scholarly journals Prediction and analysis of infra and low-frequency noise of upwind horizontal axis wind turbine using statistical wind speed model

AIP Advances ◽  
2014 ◽  
Vol 4 (12) ◽  
pp. 127117 ◽  
Author(s):  
Gwang-Se Lee ◽  
Cheolung Cheong
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Low Frequency ◽  
Horizontal Axis ◽  
Frequency Noise ◽  
Low Frequency Noise ◽  
Horizontal Axis Wind Turbine

scholarly journals Investigation of an Innovative Rotor Modification for a Small-Scale Horizontal Axis Wind Turbine

Energies ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2649 ◽  
Author(s):  
Artur Bugała ◽  
Olga Roszyk
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Cfd Simulation ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Horizontal Axis ◽  
Power Coefficient ◽  
Small Scale ◽  
Horizontal Axis Wind Turbine ◽  
Airflow Distribution

This paper presents the results of the computational fluid dynamics (CFD) simulation of the airflow for a 300 W horizontal axis wind turbine, using additional structural elements which modify the original shape of the rotor in the form of multi-shaped bowls which change the airflow distribution. A three-dimensional CAD model of the tested wind turbine was presented, with three variants subjected to simulation: a basic wind turbine without the element that modifies the airflow distribution, a turbine with a plano-convex bowl, and a turbine with a centrally convex bowl, with the hyperbolic disappearance of convexity as the radius of the rotor increases. The momentary value of wind speed, recorded at measuring points located in the plane of wind turbine blades, demonstrated an increase when compared to the base model by 35% for the wind turbine with the plano-convex bowl, for the wind speed of 5 m/s, and 31.3% and 49% for the higher approaching wind speed, for the plano-convex bowl and centrally convex bowl, respectively. The centrally convex bowl seems to be more appropriate for higher approaching wind speeds. An increase in wind turbine efficiency, described by the power coefficient, for solutions with aerodynamic bowls was observed.

Optimal Design of Horizontal Axis Wind Turbine Blades

2008 ◽  
Author(s):  
Ohad Gur ◽  
Aviv Rosen
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Design Method ◽  
Turbine Blades ◽  
Horizontal Axis ◽  
Optimization Strategy ◽  
Wind Turbine Blades ◽  
Horizontal Axis Wind Turbine ◽  
Wind Speeds ◽  
Design Variables

The optimal aerodynamic design of Horizontal Axis Wind Turbine (HAWT) is investigated. The Blade-element/Momentum model is used for the aerodynamic analysis. In the first part of the paper a simple design method is derived, where the turbine blade is optimized for operation at a specific wind speed. Results of this simple optimization are presented and discussed. Besides being optimized for operation at a specific wind speed, without considering operation at other wind speeds, the simple model is also limited in the choice of design goals (cost functions), design variables and constraints. In the second part of the paper a comprehensive design method that is based on a mixed numerical optimization strategy, is presented. This method can handle almost any combination of: design goal, design variables, and constraints. Results of this method are presented, compared with the results of the simple optimization, and discussed.

scholarly journals Experimental investigations of winglet effects on blade geometry of small horizontal axis wind turbine rotors

2021 ◽  
Author(s):  
Manoj Kumar Chaudhary ◽  
◽  
S. Prakash ◽  
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Lift Coefficient ◽  
Research Work ◽  
Operating Conditions ◽  
Horizontal Axis ◽  
Power Coefficient ◽  
Experimental Investigations ◽  
Horizontal Axis Wind Turbine ◽  
Blade Geometry

In this research work, the investigation and optimization of small horizontal axis wind turbine blade at low wind speed is pursued. The experimental blades were developed using the 3D printing additive manufacturing technique. The airfoils E210, NACA2412, S1223, SG6043, E216, NACA4415, SD7080, SD7033, S1210 and MAF were tested at the wind speed of 2-6 m/s. The airfoils and optimum blade geometry were investigated with the aid of the Xfoil software at Reynolds number of 100,000. The initial investigation range included tip speed ratios from 3 to 10, solidity from 0.0431 – 0.1181 and angle of attacks from 2o to 20o. Later on these parameters were varied in MATLAB and Xfoil software for optimization and investigation of the power coefficient, lift coefficient, drag coefficient and lift to drag ratio. The cut-in wind speed of the rotors was 2 and 2.5 m/s with the winglet-equipped blades and without winglets. It was found that the E210, SG6043, E216 NACA4415 and MAF airfoil displayed better performance than the NACA 2412, S1223, SD7080, S1210 & SD7003 for the geometry optimized for the operating conditions and manufacturing method described.

scholarly journals Airfoil optimization for small horizontal axis wind turbine

2021 ◽  
Vol 19 ◽  
pp. 505-510
Author(s):  
Cristhian Leonardo Pabón Rojas ◽  
◽  
Carlos Andrés Trujillo Suarez ◽  
Juan Carlos Serrano Rico ◽  
Elkin Gregorio Flórez Serrano ◽  
...  
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Pitch Angle ◽  
Horizontal Axis ◽  
Middle Zone ◽  
Horizontal Axis Wind Turbine ◽  
Airfoil Optimization ◽  
Low Wind Speed ◽  
Gradient Based ◽  
Blade Element

In order to take advantage of the low wind speed found in the Colombian territory, a gradient-based optimization process (GBA) of 2 airfoils is carried out, using the Xfoil software to evaluate the interactions. The shapes chosen will be destined for the root and for the middle zone of a blade for a small horizontal axis wind turbine (sHAWT). The blade will be created from the calculation of the chord and pitch angle with the blade element momentum methodology (BEM) and the SHAWT will be tested by CFD software to check its performance. As a preliminary result, a root-bound airfoil has been obtained with a higher performance than the airfoil used as a bases.

Sign in / Sign up

Export Citation Format

Share Document