Effect of surfactant molecular weight on particle morphology of SmCo5 prepared by high energy ball milling

2012 ◽  
Vol 111 (7) ◽  
pp. 07A724 ◽  
Author(s):  
C. A. Crouse ◽  
E. Michel ◽  
Y. Shen ◽  
S. J. Knutson ◽  
B. K. Hardenstein ◽  
...  
Keyword(s):  
Molecular Weight ◽  
Ball Milling ◽  
Particle Morphology ◽  
High Energy ◽  
High Energy Ball Milling ◽  
Energy Ball

Effect of High-Energy Ball Milling on Microstructure and Microwave Absorbing Properties of NdFe Material

2011 ◽  
Vol 311-313 ◽  
pp. 1281-1285 ◽  
Author(s):  
Pei Hao Lin ◽  
Lei Wang ◽  
Shun Kang Pan ◽  
Hua Mei Wan
Keyword(s):  
Ball Milling ◽  
Particle Morphology ◽  
High Energy ◽  
High Energy Ball Milling ◽  
X Ray ◽  
Microwave Absorbing Properties ◽  
Absorbing Materials ◽  
Milling Method ◽  
Energy Ball ◽  
Microwave Absorbing

The NdFe magnetic absorbing materials were prepared by rapid solidification and high-energy ball milling method. The effect of high-energy ball milling on particle morphology, organizational structure and microwave absorbing properties of NdFe magnetic absorbing materials were analyzed with the aid of X-ray diffractometer, scanning electron microscope and vector network analysis. The results show that the Nd2Fe17 and α-Fe phase are refined, the particles become smaller and thinner; the span-ratio of the particles increases along with time during the process of high-energy ball milling; and meanwhile, the frequency of absorbing peak reduces. The absorbing bandwidth broadens as the increase of the time of ball milling, except that of 48h.The minimum reflectance of the powder decreases from -22dB to - 44dB under the circumstances that the time of high energy ball milling reaches 48h and the thickness of the microwave absorbing coating is 1.5mm. But it rebounds to about - 6dB when the time of ball milling reaches 72h.

Mechanical Alloying of Pet and Pet/Vectra Blends

1996 ◽  
Vol 461 ◽  
Author(s):  
C. M. Balik ◽  
C Bai ◽  
C.C Koch ◽  
R.J Spontak ◽  
C. K. Saw
Keyword(s):  
Molecular Weight ◽  
Mechanical Alloying ◽  
Ball Milling ◽  
Liquid Nitrogen ◽  
Room Temperature ◽  
Potential Method ◽  
High Energy ◽  
High Energy Ball Milling ◽  
Weight Density ◽  
Energy Ball

ABSTRACTMechanical alloying represents a potential method for producing finely dispersed alloys of normally incompatible polymers. In this paper, PET and blends of PET with a Vectra thermotropic copolyester have been processed via high energy ball milling at room temperature (ambimilled) and at liquid nitrogen temperatures (cryomilled). Milled powders and compacted disks have been characterized using molecular weight, density and hardness measurements, aswell as DSC, WAXS, TEM and FTIR.

scholarly journals Impact Evaluation of High Energy Ball Milling Homogenization Process in the Phase Distribution of Hydroxyapatite-Barium Titanate Plasma Spray Biocoating

Coatings ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 728
Author(s):  
Roberto Gómez Batres ◽  
Zelma S. Guzmán Escobedo ◽  
Karime Carrera Gutiérrez ◽  
Irene Leal Berumen ◽  
Abel Hurtado Macias ◽  
...  
Keyword(s):  
Barium Titanate ◽  
Ball Milling ◽  
Plasma Spray ◽  
Bonding Strength ◽  
Phase Distribution ◽  
High Energy ◽  
High Energy Ball Milling ◽  
X Ray ◽  
Nanomechanical Properties ◽  
Energy Ball

Air plasma spray technique (APS) is widely used in the biomedical industry for the development of HA-based biocoatings. The present study focuses on the influence of powder homogenization treatment by high-energy ball milling (HEBM) in developing a novel hydroxyapatite-barium titanate (HA/BT) composite coating deposited by APS; in order to compare the impact of the milling process, powders were homogenized by mechanical stirring homogenization (MSH) too. For the two-homogenization process, three weight percent ratios were studied; 10%, 30%, and 50% w/w of BT in the HA matrix. The phase and crystallite size were analyzed by X-ray diffraction patterns (XRD); the BT-phase distribution in the coating was analyzed by backscattered electron image (BSE) with a scanning electron microscope (SEM); the energy-dispersive X-ray spectroscopy (EDS) analysis was used to determinate the Ca/P molar ratio of the coatings, the degree of adhesion (bonding strength) of coatings was determinate by pull-out test according to ASTM C633, and finally the nanomechanical properties was determinate by nanoindentation. In the results, the HEBM powder processing shows better efficiency in phase distribution, being the 30% (w/w) of BT in HA matrix that promotes the best bonding strength performance and failure type conduct (cohesive-type), on the other hand HEBM powder treatment promotes a slightly greater crystal phase stability and crystal shrank conduct against MSH; the HEBM promotes a better behavior in the nanomechanical properties of (i) adhesive strength, (ii) cohesive/adhesive failure-type, (iii) stiffness, (iv) elastic modulus, and (v) hardness properties.

scholarly journals Effect of the route and sintering time in the microstructure of pure aluminum prepared by high energy ball milling

2021 ◽  
Vol 27 (S1) ◽  
pp. 3294-3296
Author(s):  
José Mendoza ◽  
C. Carreño-Gallardo ◽  
I. Estrada-Guel ◽  
C.G. Garay-Reyes ◽  
M.A. Ruiz-Esparza-Rodriguez ◽  
...  
Keyword(s):  
Ball Milling ◽  
Pure Aluminum ◽  
High Energy ◽  
High Energy Ball Milling ◽  
Sintering Time ◽  
Energy Ball

Atomic structure, magnetism, and transport properties of damaged La0.67Ca0.33MnO3−δ processed via high-energy ball milling

1999 ◽  
Vol 86 (3) ◽  
pp. 1607-1610 ◽  
Author(s):  
Michael B. Liou ◽  
Shaheen Islam ◽  
D. J. Fatemi ◽  
V. M. Browning ◽  
D. J. Gillespie ◽  
...  
Keyword(s):  
Transport Properties ◽  
Ball Milling ◽  
Atomic Structure ◽  
High Energy ◽  
High Energy Ball Milling ◽  
Energy Ball
Sign in / Sign up

Export Citation Format

Share Document