Anisotropic dissipative effects on the buoyancy instability with background heat flux

2011 ◽  
Vol 18 (3) ◽  
pp. 032106
Author(s):  
Haijun Ren ◽  
Jintao Cao ◽  
Zhengwei Wu ◽  
Paul K. Chu
Keyword(s):  
Heat Flux ◽  
Dissipative Effects ◽  
Buoyancy Instability

Siphon Flows in Stratified Coronal Loops

1994 ◽  
Vol 144 ◽  
pp. 185-187
Author(s):  
S. Orlando ◽  
G. Peres ◽  
S. Serio
Keyword(s):  
Heat Flux ◽  
Scaling Laws ◽  
Flow Model ◽  
Supersonic Flows ◽  
Coronal Loops ◽  
Characteristic Parameters

AbstractWe have developed a detailed siphon flow model for coronal loops. We find scaling laws relating the characteristic parameters of the loop, explore systematically the space of solutions and show that supersonic flows are impossible for realistic values of heat flux at the base of the upflowing leg.

Rate of Sublimation of Ice by Radiative Heating in Freeze-Etching

1980 ◽  
Vol 38 ◽  
pp. 618-619
Author(s):  
Yeshayahu Talmon
Keyword(s):  
Heat Flux ◽  
Freeze Fracture ◽  
Constant Heat Flux ◽  
Radiative Heating ◽  
Constant Heat ◽  
Entire Sample ◽  
Simplified Method ◽  
Freeze Etching ◽  
Sublimation Rates ◽  
Fractured Surface

To bring out details in the fractured surface of a frozen sample in the freeze fracture/freeze-etch technique,the sample or part of it is warmed to enhance water sublimation.One way to do this is to raise the temperature of the entire sample to about -100°C to -90°C. In this case sublimation rates can be calculated by using plots such as Fig.1 (Talmon and Thomas),or by simplified formulae such as that given by Menold and Liittge. To achieve higher rates of sublimation without heating the entire sample a radiative heater can be used (Echlin et al.). In the present paper a simplified method for the calculation of the rates of sublimation under a constant heat flux F [W/m2] at the surface of the sample from a heater placed directly above the sample is described.

DISSIPATIVE EFFECTS IN PROJECTILE FRAGMENTATION AND PARTICLES EVAPORATION

1987 ◽  
Vol 48 (C2) ◽  
pp. C2-175-C2-178
Author(s):  
A. BONASERA ◽  
M. DI TORO ◽  
C. GREGOIRE
Keyword(s):  
Projectile Fragmentation ◽  
Dissipative Effects

Numerical analysis of local heat flux and thin-slab solidification in a CSP funnel-type mold with electromagnetic braking

2020 ◽  
Vol 117 (6) ◽  
pp. 602
Author(s):  
Heping Liu ◽  
Jianjun Zhang ◽  
Hongbiao Tao ◽  
Hui Zhang
Keyword(s):  
Heat Flux ◽  
Casting Speed ◽  
Shell Growth ◽  
Local Heat ◽  
Operating Conditions ◽  
Thin Slab ◽  
Wide Face ◽  
Slab Width ◽  
Steel Grades ◽  
Local Heat Flux

In this article, based on the actual monitored temperature data from mold copper plate with a dense thermocouple layout and the measured magnetic flux density values in a CSP thin-slab mold, the local heat flux and thin-slab solidification features in the funnel-type mold with electromagnetic braking are analyzed. The differences of local heat flux, fluid flow and solidified shell growth features between two steel grades of Q235B with carbon content of 0.19%C and DC01 of 0.03%C under varying operation conditions are discussed. The results show the maximum transverse local heat flux is near the meniscus region of over 0.3 m away from the center of the wide face, which corresponds to the upper flow circulation and the large turbulent kinetic energy in a CSP funnel-type mold. The increased slab width and low casting speed can reduce the fluctuation of the transverse local heat flux near the meniscus. There is a decreased transverse local heat flux in the center of the wide face after the solidified shell is pulled through the transition zone from the funnel-curve to the parallel-cure zone. In order to achieve similar metallurgical effects, the braking strength should increase with the increase of casting speed and slab width. Using the strong EMBr field in a lower casting speed might reverse the desired effects. There exist some differences of solidified shell thinning features for different steel grades in the range of the funnel opening region under the measured operating conditions, which may affect the optimization of the casting process in a CSP caster.

Analysis of significant measures for thermal conductivity

2020 ◽  
pp. 35-42
Author(s):  
Yuri P. Zarichnyak ◽  
Vyacheslav P. Khodunkov
Keyword(s):  
Thermal Conductivity ◽  
Heat Flux ◽  
Surface Heat Flux ◽  
Heat Flux Density ◽  
Measurement Method ◽  
Conductivity Measurement ◽  
Surface Heat ◽  
Measuring Instrument ◽  
New Class ◽  
Achievable Accuracy

The analysis of a new class of measuring instrument for heat quantities based on the use of multi-valued measures of heat conductivity of solids. For example, measuring thermal conductivity of solids shown the fallacy of the proposed approach and the illegality of the use of the principle of ambiguity to intensive thermal quantities. As a proof of the error of the approach, the relations for the thermal conductivities of the component elements of a heat pump that implements a multi-valued measure of thermal conductivity are given, and the limiting cases are considered. In two ways, it is established that the thermal conductivity of the specified measure does not depend on the value of the supplied heat flow. It is shown that the declared accuracy of the thermal conductivity measurement method does not correspond to the actual achievable accuracy values and the standard for the unit of surface heat flux density GET 172-2016. The estimation of the currently achievable accuracy of measuring the thermal conductivity of solids is given. The directions of further research and possible solutions to the problem are given.

Sign in / Sign up

Export Citation Format

Share Document