Lamb wave in a thin piezoelectric ceramic plate under the influence of static tensile stress

1975 ◽  
Vol 46 (12) ◽  
pp. 5114-5115 ◽  
Author(s):  
Kohji Toda
Keyword(s):  
Tensile Stress ◽  
Lamb Wave ◽  
Piezoelectric Ceramic ◽  
Ceramic Plate ◽  
Static Tensile ◽  
Static Tensile Stress

Creep Performance of Candidate SiC and Si3N4 Materials for Land-Based, Gas Turbine Engine Components

1997 ◽  
Vol 119 (4) ◽  
pp. 799-806 ◽  
Author(s):  
A. A. Wereszczak ◽  
T. P. Kirkland
Keyword(s):  
Tensile Stress ◽  
Gas Turbine ◽  
Test Data ◽  
Creep Rupture ◽  
Tensile Creep ◽  
Fatigue Stress ◽  
Creep Stress ◽  
Static Tensile ◽  
Static Tensile Stress ◽  
Sintered Silicon

The tensile creep-rupture performance of a commercially available gas pressure sintered silicon nitride (Si3N4) and a sintered silicon carbide (SiC) is examined at 1038, 1150, and 1350°C. These two ceramic materials are candidates for nozzles and combustor tiles that are to be retrofitted in land-based gas turbine engines, and interest exists to investigate their high-temperature mechanical performance over service times up to, and in excess of, 10,000 hours (≈14 months). To achieve lifetimes approaching 10,000 hours for the candidate Si3N4 ceramic, it was found (or it was estimated based on ongoing test data) that a static tensile stress of 300 MPa at 1038 and 1150°C, and a stress of 125 MPa at 1350°C cannot be exceeded. For the SiC ceramic, it was estimated from ongoing test data that a static tensile stress of 300 MPa at 1038°C, 250 MPa at 1150°C, and 180 MPa at 1350°C cannot be exceeded. The creep-stress exponents for this Si3N4 were determined to be 33, 17, and 8 for 1038, 1150, and 1350°C, respectively. The fatigue-stress exponents for the Si3N4 were found to be equivalent to the creep exponents, suggesting that the fatigue mechanism that ultimately causes fracture is controlled and related to the creep mechanisms. Little success was experienced at generating failures in the SiC after several decades of time through exposure to appropriate tensile stress; it was typically observed that if failure did not occur on loading, then the SiC specimens most often did not creep-rupture. However, creep-stress exponents for the SiC were determined to be 57, 27, and 11 for 1038, 1150, and 1350°C, respectively. For SiC, the fatigue-stress exponents did not correlate as well with creep-stress exponents. Failures that occurred in the SiC were a result of slow crack growth that was initiated from the specimen’s surface.

Study of the hydroacoustic emitter based on the antisymmetric lamb wave in a piezoelectric ceramic plate

2011 ◽  
Vol 56 (11) ◽  
pp. 1382-1386 ◽  
Author(s):  
I. E. Kuznetsova ◽  
B. D. Zaitsev ◽  
I. A. Borodina ◽  
V. V. Kolesov ◽  
A. I. Sknarya ◽  
...  
Keyword(s):  
Lamb Wave ◽  
Piezoelectric Ceramic ◽  
Ceramic Plate

Dislocation nucleation from near surface void under static tensile stress in Cu

2011 ◽  
Vol 110 (2) ◽  
pp. 023509 ◽  
Author(s):  
A. S. Pohjonen ◽  
F. Djurabekova ◽  
K. Nordlund ◽  
A. Kuronen ◽  
S. P. Fitzgerald
Keyword(s):  
Tensile Stress ◽  
Dislocation Nucleation ◽  
Near Surface ◽  
Static Tensile ◽  
Static Tensile Stress

Creep Performance of Candidate SiC and Si3N4 Materials for Land-Based, Gas Turbine Engine Components

1996 ◽  
Author(s):  
Andrew A. Wereszczak ◽  
Timothy P. Kirkland
Keyword(s):  
Tensile Stress ◽  
Gas Turbine ◽  
Test Data ◽  
Creep Rupture ◽  
Tensile Creep ◽  
Fatigue Stress ◽  
Creep Stress ◽  
Static Tensile ◽  
Static Tensile Stress ◽  
Sintered Silicon

The tensile creep-rupture performance of a commercially available gas pressure sintered silicon nitride (Si3N4) and a sintered silicon carbide (SiC) is examined at 1038, 1150, and 1350°C. These two ceramic materials are candidates for nozzles and combustor tiles that are to be retrofitted in land-based gas turbine engines, and interest exists to investigate their high temperature mechanical performance over service-times up to, and in excess of, 10000 hours (≈ 14 months). To achieve lifetimes approaching 10000 hours for the candidate Si3N4 ceramic, it was found (or it was estimated based on ongoing test data) that a static tensile stress of 300 MPa at 1038 and 1150°C, and a stress of 125 MPa at 1350°C cannot be exceeded. For the SiC ceramic, it was estimated from ongoing test data that a static tensile stress of 300 MPa at 1038°C, 250 MPa at 1150°C, and 180 MPa at 1350°C cannot be exceeded. The creep-stress exponents for this Si3N4 were determined to be 33, 17, and 8 for 1038, 1150, and 1350°C, respectively. The fatigue-stress exponents for the Si3N4 were found to be equivalent to the creep exponents, suggesting that the fatigue mechanism that ultimately causes fracture is controlled and related to the creep mechanisms. Little success was experienced at generating failures in the SiC after several decades of time through exposure to appropriate tensile stress; it was typically observed that if failure did not occur on loading, then the SiC specimens most often did not creep-rupture. However, creep-stress exponents for the SiC were determined to be 57, 27, and 11 for 1038, 1150, and 1350°C, respectively. For SiC, the fatigue-stress exponents did not correlate as well with creep-stress exponents. Failures that occurred in the SiC were a result of slow crack growth that initiated from the specimen’s surface.

Sign in / Sign up

Export Citation Format

Share Document