absorption Solar Collector

Nanofluids have great potential in a wide range of fields including solar thermal applications, where molten salt nanofluids have shown great potential as a heat transfer fluid (HTF) for use in high temperature solar applications. However, no study has investigated the use of molten salt nanofluids as the HTF in direct absorption solar collector systems (DAC). In this study, a two dimensional CFD model of a direct absorption high temperature molten salt nanofluid concentrating solar receiver has been developed to investigate the effects design and operating variables on receiver performance. It has been found that the Carnot efficiency increases with increasing receiver length, solar concentration, increasing height and decreasing inlet velocity. When coupled to a power generation cycle, it is predicted that total system efficiency can exceed 40% when solar concentrations are greater than 100×. To impart more emphasis on the temperature rise of the receiver, an adjusted Carnot efficiency has been used in conjunction with the upper temperature limit of the nanofluid. The adjusted total efficiency also resulted in a peak efficiency for solar concentration, which decreased with decreasing volume fraction, implying that each receiver configuration has an optimal solar concentration.

Assessment of a Molten Salt Heat Transfer Fluid in a Parabolic Trough Solar Field

2003 ◽  
Vol 125 (2) ◽  
pp. 170-176 ◽  
Author(s):  
D. Kearney ◽  
U. Herrmann ◽  
P. Nava ◽  
B. Kelly ◽  
R. Mahoney ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Molten Salt ◽  
Mojave Desert ◽  
Storage System ◽  
Eutectic Mixture ◽  
Heat Transfer Fluid ◽  
Diphenyl Oxide ◽  
Parabolic Trough ◽  
Electricity Cost ◽  
Solar Field

An evaluation was carried out to investigate the feasibility of utilizing a molten salt as the heat transfer fluid (HTF) and for thermal storage in a parabolic trough solar field to improve system performance and to reduce the levelized electricity cost. The operating SEGS (Solar Electric Generating Systems located in Mojave Desert, California) plants currently use a high temperature synthetic oil consisting of a eutectic mixture of biphenyl/diphenyl oxide. The scope of this investigation included examination of known critical issues, postulating solutions or possible approaches where potential problems exist, and the quantification of performance and electricity cost using preliminary cost inputs. The two leading candidates were the so-called solar salt (a binary salt consisting of 60% NaNO3 and 40% KNO3) and a salt sold commercially as HitecXL (a ternary salt consisting of 48% CaNO32, 7% NaNO3, and 45% KNO3). Assuming a two-tank storage system and a maximum operation temperature of 450°C, the evaluation showed that the levelized electricity cost can be reduced by 14.2% compared to a state-of-the-art parabolic trough plant such as the SEGS plants. If higher temperatures are possible, the improvement may be as high as 17.6%. Thermocline salt storage systems offer even greater benefits.

Sign in / Sign up

Export Citation Format

Share Document