Short-circuit current density imaging of crystalline silicon solar cells via lock-in thermography: Robustness and simplifications

2014 ◽  
Vol 116 (18) ◽  
pp. 184501 ◽  
Author(s):  
Fabian Fertig ◽  
Johannes Greulich ◽  
Stefan Rein
Keyword(s):  
Solar Cells ◽  
Current Density ◽  
Crystalline Silicon ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Silicon Solar Cells ◽  
Crystalline Silicon Solar Cells ◽  
Current Density Imaging ◽  
Lock In

scholarly journals Effect of the Phosphorus Gettering on Si Heterojunction Solar Cells

2012 ◽  
Vol 2012 ◽  
pp. 1-7 ◽  
Author(s):  
Hyomin Park ◽  
Sung Ju Tark ◽  
Chan Seok Kim ◽  
Sungeun Park ◽  
Young Do Kim ◽  
...  
Keyword(s):  
Solar Cells ◽  
Current Density ◽  
Crystalline Silicon ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Solar Simulator ◽  
Heterojunction Solar Cells ◽  
Crystalline Silicon Solar Cells

To improve the efficiency of crystalline silicon solar cells, should be collected the excess carrier as much as possible. Therefore, minimizing the recombination both at the bulk and surface regions is important. Impurities make recombination sites and they are the major reason for recombination. Phosphorus (P) gettering was introduced to reduce metal impurities in the bulk region of Si wafers and then to improve the efficiency of Si heterojunction solar cells fabricated on the wafers. Resistivity of wafers was measured by a four-point probe method. Fill factor of solar cells was measured by a solar simulator. Saturation current and ideality factor were calculated from a dark current density-voltage graph. External quantum efficiency was analyzed to assess the effect of P gettering on the performance of solar cells. Minority bulk lifetime measured by microwave photoconductance decay increases from 368.3 to 660.8 μs. Open-circuit voltage and short-circuit current density increase from 577 to 598 mV and 27.8 to 29.8 mA/cm2, respectively. The efficiency of solar cells increases from 11.9 to 13.4%. P gettering will be feasible to improve the efficiency of Si heterojunction solar cells fabricated on P-doped Si wafers.

scholarly journals Short-circuit Current Density Imaging Methods for Silicon Solar Cells

2015 ◽  
Vol 77 ◽  
pp. 43-56 ◽  
Author(s):  
Fabian Fertig ◽  
Milan Padilla ◽  
Otwin Breitenstein ◽  
Hannes Höffler ◽  
Ino Geisemeyer ◽  
...  
Keyword(s):  
Solar Cells ◽  
Current Density ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Silicon Solar Cells ◽  
Imaging Methods ◽  
Current Density Imaging

scholarly journals Novel Photonic Crystal Based Polycrystalline CdTe/Silicon Solar Cells

2020 ◽  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Photonic Crystal ◽  
Conversion Efficiency ◽  
Current Density ◽  
Cell Structure ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Silicon Solar Cells

In this paper, a novel photonic crystal (PhC) polycrystalline CdTe/Silicon solar cells are theoretically explained that increase their short circuit current density and conversion efficiency. The proposed structure consist of a polycrystalline CdTe/Silicon solar cell that a photonic crystal is formed in the upper cell. The optical confinement is achieved by means of photonic crystal that can adjust the propagation and distribution of photons in solar cells. For validation of modeling, the electrical properties of the experimentally-fabricated based CdS/CdTe solar cell is modeled and compared that there is good agreement between the modeling results and experimental results from the litterature. The results of this study showed that the solar cell efficiency is increased by about 25% compared to the reference cell by using photonic crystal. The open circuit voltage, short circuit current density, fill factor and conversion efficiency of proposed solar cell structure are 1.01 V, 40.7 mA/cm2, 0.95 and 27% under global AM 1.5 conditions, respectively. Furthermore, the influence of carrier lifetime variation in the absorber layer of proposed solar cell on the electrical characteristics was theoretically considered and investigated.

Influence of ITO layer application on electrical parameters of silicon solar cells with screen printed front electrode

2016 ◽  
Vol 33 (3) ◽  
pp. 172-175 ◽  
Author(s):  
Kazimierz Drabczyk ◽  
Jaroslaw Domaradzki ◽  
Grazyna Kulesza-Matlak ◽  
Marek Lipinski ◽  
Danuta Kaczmarek
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Crystalline Silicon ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Electrical Performance ◽  
Silicon Solar Cells ◽  
Content Type ◽  
Crystalline Silicon Solar Cells ◽  
Screen Printed

Purpose The purpose of this paper was investigation and comparison of electrical and optical properties of crystalline silicon solar cells with ITO or TiO2 coating. The ITO, similar to TiO2, is very well transparent in the visible part of optical radiation; however, its low resistivity (lower that 10-3 Ohm/cm) makes it possible to use simultaneously as a transparent electrode for collection of photo-generated electrical charge carriers. This might also invoke increasing the distance between screen-printed metal fingers at the front of the solar cell that would increase of the cell’s active area. Performed optical investigation showed that applied ITO thin film fulfill standard requirements according to antireflection properties when it was deposited on the surface of silicon solar cell. Design/methodology/approach Two sets of samples were prepared for comparison. In the first one, the ITO thin film was deposited directly on the crystalline silicon substrate with highly doped emitter region. In the second case, the TCO film was deposited on the same type of silicon substrate but with additional ultrathin SiO2 passivation. The fingers lines of 80 μm width were then screen-printed on the ITO layer with two different spaces between fingers for each set. The influence of application of the ITO electrode and the type of metal electrodes patterns on the electrical performance of the prepared solar cells was investigated through optical and electrical measurements. Findings The electrical parameters such as short-circuit current (Jsc), open circuit voltage (Voc), fill factor (FF) and conversion efficiency were determined on a basis of I-V characteristics. Short-circuit current density (Jsc) was equal to 32 mA/cm2 for a solar cell with a typical antireflection layer and 31.5 mA/cm2 for the cell with ITO layer, respectively. Additionally, electroluminescence of prepared cells was measured and analysed. Originality/value The influence of the properties of ITO electrode on the electrical performance of crystalline silicon solar cells was investigated through complex optical, electrical and electroluminescence measurements.

Sign in / Sign up

Export Citation Format

Share Document