scholarly journals THERMAL-MECHANICAL RESPONSE OF CRACKED SATIN WEAVE CFRP COMPOSITES AT CRYOGENIC TEMPERATURES

2008 ◽  
Author(s):  
S. Watanabe ◽  
Y. Shindo ◽  
F. Narita ◽  
T. Takeda ◽  
U. (Balu) Balachandran ◽  
...  
Keyword(s):  
Mechanical Response ◽  
Cryogenic Temperatures ◽  
Cfrp Composites

An Experimental Study of the Mechanical Response of Frozen Biological Tissues at Cryogenic Temperatures

Cryobiology ◽  
1996 ◽  
Vol 33 (4) ◽  
pp. 472-482 ◽  
Author(s):  
YOED RABIN ◽  
Paul S. Steif ◽  
Michael J. Taylor ◽  
Thomas B. Julian ◽  
Norman Wolmark
Keyword(s):  
Experimental Study ◽  
Mechanical Response ◽  
Biological Tissues ◽  
Cryogenic Temperatures

Cryogenic mechanical response of multilayer satin weave CFRP composites with cracks

2008 ◽  
Vol 44 (4) ◽  
pp. 331-340 ◽  
Author(s):  
S. Watanabe ◽  
Y. Shindo ◽  
T. Takeda ◽  
F. Narita
Keyword(s):  
Mechanical Response ◽  
Cfrp Composites

Cryogenic atomic force microscopy

1991 ◽  
Vol 49 ◽  
pp. 54-55
Author(s):  
K. A. Fisher ◽  
M. G. L. Gustafsson ◽  
M. B. Shattuck ◽  
J. Clarke
Keyword(s):  
Room Temperature ◽  
Rapid Freezing ◽  
Cryogenic Temperatures ◽  
Soft Or ◽  
Electrically Conductive ◽  
Force Microscopy ◽  
Flexible Molecules ◽  
Advantages And Disadvantages ◽  
Atomic Force ◽  
Chemical Perturbation

The atomic force microscope (AFM) is capable of imaging electrically conductive and non-conductive surfaces at atomic resolution. When used to image biological samples, however, lateral resolution is often limited to nanometer levels, due primarily to AFM tip/sample interactions. Several approaches to immobilize and stabilize soft or flexible molecules for AFM have been examined, notably, tethering coating, and freezing. Although each approach has its advantages and disadvantages, rapid freezing techniques have the special advantage of avoiding chemical perturbation, and minimizing physical disruption of the sample. Scanning with an AFM at cryogenic temperatures has the potential to image frozen biomolecules at high resolution. We have constructed a force microscope capable of operating immersed in liquid n-pentane and have tested its performance at room temperature with carbon and metal-coated samples, and at 143° K with uncoated ferritin and purple membrane (PM).

Comparison of Substructures Between Uniaxial and Biaxial Deformation in 1100-0 Aluminum

1981 ◽  
Vol 39 ◽  
pp. 52-53
Author(s):  
D. L. Rohr ◽  
S. S. Hecker
Keyword(s):  
Plastic Strain ◽  
Cell Walls ◽  
Room Temperature ◽  
Mechanical Response ◽  
Biaxial Tension ◽  
Initial Deformation ◽  
Uniaxial Deformation ◽  
Biaxial Deformation ◽  
Stress States ◽  
Comprehensive Study

As part of a comprehensive study of microstructural and mechanical response of metals to uniaxial and biaxial deformations, the development of substructure in 1100 A1 has been studied over a range of plastic strain for two stress states.Specimens of 1100 aluminum annealed at 350 C were tested in uniaxial (UT) and balanced biaxial tension (BBT) at room temperature to different strain levels. The biaxial specimens were produced by the in-plane punch stretching technique. Areas of known strain levels were prepared for TEM by lapping followed by jet electropolishing. All specimens were examined in a JEOL 200B run at 150 and 200 kV within 24 to 36 hours after testing.The development of the substructure with deformation is shown in Fig. 1 for both stress states. Initial deformation produces dislocation tangles, which form cell walls by 10% uniaxial deformation, and start to recover to form subgrains by 25%. The results of several hundred measurements of cell/subgrain sizes by a linear intercept technique are presented in Table I.

Construction of plastic contact deformation maps on ceramics: a case study on aluminum nitride

1996 ◽  
Vol 54 ◽  
pp. 636-637
Author(s):  
D. L. Callahan
Keyword(s):  
Plastic Deformation ◽  
Aluminum Nitride ◽  
Mechanical Response ◽  
Three Dimensional ◽  
Bright Field Image ◽  
Perfectly Plastic ◽  
Contrast Analysis ◽  
Deformation Patterns

Modern polishing, precision machining and microindentation techniques allow the processing and mechanical characterization of ceramics at nanometric scales and within entirely plastic deformation regimes. The mechanical response of most ceramics to such highly constrained contact is not predictable from macroscopic properties and the microstructural deformation patterns have proven difficult to characterize by the application of any individual technique. In this study, TEM techniques of contrast analysis and CBED are combined with stereographic analysis to construct a three-dimensional microstructure deformation map of the surface of a perfectly plastic microindentation on macroscopically brittle aluminum nitride.The bright field image in Figure 1 shows a lg Vickers microindentation contained within a single AlN grain far from any boundaries. High densities of dislocations are evident, particularly near facet edges but are not individually resolvable. The prominent bend contours also indicate the severity of plastic deformation. Figure 2 is a selected area diffraction pattern covering the entire indentation area.

Sign in / Sign up

Export Citation Format

Share Document