Coupled electrostatic and material surface stresses yield anomalous particle interactions and deformation

2016 ◽  
Vol 119 (14) ◽  
pp. 145105 ◽  
Author(s):  
B. A. Kemp ◽  
I. Nikolayev ◽  
C. J. Sheppard
Keyword(s):  
Material Surface ◽  
Particle Interactions ◽  
Surface Stresses ◽  
Anomalous Particle

Suppression of γ’ Precipitation in a Laser-Melted Nickel-Base Alloy

1977 ◽  
Vol 35 ◽  
pp. 270-271
Author(s):  
J. M. Walsh ◽  
J. C. Whittles ◽  
B. H. Kear ◽  
E. M. Breinan
Keyword(s):  
Cooling Rate ◽  
Base Alloy ◽  
Material Surface ◽  
Intimate Contact ◽  
Absorbed Power ◽  
Perfect Contact ◽  
Nickel Base ◽  
Rapidly Solidified ◽  
Limiting Case ◽  
The Heat Transfer Coefficient

Conventionally cast γ’ precipitation hardened nickel-base superalloys possess well-defined dendritic structures and normally exhibit pronounced segregation. Splat quenched, or rapidly solidified alloys, on the other hand, show little or no evidence for phase decomposition and markedly reduced segregation. In what follows, it is shown that comparable results have been obtained in superalloys processed by the LASERGLAZE™ method.In laser glazing, a sharply focused laser beam is traversed across the material surface at a rate that induces surface localized melting, while avoiding significant surface vaporization. Under these conditions, computations of the average cooling rate can be made with confidence, since intimate contact between the melt and the self-substrate ensures that the heat transfer coefficient is reproducibly constant (h=∞ for perfect contact) in contrast to the variable h characteristic of splat quenching. Results of such computations for pure nickel are presented in Fig. 1, which shows that there is a maximum cooling rate for a given absorbed power density, corresponding to the limiting case in which melt depth approaches zero.

Microstructures of Laser Processed Fe-Cr Surface Alloys

1981 ◽  
Vol 39 ◽  
pp. 328-329
Author(s):  
P. A. Molian ◽  
K. H. Khan ◽  
W. E. Wood
Keyword(s):  
Cooling Rate ◽  
Pure Iron ◽  
Continuous Wave ◽  
Laser Surface ◽  
Material Surface ◽  
Constitution Diagram ◽  
Incident Power ◽  
Surface Alloying ◽  
Laser Surface Alloying ◽  
Spot Diameter

In recent years, the effects of chromium on the transformation characteristics of pure iron and the structures produced thereby have been extensively studied as a function of cooling rate. In this paper, we present TEM observations made on specimens of Fe-10% Cr and Fe-20% Cr alloys produced through laser surface alloying process with an estimated cooling rate of 8.8 x 104°C/sec. These two chromium levels were selected in order to study their phase transformation characteristics which are dissimilar in the two cases as predicted by the constitution diagram. Pure iron (C<0.01%, Si<0.01%, Mn<0.01%, S=0.003%, P=0.008%) was electrodeposited with chromium to the thicknesses of 40 and 70μm and then vacuum degassed at 400°F to remove the hydrogen formed during electroplating. Laser surface alloying of chromium into the iron substrate was then performed employing a continuous wave CO2 laser operated at an incident power of 1200 watts. The laser beam, defocussed to a spot diameter of 0.25mm, scanned the material surface at a rate of 30mm/sec, (70 ipm).

Sign in / Sign up

Export Citation Format

Share Document