Homogeneous nucleation rates for n‐alcohol vapors measured in a two‐piston expansion chamber

1986 ◽  
Vol 84 (4) ◽  
pp. 2325-2335 ◽  
Author(s):  
R. Strey ◽  
P. E. Wagner ◽  
T. Schmeling
Keyword(s):  
Homogeneous Nucleation ◽  
Expansion Chamber

Exsolution and inversion in pigeonite from the Whin Sill, Northern England

1978 ◽  
Vol 36 (1) ◽  
pp. 474-475
Author(s):  
P.P.K. Smith
Keyword(s):  
High Temperature ◽  
Low Temperature ◽  
Homogeneous Nucleation ◽  
Silicate Mineral ◽  
Antiphase Boundaries ◽  
Two Phase ◽  
Primitive Form ◽  
The Core ◽  
Nucleation Mechanisms ◽  
And Inversion

Grains of pigeonite, a calcium-poor silicate mineral of the pyroxene group, from the Whin Sill dolerite have been ion-thinned and examined by TEM. The pigeonite is strongly zoned chemically from the composition Wo8En64FS28 in the core to Wo13En34FS53 at the rim. Two phase transformations have occurred during the cooling of this pigeonite:- exsolution of augite, a more calcic pyroxene, and inversion of the pigeonite from the high- temperature C face-centred form to the low-temperature primitive form, with the formation of antiphase boundaries (APB's). Different sequences of these exsolution and inversion reactions, together with different nucleation mechanisms of the augite, have created three distinct microstructures depending on the position in the grain.In the core of the grains small platelets of augite about 0.02μm thick have farmed parallel to the (001) plane (Fig. 1). These are thought to have exsolved by homogeneous nucleation. Subsequently the inversion of the pigeonite has led to the creation of APB's.

Lattice imaging of precipitates in Al-Zn-Mg alloy

1986 ◽  
Vol 44 ◽  
pp. 412-413
Author(s):  
C. K. Wu
Keyword(s):  
Grain Boundaries ◽  
Homogeneous Nucleation ◽  
Alloy System ◽  
Mg Alloy ◽  
List Type ◽  
Lattice Structures ◽  
Type Number ◽  
Orientation Relationships ◽  
Lattice Imaging ◽  
The Matrix

The precipitation phenomenon in Al-Zn-Mg alloy is quite interesting and complicated and can be described in the following categories:(i) heterogeneous nucleation at grain boundaries;(ii) precipitate-free-zones (PFZ) adjacent to the grain boundaries;(iii) homogeneous nucleation of snherical G.P. zones, n' and n phases inside the grains. The spherical G.P. zones are coherent with the matrix, whereas the n' and n phases are incoherent. It is noticed that n' and n phases exhibit plate-like morpholoay with several orientation relationship with the matrix. The high resolution lattice imaging techninue of TEM is then applied to study precipitates in this alloy system. It reveals the characteristics of lattice structures of each phase and the orientation relationships with the matrix.

Amorphous silica coating on α-alumina particles

1995 ◽  
Vol 53 ◽  
pp. 210-211
Author(s):  
J. W. Mellowes ◽  
C. M. Chun ◽  
I. A. Aksay
Keyword(s):  
Amorphous Silica ◽  
Heterogeneous Nucleation ◽  
Homogeneous Nucleation ◽  
Silica Coating ◽  
Full Density ◽  
Optimal Conditions ◽  
Fine Grained ◽  
Alumina Particles ◽  
Complete Mullitization ◽  
Powder Compacts

Mullite (3Al2O32SiO2) can be fabricated by transient viscous sintering using composite particles which consist of inner cores of a-alumina and outer coatings of amorphous silica. Powder compacts prepared with these particles are sintered to almost full density at relatively low temperatures (~1300°C) and converted to dense, fine-grained mullite at higher temperatures (>1500°C) by reaction between the alumina core and the silica coating. In order to achieve complete mullitization, optimal conditions for coating alumina particles with amorphous silica must be achieved. Formation of amorphous silica can occur in solution (homogeneous nucleation) or on the surface of alumina (heterogeneous nucleation) depending on the degree of supersaturation of the solvent in which the particles are immersed. Successful coating of silica on alumina occurs when heterogeneous nucleation is promoted and homogeneous nucleation is suppressed. Therefore, one key to successful coating is an understanding of the factors such as pH and concentration that control silica nucleation in aqueous solutions. In the current work, we use TEM to determine the optimal conditions of this processing.

Sign in / Sign up

Export Citation Format

Share Document