On vortical flows shedding from a bluff body with a wavy trailing edge

2008 ◽  
Vol 20 (6) ◽  
pp. 064102 ◽  
Author(s):  
Jinsheng Cai ◽  
Tat Loon Chng ◽  
Her Mann Tsai
Keyword(s):  
Bluff Body ◽  
Trailing Edge ◽  
Vortical Flows

On turbulent separation in the flow past a bluff body

1992 ◽  
Vol 241 ◽  
pp. 443-467 ◽  
Author(s):  
A. Neish ◽  
F. T. Smith
Keyword(s):  
Large Scale ◽  
Bluff Body ◽  
Separated Flow ◽  
Small Scale ◽  
Supporting Evidence ◽  
Turbulent Regime ◽  
Trailing Edge ◽  
Flow Past ◽  
Starting Point ◽  
Turbulence Factor

The basic model problem of separation as predicted by the time-mean boundary-layer equations is studied, with the Cebeci-Smith model for turbulent stresses. The changes between laminar and turbulent flow are investigated by means of a turbulence ‘factor’ which increases from zero for laminar flow to unity for the fully turbulent regime. With an attached-flow starting point, a small increase in the turbulence factor above zero is found to drive the separation singularity towards the trailing edge or rear stagnation point for flow past a circular cylinder, according to both computations and analysis. A separated-flow starting point is found to produce analogous behaviour for the separation point. These findings lead to the suggestion that large-scale separation need not occur at all in the fully turbulent regime at sufficiently high Reynolds number; instead, separation is of small scale, confined near the trailing edge. Comments on the generality of this suggestion are presented, along with some supporting evidence from other computations. Further, the small scale involved theoretically has values which seem reasonable in practical terms.

Production and Development of Secondary Flows and Losses Within a Three Dimensional Turbine Stator Cascade

1985 ◽  
Author(s):  
A. Yamamoto ◽  
R. Yanagi
Keyword(s):  
Three Dimensional ◽  
Quantitative Information ◽  
Secondary Flows ◽  
Suction Surface ◽  
Trailing Edge ◽  
Loss Mechanism ◽  
Flow Measurements ◽  
Aerodynamic Loss ◽  
Vortical Flows ◽  
Turbine Stator

Using five-hole pitot tubes, detailed flow measurements were made before, within and after a low-speed three-dimensional turbine stator blade row to obtain quantitative information on the aerodynamic loss mechanism. Qualitative flow visualization tests and endwall static pressure measurements were also made. An analysis of the tests revealed that many vortical flows promote loss generation. Within a large part of the cascade, a major loss process could be explained simply as the migration of boundary layer low energy fluids from surrounding walls (endwalls and blade surfaces) to the blade suction surface near the trailing edge. On the other hand, complexity exists after the cascade and in the vortical flows near the trailing edge. The strong trailing shedding vortices affect upstream flow fields within the cascade. Detailed flow surveys within the cascade under the effects of blade tip leakage flows are also included.

A study of three-dimensional aspects of vortex shedding from a bluff body with a mild geometric disturbance

1997 ◽  
Vol 330 ◽  
pp. 85-112 ◽  
Author(s):  
N. TOMBAZIS ◽  
P. W. BEARMAN
Keyword(s):  
Reynolds Number ◽  
Vortex Shedding ◽  
Bluff Body ◽  
Vortex Formation ◽  
Three Dimensional ◽  
Base Pressure ◽  
Trailing Edge ◽  
Blunt Trailing Edge ◽  
Trailing Edges ◽  
Mode Transitions

Experiments have been carried out to study the three-dimensional characteristics of vortex shedding from a half-ellipse shape with a blunt trailing edge. In order to control the occurrence of vortex dislocations, the trailing edges of the models used were constructed with a series of periodic waves across their spans. Flow visualization was carried out in a water tunnel at a Reynolds number of 2500, based on trailing-edge thickness. A number of shedding modes were observed and the sequence of mode transitions recorded. Quantitative data were obtained from wind tunnel measurements performed at a Reynolds number of 40000. Two shedding frequencies were recorded with the higher frequency occurring at spanwise positions coinciding with minima in the chord. At these same positions the base pressure was lowest and the vortex formation length longest. Arguments are put forward to explain these observations. It is shown that the concept of a universal Strouhal number holds, even when the flow is three-dimensional. The spanwise variation in time-average base pressure is predicted using the estimated amount of time the flow spends at the two shedding frequencies.

Interaction and acoustics of separated flows from a D-shaped bluff body

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Guangyuan Huang ◽  
Ka Him Seid ◽  
Zhigang Yang ◽  
Randolph Chi Kin Leung
Keyword(s):  
Vortex Shedding ◽  
Bluff Body ◽  
Leading Edge ◽  
Separated Flows ◽  
Pressure Waves ◽  
Bluff Bodies ◽  
Trailing Edge ◽  
Content Type ◽  
Trailing Edges ◽  
Edge Vortex

Purpose For flow around elongated bluff bodies, flow separations would occur over both leading and trailing edges. Interactions between these two separations can be established through acoustic perturbation. In this paper, the flow and the acoustic fields of a D-shaped bluff body (length-to-height ratio L/H = 3.64) are investigated at height-based Reynolds number Re = 23,000 by experimental and numerical methods. The purpose of this paper is to study the acoustic feedback in the interaction of these two separated flows. Design/methodology/approach The flow field is measured by particle image velocimetry, hotwire velocimetry and surface oil flow visualization. The acoustic field is modeled in two dimensions by direct aeroacoustic simulation, which solves the compressible Navier–Stokes equations. The simulation is validated against the experimental results. Findings Separations occur at both the leading and the trailing edges. The leading-edge separation point and the reattaching flow oscillate in accordance with the trailing-edge vortex shedding. Significant pressure waves are generated at the trailing edge by the vortex shedding rather than the leading-edge vortices. Pressure-based cross-correlation analysis is conducted to clarify the effect of the pressure waves on the leading-edge flow structures. Practical implications The understanding of interactions of separated flows over elongated bluff bodies helps to predict aerodynamic drag, structural vibration and noise in engineering applications, such as the aerodynamics of buildings, bridges and road vehicles. Originality/value This paper clarifies the influence of acoustic perturbations in the interaction of separated flows over a D-shaped bluff body. The contribution of the leading- and the trailing-edge vortex in generating acoustic perturbations is investigated as well.

Measurements of Bluff Body Wake Flow Around a Conformable Flow Control Surface

2003 ◽  
Author(s):  
David A. Ericson ◽  
Michael Jonson ◽  
Gary Koopmann
Keyword(s):  
Flow Control ◽  
Vortex Shedding ◽  
Flow Separation ◽  
Bluff Body ◽  
The Body ◽  
Control Surface ◽  
Periodic Flow ◽  
Two Dimensional ◽  
Trailing Edge ◽  
Shedding Frequency

The vortex street is a unique type of unsteady flow separation seen commonly in flow over a bluff body with a characteristic periodic wake. A consequence of the periodic flow is that the drag and lift forces acting on the body also oscillate periodically. When the wake shedding frequency is near a structural frequency, flow induced resonance will occur. The continuing interest in the study of vortex street generation is propelled by the ever-present nature of these flows in a variety of applications including aerodynamics, hydrodynamics and underwater acoustics. Recent advances in material science and the development of high power density actuators have led to the study of adaptive structure technology wherein the vorticity of periodic flows can be actively controlled by changing the ‘bluffness’ or shape of the body. In this paper, the development and experimental testing of a two-dimensional shape-variable flow control surface are discussed in relation to the generation and manipulation of periodic flow separation. Two series of wind tunnel tests were designed to evaluate the potential of the morphing structure that replaced a section of the trailing edge of a symmetric airfoil. The test section successfully demonstrated a smooth transition between three prescribed trailing edge profiles ranging from sharp to blunt. Unsteady pressure spectra were measured near the trailing edge for three different shape profiles over a range of speeds between 50 and 110 ft/s. The measured pressure spectra amplitudes were compared to previously-published surface pressure spectra of a similar, two-dimensional, blunt edge foil. A second set of tests was performed to measure the resulting flow field in the direction transverse to the flow and downstream from the airfoil. Velocity measurements were made using a traversing hot-wire probe at three trailing edge configurations and speeds of 50, 70 and 90 ft/s. The corresponding Reynolds number based on wake thickness ranged from 3.9–9.8 × 104. Measured vortex shedding frequencies varied between approximately 50 to 130 Hz at the different trailing edge profiles. This type of change in the vortex shedding frequency can be used to reduce flow-induced vibration and its associated noise generation by avoiding shedding frequencies at operating speeds that coincide with airfoil resonances.

Sign in / Sign up

Export Citation Format

Share Document