Characterization of Elastic-plastic Material Properties for IMC Layer of ENEPIG by Using Reverse Algorithm

2010 ◽  
Author(s):  
Jong-Min Kim ◽  
Hyun-Boo Lee ◽  
Yoon-Suk Chang ◽  
Jae-Boong Choi ◽  
Young-Jin Kim ◽  
...  
Keyword(s):  
Material Properties ◽  
Plastic Material ◽  
Elastic Plastic ◽  
Elastic Plastic Material

Structural Integrity Research for Reactor Pressure Vessel Under In-Vessel Retention of a Core Melt

2016 ◽  
Author(s):  
Yongjian Gao ◽  
Yinbiao He ◽  
Ming Cao ◽  
Yuebing Li ◽  
Shiyi Bao ◽  
...  
Keyword(s):  
Pressure Vessel ◽  
Material Properties ◽  
Power Plants ◽  
Structural Integrity ◽  
Plastic Material ◽  
Plastic Region ◽  
Reactor Pressure Vessel ◽  
Elastic Plastic ◽  
Elastic Plastic Material ◽  
Reactor Pressure

In-Vessel Retention (IVR) is one of the most important severe accident mitigation strategies of the third generation passive Nuclear Power Plants (NPP). It is intended to demonstrate that in the case of a core melt, the structural integrity of the Reactor Pressure Vessel (RPV) is assured such that there is no leakage of radioactive debris from the RPV. This paper studied the IVR issue using Finite Element Analyses (FEA). Firstly, the tension and creep testing for the SA-508 Gr.3 Cl.1 material in the temperature range of 25°C to 1000°C were performed. Secondly, a FEA model of the RPV lower head was built. Based on the assumption of ideally elastic-plastic material properties derived from the tension testing data, limit analyses were performed under both the thermal and the thermal plus pressure loading conditions where the load bearing capacity was investigated by tracking the propagation of plastic region as a function of pressure increment. Finally, the ideal elastic-plastic material properties incorporating the creep effect are developed from the 100hr isochronous stress-strain curves, limit analyses are carried out as the second step above. The allowable pressures at 0 hr and 100 hr are obtained. This research provides an alternative approach for the structural integrity evaluation for RPV under IVR condition.

scholarly journals Characterization of Impacts of Elastic-plastic Spheres

2020 ◽  
Vol 64 (2) ◽  
pp. 165-171
Author(s):  
Bence Szabó ◽  
Attila Kossa
Keyword(s):  
Plastic Material ◽  
Analytical Models ◽  
Material Models ◽  
Elastic Plastic ◽  
Analytical Functions ◽  
Elastic Plastic Material ◽  
Explicit Dynamic ◽  
The Impact ◽  
The Given

This work presents explicit dynamic finite element simulations of various impacts of elastic-plastic solid spheres with flat walls. Different  analytical models describing the mechanics of the impact phenomenon are also presented. Elastic and elastic-plastic material models for the sphere and the wall are considered during the analyses. The applicability of these different models is demonstrated and their accuracies are investigated. Closed-form analytical functions are proposed to describe the relationship between the initial velocity of the sphere and the investigated contact characteristics for the given material models. Analysis is carried out to study the effect of the friction coefficient as well as the angle of impact for various cases.

Analysis of the spherical indentation cycle for elastic–perfectly plastic solids

2004 ◽  
Vol 19 (12) ◽  
pp. 3641-3653 ◽  
Author(s):  
L. Kogut ◽  
K. Komvopoulos
Keyword(s):  
Plastic Deformation ◽  
Finite Element ◽  
Elastic Modulus ◽  
Yield Strength ◽  
Material Properties ◽  
Deformation Behavior ◽  
Plastic Material ◽  
Elastic Plastic ◽  
Loading And Unloading ◽  
Elastic Plastic Material

A finite element analysis of frictionless indentation of an elastic–plastic half-space by a rigid sphere is presented and the deformation behavior during loading and unloading is examined in terms of the interference and elastic–plastic material properties. The analysis yields dimensionless constitutive relationships for the normal load, contact area, and mean contact pressure during loading for a wide range of material properties and interference ranging from the inception of yielding to the initiation of fully plastic deformation. The boundaries between elastic, elastic–plastic, and fully plastic deformation regimes are determined in terms of the interference, mean contact pressure, and reduced elastic modulus-to-yield strength ratio. Relationships for the hardness and associated interference versus elastic–plastic material properties and truncated contact radius are introduced, and the shape of the plastic zone and maximum equivalent plastic strain are interpreted in light of finite element results. The unloading response is examined to evaluate the validity of basic assumptions in traditional indentation approaches used to measure the hardness and reduced elastic modulus of materials. It is shown that knowledge of the deformation behavior under both loading and unloading conditions is essential for accurate determination of the true hardness and reduced elastic modulus. An iterative approach for determining the reduced elastic modulus, yield strength, and hardness from indentation experiments and finite element solutions is proposed as an alternative to the traditional method.

Extraction of elastic–plastic material properties of thin films through nanoindentaion technique with support of numerical methods

2011 ◽  
Vol 51 (6) ◽  
pp. 1046-1053 ◽  
Author(s):  
Łukasz Dowhań ◽  
Artur Wymysłowski ◽  
Paweł Janus ◽  
Magdalena Ekwińska ◽  
Olaf Wittler
Keyword(s):  
Thin Films ◽  
Numerical Methods ◽  
Material Properties ◽  
Plastic Material ◽  
Elastic Plastic ◽  
Elastic Plastic Material

On Determining Elastic Modulus from Instrumented Indentation

2013 ◽  
Vol 668 ◽  
pp. 616-620
Author(s):  
Shuai Huang ◽  
Huang Yuan
Keyword(s):  
Finite Element ◽  
Elastic Modulus ◽  
Plastic Material ◽  
Instrumented Indentation ◽  
Computational Simulations ◽  
Elastic Plastic ◽  
Modified Method ◽  
Plastic Materials ◽  
Elastic Plastic Material ◽  
Elastic Plastic Materials

Computational simulations of indentations in elastic-plastic materials showed overestimate in determining elastic modulus using the Oliver & Pharr’s method. Deviations significantly increase with decreasing material hardening. Based on extensive finite element computations the correlation between elastic-plastic material property and indentation has been carried out. A modified method was introduced for estimating elastic modulus from dimensional analysis associated with indentation data. Experimental verifications confirm that the new method produces more accurate prediction of elastic modulus than the Oliver & Pharr’s method.

scholarly journals Relationship Between Rockwell C Hardness and Inelastic Material Constants

2002 ◽  
Vol 124 (2) ◽  
pp. 179-184 ◽  
Author(s):  
Akihiko Hirano ◽  
Masao Sakane ◽  
Naomi Hamada
Keyword(s):  
Finite Element ◽  
Friction Coefficient ◽  
Strain Hardening ◽  
Yield Stress ◽  
Plastic Material ◽  
Stress And Strain ◽  
Material Constants ◽  
Elastic Plastic ◽  
Elastic Plastic Material ◽  
Hardening Coefficient

This paper describes the relationship between Rockwell C hardness and elastic-plastic material constants by using finite element analyses. Finite element Rockwell C hardness analyses were carried out to study the effects of friction coefficient and elastic-plastic material constants on the hardness. The friction coefficient and Young’s modulus had no influence on the hardness but the inelastic materials constants, yield stress, and strain hardening coefficient and exponent, had a significant influence on the hardness. A new equation for predicting the hardness was proposed as a function of yield stress and strain hardening coefficient and exponent. The equation evaluated the hardness within a ±5% difference for all the finite element and experimental results. The critical thickness of specimen and critical distance from specimen edge in the hardness testing was also discussed in connection with JIS and ISO standards.

Sign in / Sign up

Export Citation Format

Share Document