Study of The Porosity Occurrence in Composite Materials by Means of Ultrasonic and In-Plane Shear Testing

2010 ◽  
Author(s):  
Cinzia Toscano ◽  
Carlo Vitiello ◽  
Pietro Caramuta ◽  
A. D’Amore ◽  
Domenico Acierno ◽  
...  
Keyword(s):  
Composite Materials ◽  
Shear Testing ◽  
Plane Shear

Determination of In-plane Shear Strength of Unidirectional Composite Materials Using the Off-axis Three-point Flexure and Off-axis Tensile Tests

2010 ◽  
Vol 44 (21) ◽  
pp. 2487-2507 ◽  
Author(s):  
G. Vargas ◽  
F. Mujika
Keyword(s):  
Shear Strength ◽  
Composite Materials ◽  
Tensile Tests ◽  
Unidirectional Composite ◽  
Point Of View ◽  
Experimental Point ◽  
Plane Shear ◽  
Lift Off ◽  
Flexure Test

The aim of this work is to compare from an experimental point of view the determination of in-plane shear strength of unidirectional composite materials by means of two off-axis tests: three-point flexure and tensile. In the case of the off-axis three-point flexure test, the condition of small displacements and the condition of lift-off between the specimen and the fixture supports have been taken into account. Some considerations regarding stress and displacement fields are presented. The in-plane shear characterization has been performed on a carbon fiber reinforced unidirectional laminate with several fiber orientation angles: 10°, 20°, 30°, and 45°. Test conditions for both off-axis experimental methods, in order to ensure their applicability, are presented. Off-axis flexure test is considered more suitable than off-axis tensile test for the determination of in-plane shear strength.

Features of nonlinear in-plane shear deformation of a unidirectional and orthogonally reinforced polymer sheets of composite materials

2021 ◽  
Vol 87 (5) ◽  
pp. 47-55
Author(s):  
A. O. Polovyi ◽  
N. V. Matiushevski ◽  
N. G. Lisachenko
Keyword(s):  
Experimental Data ◽  
Composite Materials ◽  
Shear Modulus ◽  
Maximum Deviation ◽  
Linear Section ◽  
Stress Strain ◽  
Plane Shear ◽  
End Point ◽  
Reinforced Polymer ◽  
Failure Point

A comparative analysis of typical stress-strain diagrams obtained for in-plain shear of the 25 unidirectional and cross-ply reinforced polymer matrix composites under quasi-static loading was carried out. Three of them were tested in the framework of this study, and the experimental data on other materials were taken from the literature. The analysis of the generalized shear-strength curves showed that most of the tested materials exhibit the similar deformation pattern depending on their initial shear modulus: a linear section is observed at the beginning of loading, whereas further increase of the load decreases the slope of the curve reaching the minimum in the failure point. For the three parameters (end point the linear part, maximum reduced deviation of the diagram, tangent shear modulus at the failure point) characterizing the individual features of the presented stress-strain diagrams, approximating their dependences on the value of the reduced initial shear modulus are obtained. At the characteristic points of the deformation diagrams, boundary conditions are determined that can be used to find the parameters of the approximating functions. A condition is proposed for determination of the end point of the linear section on the experimental stress-strain curve, according to which the maximum deviation between the experimental and calculated (according to Hooke’s law) values of the shear stress in this section is no more than 1%, thus ensuring rather high accuracy of approximation on the linear section of the diagram. The results of this study are recommended to use when developing universal and relatively simple in structure approximating functions that take into account the characteristic properties of the experimental curves of deformation of polymer composite materials under in-plane shear of the sheet. The minimum set of experimental data is required to determine the parameters of these functions.

scholarly journals Strain rate and thermal softening effects in shear testing of AA7075-T6 sheet

2018 ◽  
Vol 183 ◽  
pp. 02037 ◽  
Author(s):  
Taamjeed Rahmaan ◽  
Ping Zhou ◽  
Cliff Butcher ◽  
Michael J. Worswick
Keyword(s):  
Strain Rate ◽  
High Speed ◽  
Rate Sensitivity ◽  
Thermal Conditions ◽  
Shear Loading ◽  
Image Correlation ◽  
High Rate ◽  
Strain Rates ◽  
Shear Testing ◽  
Plane Shear

Shear tests were performed at strain rates ranging from quasi-static (0.01 s-1) to 500 s-1 for AA7075-T6 sheet metal alloy at room temperature. A miniature sized shear specimen was used in this work to perform high strain rate shear testing. Digital image correlation (DIC) techniques were employed to measure the strains in the experiments. At maximum in-plane shear strains greater than 20%, the AA7075-T6 alloy demonstrated a reduced work hardening rate at elevated strain rates. At lower strains, the AA7075-T6 alloy showed mild positive rate sensitivity. The strain to localization (using the Zener-Holloman criterion), measured using the DIC technique, decreased with strain rate in shear loading. The strain at complete failure, however, exhibited an increase at the highest strain rate (500 s-1). The current work also focused on characterization of the thermal conditions occurring during high rate loading in shear with in situ high speed thermal imaging. Experimental results from the highest strain rate (500 s-1) tests showed a notable increase in temperature within the specimen gauge region as a result of the conversion of plastic deformation energy into heat.

Higher order asymptotic homogenization and wave propagation in periodic composite materials

2008 ◽  
Vol 464 (2093) ◽  
pp. 1181-1201 ◽  
Author(s):  
Igor V Andrianov ◽  
Vladimir I Bolshakov ◽  
Vladyslav V Danishevs'kyy ◽  
Dieter Weichert
Keyword(s):  
Composite Materials ◽  
Exact Analytical Solution ◽  
Higher Order ◽  
Square Lattice ◽  
Infinite Plane ◽  
Dimensional Problem ◽  
Asymptotic Homogenization ◽  
Plane Shear ◽  
Frequency Bands ◽  
Periodic Composite

We present an application of the higher order asymptotic homogenization method (AHM) to the study of wave dispersion in periodic composite materials. When the wavelength of a travelling signal becomes comparable with the size of heterogeneities, successive reflections and refractions of the waves at the component interfaces lead to the formation of a complicated sequence of the pass and stop frequency bands. Application of the AHM provides a long-wave approximation valid in the low-frequency range. Solution for the high frequencies is obtained on the basis of the Floquet–Bloch approach by expanding spatially varying properties of a composite medium in a Fourier series and representing unknown displacement fields by infinite plane-wave expansions. Steady-state elastic longitudinal waves in a composite rod (one-dimensional problem allowing the exact analytical solution) and transverse anti-plane shear waves in a fibre-reinforced composite with a square lattice of cylindrical inclusions (two-dimensional problem) are considered. The dispersion curves are obtained, the pass and stop frequency bands are identified.

Out-of-Plane Shear Properties of IM7/8552 Carbon/Epoxy by V-notched Shear Testing

2020 ◽  
Author(s):  
Rudy T. Haluza ◽  
Kevin Koudela ◽  
Charles Bakis ◽  
Daniel O. Adams ◽  
Mark A. Perl ◽  
...  
Keyword(s):  
Shear Testing ◽  
Plane Shear ◽  
Shear Properties ◽  
Out Of Plane
Sign in / Sign up

Export Citation Format

Share Document