Guided wave mode pairs for transmissibility in adhesively bonded metal plates

2013 ◽  
Author(s):  
P. Puthillath ◽  
B. Ren ◽  
C. J. Lissenden ◽  
J. L. Rose
Keyword(s):  
Wave Mode ◽  
Guided Wave ◽  
Adhesively Bonded ◽  
Metal Plates

scholarly journals Phase-delayed laser diode array allows ultrasonic guided wave mode selection and tuning

2013 ◽  
Vol 113 (14) ◽  
pp. 144904 ◽  
Author(s):  
Pasi Karppinen ◽  
Ari Salmi ◽  
Petro Moilanen ◽  
Timo Karppinen ◽  
Zuomin Zhao ◽  
...  
Keyword(s):  
Laser Diode ◽  
Mode Selection ◽  
Wave Mode ◽  
Guided Wave ◽  
Diode Array ◽  
Laser Diode Array ◽  
Ultrasonic Guided Wave

scholarly journals Numerical Simulation on Micro-damage Detection In CFRP Composites Based on Nonlinear Ultrasonic Guided Waves

2021 ◽  
Keyword(s):  
Damage Detection ◽  
Composite Structures ◽  
Guided Waves ◽  
Second Harmonic ◽  
Wave Mode ◽  
Guided Wave ◽  
Reinforced Plastics ◽  
Matrix Cracks ◽  
Nonlinear Ultrasonic ◽  
Contact Acoustic Nonlinearity

Abstract. Micro-damages such as pores, closed delamination/debonding and fiber/matrix cracks in carbon fiber reinforced plastics (CFRP) are vital factors towards the performance of composite structures, which could collapse if defects are not detected in advance. Nonlinear ultrasonic technologies, especially ones involving guided waves, have drawn increasing attention for their better sensitivity to early damages than linear acoustic ones. The combination of nonlinear acoustics and guided waves technique can promisingly provide considerable accuracy and efficiency for damage assessment and materials characterization. Herein, numerical simulations in terms of finite element method are conducted to investigate the feasibility of micro-damage detection in multi-layered CFRP plates using the second harmonic generation (SHG) of asymmetric Lamb guided wave mode. Contact acoustic nonlinearity (CAN) is introduced into the constitutive model of micro-damages in composites, which leads to the distinct SHG compared with material nonlinearity. The results suggest that the generated second order harmonics due to CAN could be received and adopted for early damage evaluation without matching the phase of the primary waves.

Detection of Defects in Titanium Using Shear Horizontal Guided Waves

2021 ◽  
Author(s):  
Christian Peyton ◽  
Rachel S. Edwards ◽  
Steve Dixon ◽  
Ben Dutton ◽  
Wilson Vesga
Keyword(s):  
Guided Waves ◽  
Wave Mode ◽  
Guided Wave ◽  
Inspection System ◽  
Wave Direction ◽  
Finite Element Software ◽  
Small Defect ◽  
Back Face ◽  
The Relationship ◽  
Shear Horizontal

Abstract This paper investigates the interaction behaviour between the fundamental shear horizontal guided wave mode and small defects, in order to understand and develop an improved inspection system for titanium samples. In this work, an extensive range of defect sizes have been simulated using finite element software. The SH0 reflection from a defect has been shown previously to depend on its length as the total reflection consists of reflections from both the front and back face. However, for small defect widths, this work has found that the width also affects this interference, changing the length at which the reflection is largest. In addition, the paper looks at how the size of the defect affects the mode converted S0 reflection and SH0 diffraction. The relationship between the SH0 diffraction and defect size is shown to be more complex compared to the reflections. The mode converted S0 reflection occurs at an angle to the incident wave direction; therefore, the most suitable angle for the detection has been found. Simultaneous measurement of multiple waves would bring benefits to inspection.

scholarly journals Detection of debonding in adhesive joints using Lamb wave propagation

2019 ◽  
Vol 262 ◽  
pp. 10012
Author(s):  
Magdalena Rucka ◽  
Erwin Wojtczak ◽  
Jacek Lachowicz
Keyword(s):  
Wave Propagation ◽  
Lamb Waves ◽  
Visual Assessment ◽  
Guided Wave ◽  
Steel Plates ◽  
Experimental Investigations ◽  
Mechanical Degradation ◽  
Adhesively Bonded ◽  
Destructive Testing ◽  
Out Of Plane

Adhesively bonded joints are widely used in many branches of industry. Mechanical degradation of this type of connections does not have significant symptoms that can be noticed during visual assessment, so non-destructive testing becomes a very important issue. The paper deals with experimental investigations of adhesively bonded steel plates with different defects. Five samples (an intact one and four with damages in the form of partial debonding) were prepared. The inspection was conducted with the use of guided wave propagation method. Lamb waves were excited at one point of the sample, whereas the out-of-plane velocity signals were recorded in a number of points spread over the area of overlap. The processing of signals consisted of calculations of weighted root mean square (WRMS). The results of the analysis showed that the WRMS maps allow for identification and determination of size and shape of debonding areas.

scholarly journals Development of Ultrasonic Guided Wave Transducer for Monitoring of High Temperature Pipelines

Sensors ◽  
2019 ◽  
Vol 19 (24) ◽  
pp. 5443 ◽  
Author(s):  
Anurag Dhutti ◽  
Saiful Asmin Tumin ◽  
Wamadeva Balachandran ◽  
Jamil Kanfoud ◽  
Tat-Hean Gan
Keyword(s):  
High Temperature ◽  
Guided Waves ◽  
Elevated Temperatures ◽  
Element Model ◽  
Wave Mode ◽  
Guided Wave ◽  
Electromechanical Impedance ◽  
Active Sensor ◽  
Ultrasonic Guided Wave ◽  
Modes Of Vibration

High-temperature (HT) ultrasonic transducers are of increasing interest for structural health monitoring (SHM) of structures operating in harsh environments. This article focuses on the development of an HT piezoelectric wafer active sensor (HT-PWAS) for SHM of HT pipelines using ultrasonic guided waves. The PWAS was fabricated using Y-cut gallium phosphate (GaPO4) to produce a torsional guided wave mode on pipes operating at temperatures up to 600 °C. A number of confidence-building tests on the PWAS were carried out. HT electromechanical impedance (EMI) spectroscopy was performed to characterise piezoelectric properties at elevated temperatures and over long periods of time (>1000 h). Laser Doppler vibrometry (LDV) was used to verify the modes of vibration. A finite element model of GaPO4 PWAS was developed to model the electromechanical behaviour of the PWAS and the effect of increasing temperatures, and it was validated using EMI and LDV experimental data. This study demonstrates the application of GaPO4 for guided-wave SHM of pipelines and presents a model that can be used to evaluate different transducer designs for HT applications.

Sign in / Sign up

Export Citation Format

Share Document