Kinetics of crack growth in zirconium alloys (II): Stress dependence of the crack growth rate

2010 ◽  
Vol 107 (11) ◽  
pp. 113520 ◽  
Author(s):  
Young S. Kim
Keyword(s):  
Growth Rate ◽  
Crack Growth Rate ◽  
Crack Growth ◽  
Zirconium Alloys ◽  
Stress Dependence ◽  
Kinetics Of

scholarly journals Effect of water flow and depth on fatigue crack growth rate of underwater wet welded low carbon steel SS400

2021 ◽  
Vol 11 (1) ◽  
pp. 329-338 ◽  
Author(s):  
E. Surojo ◽  
J. Anindito ◽  
F. Paundra ◽  
A. R. Prabowo ◽  
E. P. Budiana ◽  
...  
Keyword(s):  
Growth Rate ◽  
Fatigue Crack ◽  
Carbon Steel ◽  
Crack Growth Rate ◽  
Crack Growth ◽  
Water Flow ◽  
Water Depth ◽  
Water Flow Rate ◽  
Low Carbon Steel ◽  
Low Carbon

Abstract Underwater wet welding (UWW) is widely used in repair of offshore constructions and underwater pipelines by the shielded metal arc welding (SMAW) method. They are subjected the dynamic load due to sea water flow. In this condition, they can experience the fatigue failure. This study was aimed to determine the effect of water flow speed (0 m/s, 1 m/s, and 2 m/s) and water depth (2.5 m and 5 m) on the crack growth rate of underwater wet welded low carbon steel SS400. Underwater wet welding processes were conducted using E6013 electrode (RB26) with a diameter of 4 mm, type of negative electrode polarity and constant electric current and welding speed of 90 A and 1.5 mm/s respectively. In air welding process was also conducted for comparison. Compared to in air welded joint, underwater wet welded joints have more weld defects including porosity, incomplete penetration and irregular surface. Fatigue crack growth rate of underwater wet welded joints will decrease as water depth increases and water flow rate decreases. It is represented by Paris's constant, where specimens in air welding, 2.5 m and 5 m water depth have average Paris's constant of 8.16, 7.54 and 5.56 respectively. The increasing water depth will cause the formation of Acicular Ferrite structure which has high fatigue crack resistance. The higher the water flow rate, the higher the welding defects, thereby reducing the fatigue crack resistance.

Fracture and Fatigue Resistance of Ultrafine Grain CuCrZr Alloy Produced ECAP

2006 ◽  
Vol 503-504 ◽  
pp. 811-816 ◽  
Author(s):  
Alexei Vinogradov ◽  
Kazuo Kitagawa ◽  
V.I. Kopylov
Keyword(s):  
Growth Rate ◽  
Crack Growth Rate ◽  
Crack Growth ◽  
Stable Crack Growth ◽  
Ultrafine Grain ◽  
J Integral ◽  
Present Communication ◽  
Angular Pressing ◽  
Fatigue And Fracture ◽  
Anisotropy Of Mechanical Properties

Anisotropy of mechanical properties, fatigue and fracture resistance of precipitation hardened CuCrZr alloy ultrafine (UFG) grained by equal-channel angular pressing (ECAP) is in focus of the present communication. Fracture toughness was estimated in terms of J-integral and the fatigue crack growth rate was quantified. It was found that although the estimated JIC-value appeared lower than that reported in the literature for a reference alloy, the ductility, fracture and crack growth resistance remained satisfactory after ECAP while the tensile strength and fatigue limit improved considerably. The stable crack growth rate did not differ very much for ECAP and reference conventional CuCrZr and no remarkable anisotropy in the stable crack growth was noticed.

scholarly journals Study on the Influence of the Gurson–Tvergaard–Needleman Damage Model on the Fatigue Crack Growth Rate

Metals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1183
Author(s):  
Edmundo R. Sérgio ◽  
Fernando V. Antunes ◽  
Diogo M. Neto ◽  
Micael F. Borges
Keyword(s):  
Growth Rate ◽  
Fatigue Crack ◽  
Crack Growth Rate ◽  
Fatigue Crack Growth ◽  
Plastic Strain ◽  
Crack Growth ◽  
Damage Model ◽  
Crack Tip ◽  
Strength Parameter ◽  
Stress Intensity Factor Range

The fatigue crack growth (FCG) process is usually accessed through the stress intensity factor range, ΔK, which has some limitations. The cumulative plastic strain at the crack tip has provided results in good agreement with the experimental observations. Also, it allows understanding the crack tip phenomena leading to FCG. Plastic deformation inevitably leads to micro-porosity occurrence and damage accumulation, which can be evaluated with a damage model, such as Gurson–Tvergaard–Needleman (GTN). This study aims to access the influence of the GTN parameters, related to growth and nucleation of micro-voids, on the predicted crack growth rate. The results show the connection between the porosity values and the crack closure level. Although the effect of the porosity on the plastic strain, the predicted effect of the initial porosity on the predicted crack growth rate is small. The sensitivity analysis identified the nucleation amplitude and Tvergaard’s loss of strength parameter as the main factors, whose variation leads to larger changes in the crack growth rate.

Fatigue Crack Growth of Alloy 7050-T7451 Plate in L-S Orientation

2012 ◽  
Vol 525-526 ◽  
pp. 221-224
Author(s):  
Rui Bao ◽  
Xiao Chen Zhao ◽  
Ting Zhang ◽  
Jian Yu Zhang
Keyword(s):  
Growth Rate ◽  
Stress Intensity Factor ◽  
Fatigue Crack ◽  
Stress Intensity ◽  
Crack Growth Rate ◽  
Crack Growth ◽  
Growth Characteristics ◽  
Stress Intensity Factor Range ◽  
Constant Amplitude ◽  
Stress Ratios

Experiments have been conducted to investigate the crack growth characteristics of 7050-T7451 aluminium plate in L-S orientation. Two loading conditions are selected, i.e. constant amplitude and constant stress intensity factor range (ΔK). The effects of ΔK-levels and stress ratios (R) on crack splitting are studied. Test data shows that crack splitting could result in the reverse of crack growth rate trend with the increasing R ratio at high ΔK-level. The appearance of crack splitting depends on both ΔK and R.

Sign in / Sign up

Export Citation Format

Share Document