A soft ferromagnetic multiwire-based inductance coil sensor for sensing applications

2014 ◽  
Vol 116 (23) ◽  
pp. 234504 ◽  
Author(s):  
J. Devkota ◽  
T. Luong ◽  
J. S. Liu ◽  
H. Shen ◽  
F. X. Qin ◽  
...  
Keyword(s):  
Inductance Coil ◽  
Sensing Applications ◽  
Soft Ferromagnetic

Computer simulation study about the dependence of amorphous silicon photonic waveguides efficiency on the material quality

2020 ◽  
Vol 90 (3) ◽  
pp. 30502
Author(s):  
Alessandro Fantoni ◽  
João Costa ◽  
Paulo Lourenço ◽  
Manuela Vieira
Keyword(s):  
Amorphous Silicon ◽  
High Throughput Screening ◽  
Simulation Analysis ◽  
Low Cost ◽  
Deposition Process ◽  
Large Area ◽  
Sidewall Roughness ◽  
Sensing Applications ◽  
Fabrication Defects ◽  
The Impact

Amorphous silicon PECVD photonic integrated devices are promising candidates for low cost sensing applications. This manuscript reports a simulation analysis about the impact on the overall efficiency caused by the lithography imperfections in the deposition process. The tolerance to the fabrication defects of a photonic sensor based on surface plasmonic resonance is analysed. The simulations are performed with FDTD and BPM algorithms. The device is a plasmonic interferometer composed by an a-Si:H waveguide covered by a thin gold layer. The sensing analysis is performed by equally splitting the input light into two arms, allowing the sensor to be calibrated by its reference arm. Two different 1 × 2 power splitter configurations are presented: a directional coupler and a multimode interference splitter. The waveguide sidewall roughness is considered as the major negative effect caused by deposition imperfections. The simulation results show that plasmonic effects can be excited in the interferometric waveguide structure, allowing a sensing device with enough sensitivity to support the functioning of a bio sensor for high throughput screening. In addition, the good tolerance to the waveguide wall roughness, points out the PECVD deposition technique as reliable method for the overall sensor system to be produced in a low-cost system. The large area deposition of photonics structures, allowed by the PECVD method, can be explored to design a multiplexed system for analysis of multiple biomarkers to further increase the tolerance to fabrication defects.

PHENOMENOLOGY OF BARKHAUSEN EFFECT IN SOFT FERROMAGNETIC MATERIALS

1988 ◽  
Vol 49 (C8) ◽  
pp. C8-1907-C8-1908 ◽  
Author(s):  
B. Alessandro ◽  
G. Bertotti ◽  
A. Montorsi
Keyword(s):  
Ferromagnetic Materials ◽  
Barkhausen Effect ◽  
Soft Ferromagnetic

The Role of Hydrophobicity in the Stability and pH-Switchability of (RXDX)4 and Coumarin-RXDX Conjugate β-Sheets

2020 ◽  
Author(s):  
Ryan Weber ◽  
Martin McCullagh
Keyword(s):  
Biological Imaging ◽  
Ph Sensing ◽  
Hydrophobic Residue ◽  
Ideal Candidate ◽  
Self Assembling ◽  
Sensing Applications ◽  
Β Sheets ◽  
The Stability ◽  
Dynamics Simulations

<p>pH-switchable, self-assembling materials are of interest in biological imaging and sensing applications. Here we propose that combining the pH-switchability of RXDX (X=Ala, Val, Leu, Ile, Phe) peptides and the optical properties of coumarin creates an ideal candidate for these materials. This suggestion is tested with a thorough set of all-atom molecular dynamics simulations. We first investigate the dependence of pH-switchabiliy on the identity of the hydrophobic residue, X, in the bare (RXDX)<sub>4</sub> systems. Increasing the hydrophobicity stabilizes the fiber which, in turn, reduces the pH-switchabilty of the system. This behavior is found to be somewhat transferable to systems in which a single hydrophobic residue is replaced with a coumarin containing amino acid. In this case, conjugates with X=Ala are found to be unstable and both pHs while conjugates with X=Val, Leu, Ile and Phe are found to form stable β-sheets at least at neutral pH. The (RFDF)<sub>4</sub>-coumarin conjugate is found to have the largest relative entropy value of 0.884 +/- 0.001 between neutral and acidic coumarin ordering distributions. Thus, we posit that coumarin-(RFDF)<sub>4</sub> containing peptide sequences are ideal candidates for pH-sensing bioelectronic materials.</p>

A Fully Differential Variable Gain Amplifier for Portable Impedance Sensing Applications

2019 ◽  
Vol 7 ◽  
Author(s):  
Jorge Pérez Bailón ◽  
Jaime Ramírez-Angulo ◽  
Belén Calvo ◽  
Nicolás Medrano
Keyword(s):  
Power Consumption ◽  
Active Area ◽  
Variable Gain Amplifier ◽  
Cmos Process ◽  
Current Steering ◽  
Impedance Sensing ◽  
Variable Gain ◽  
Fully Differential ◽  
Sensing Applications ◽  
Constant Bandwidth

This paper presents a Variable Gain Amplifier (VGA) designed in a 0.18 μm CMOS process to operate in an impedance sensing interface. Based on a transconductance-transimpedance (TC-TI) approach with intermediate analog-controlled current steering, it exhibits a gain ranging from 5 dB to 38 dB with a constant bandwidth around 318 kHz, a power consumption of 15.5 μW at a 1.8 V supply and an active area of 0.021 mm2.

Sign in / Sign up

Export Citation Format

Share Document