The Application of Synthetically Focused Imaging Techniques for High Resolution Guided Wave Pipe Inspection

2007 ◽  
Author(s):  
J. Davies ◽  
P. Cawley
Keyword(s):  
High Resolution ◽  
Imaging Techniques ◽  
Guided Wave ◽  
Pipe Inspection

High resolution guided wave pipe inspection

2009 ◽  
Author(s):  
Alexander Velichko ◽  
Paul D. Wilcox
Keyword(s):  
High Resolution ◽  
Guided Wave ◽  
Pipe Inspection

Minimum Entropy Deconvolution of Guided Wave Signals in Pipe Inspection

2012 ◽  
Vol 433-440 ◽  
pp. 6403-6408
Author(s):  
Chang Feng Wang ◽  
Yan Feng Geng
Keyword(s):  
Signal Processing ◽  
High Resolution ◽  
Reflection Coefficient ◽  
Pipe Wall ◽  
Guided Wave ◽  
Minimum Entropy ◽  
Reasonable Accuracy ◽  
Pipe Inspection ◽  
Reflected Waves ◽  
Set Up

It is difficult to achieve high resolution for guided wave signals used in pipe inspection. The main reasons include overlap of the reflected waves, diversity of the guided wave’s mode and so on. This paper presents a minimum entropy deconvolution algorithm to solve the problem caused by low resolution of the measured signals. Some experiments were carried out to validate the algorithm. The experimental set-up consists of two pipes, one excitor and two accelerometers. The excitor was used to generate the guided wave signals. Two accelerometers were attached to the pipe end and pipe wall respectively，and were used to measure the guided wave signals. Results show that good estimate of the reflection coefficient is obtained and the resolution of measured signals has been improved. As a result, the length of two pipe samples has been calculated with a reasonable accuracy and the position of the defect in experimental pipe has also been acertained. All of these show a new efficient way for guided wave signal processing in pipe inspection.

High-resolution topographic SEM and radiation damage: The rationale for using low beam voltage

1992 ◽  
Vol 50 (2) ◽  
pp. 1278-1279
Author(s):  
James Pawley ◽  
David Joy
Keyword(s):  
High Resolution ◽  
Imaging Techniques ◽  
Morphological Structure ◽  
Radiation Sensitivity ◽  
Beam Specimen ◽  
Measured Signal ◽  
Practical Consideration ◽  
Interaction Volume ◽  
Impact Area ◽  
Signal Contrast

The scanning electron microscope (SEM) builds up an image by sampling contiguous sub-volumes near the surface of the specimen. A fine electron beam selectively excites each sub-volume and then the intensity of some resulting signal is measured and then plotted as a corresponding intensity in an image. The spatial resolution of such an image is limited by at least three factors. Two of these determine the size of the interaction volume: the size of the electron probe and the extent to which detectable signal is excited from locations remote from the beam impact area. A third limitation emerges from the fact that the probing beam is composed of a number of discrete particles and therefore that the accuracy with which any detectable signal can be measured is limited by Poisson statistics applied to this number (or to the number of events actually detected if this is smaller). As in all imaging techniques, the limiting signal contrast required to recognize a morphological structure is constrained by this statistical consideration. The only way to overcome this limit is to increase either the contrast of the measured signal or the number of beam/specimen interactions detected. Unfortunately, these interactions deposit ionizing radiation that may damage the very structure under investigation. As a result, any practical consideration of the high resolution performance of the SEM must consider not only the size of the interaction volume but also the contrast available from the signal producing the image and the radiation sensitivity of the specimen.

Recent applications of TEM to the study of interfaces

1990 ◽  
Vol 48 (4) ◽  
pp. 308-309
Author(s):  
C. Barry Carter
Keyword(s):  
High Resolution ◽  
Sample Preparation ◽  
Grain Boundaries ◽  
Diffuse Scattering ◽  
Imaging Techniques ◽  
Amorphous Material ◽  
Contrast Imaging ◽  
Current State ◽  
Actual Nature ◽  
High Resolution Images

This paper will review the current state of understanding of interface structure and highlight some of the future needs and problems which must be overcome. The study of this subject can be separated into three different topics: 1) the fundamental electron microscopy aspects, 2) material-specific features of the study and 3) the characteristics of the particular interfaces. The two topics which are relevant to most studies are the choice of imaging techniques and sample preparation. The techniques used to study interfaces in the TEM include high-resolution imaging, conventional diffraction-contrast imaging, and phase-contrast imaging (Fresnel fringe images, diffuse scattering). The material studied affects not only the characteristics of the interfaces (through changes in bonding, etc.) but also the method used for sample preparation which may in turn have a significant affect on the resulting image. Finally, the actual nature and geometry of the interface must be considered. For example, it has become increasingly clear that the plane of the interface is particularly important whenever at least one of the adjoining grains is crystalline.A particularly productive approach to the study of interfaces is to combine different imaging techniques as illustrated in the study of grain boundaries in alumina. In this case, the conventional imaging approach showed that most grain boundaries in ion-thinned samples are grooved at the grain boundary although the extent of this grooving clearly depends on the crystallography of the surface. The use of diffuse scattering (from amorphous regions) gives invaluable information here since it can be used to confirm directly that surface grooving does occur and that the grooves can fill with amorphous material during sample preparation (see Fig. 1). Extensive use of image simulation has shown that, although information concerning the interface can be obtained from Fresnel-fringe images, the introduction of artifacts through sample preparation cannot be lightly ignored. The Fresnel-fringe simulation has been carried out using a commercial multislice program (TEMPAS) which was intended for simulation of high-resolution images.

scholarly journals BIMG-04. MAPPING HETEROGENEITY OF HIGH-GRADE GLIOMA METABOLISM USING HIGH RESOLUTION 7T MRSI

2021 ◽  
Vol 3 (Supplement_1) ◽  
pp. i1-i1
Author(s):  
Gilbert Hangel ◽  
Cornelius Cadrien ◽  
Philipp Lazen ◽  
Sukrit Sharma ◽  
Julia Furtner ◽  
...  
Keyword(s):  
High Resolution ◽  
Imaging Techniques ◽  
Basis Set ◽  
Metabolic Imaging ◽  
Tumor Segmentation ◽  
Low Grade ◽  
High Grade ◽  
Isotropic Resolution ◽  
Contrast Enhanced ◽  
Definition Of

Abstract OBJECTIVES Neurosurgical resection in gliomas depends on the precise preoperative definition of the tumor and its margins to realize a safe maximum resection that translates into a better patient outcome. New metabolic imaging techniques could improve this delineation as well as designate targets for biopsies. We validated the performance of our fast high-resolution whole-brain 3D-magnetic resonance spectroscopic imaging (MRSI) method at 7T in high-grade gliomas (HGGs) as first step to this regard. METHODS We measured 23 patients with HGGs at 7T with MRSI covering the whole cerebrum with 3.4mm isotropic resolution in 15 min. Quantification used a basis-set of 17 neurochemical components. They were evaluated for their reliability/quality and compared to neuroradiologically segmented tumor regions-of-interest (necrosis, contrast-enhanced, non-contrast-enhanced+edema, peritumoral) and histopathology (e.g., grade, IDH-status). RESULTS We found 18/23 measurements to be usable and ten neurochemicals quantified with acceptable quality. The most common denominators were increases of glutamine, glycine, and total choline as well as decreases of N-acetyl-aspartate and total creatine over most tumor regions. Other metabolites like taurine and serine showed mixed behavior. We further found that heterogeneity in the metabolic images often continued into the peritumoral region. While 2-hydroxy-glutarate could not be satisfyingly quantified, we found a tendency for a decrease of glutamate in IDH1-mutant HGGs. DISCUSSION Our findings corresponded well to clinical tumor segmentation but were more heterogeneous and often extended into the peritumoral region. Our results corresponded to previous knowledge, but with previously not feasible resolution. Apart from glycine/glutamine and their role in glioma progression, more research on the connection of glutamate and others to specific mutations is necessary. The addition of low-grade gliomas and statistical ROI analysis in a larger cohort will be the next important steps to define the benefits of our 7T MRSI approach for the definition of spatial metabolic tumor profiles.

Guided Wave Focusing Mechanics in Pipe

2003 ◽  
Author(s):  
Takahiro Hayashi ◽  
Koichiro Kawashima ◽  
Zongqi Sun ◽  
Joseph L. Rose
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Guided Waves ◽  
Wave Structure ◽  
Guided Wave ◽  
Pipe Inspection ◽  
Specific Point ◽  
Wave Focusing ◽  
Beam Focusing ◽  
Subsequent Time

Guided waves can be used in pipe inspection over long distances. Presented in this paper is a beam focusing technique to improve the S/N ratio of the reflection from a tiny defect. Focusing is accomplished by using non-axisymmetric waveforms and subsequent time delayed superposition at a specific point in a pipe. A semi-analytical finite element method is used to present wave structure in the pipe. Focusing potential is also studied with various modes and frequencies.

High-Resolution Magnetic Resonance Imaging of the Human Median Nerve

2004 ◽  
Vol 18 (2) ◽  
pp. 80-87 ◽  
Author(s):  
Archie Heddings ◽  
Mehmet Bilgen ◽  
Randolph Nudo ◽  
Bruce Toby ◽  
Terence McIff ◽  
...  
Keyword(s):  
Magnetic Resonance Imaging ◽  
Magnetic Resonance ◽  
High Resolution ◽  
Peripheral Nerve ◽  
Median Nerve ◽  
Ex Vivo ◽  
Imaging Techniques ◽  
Proton Density ◽  
Resonance Imaging ◽  
Imaging Protocols

Objectives. It is widely accepted that peripheral nerve repairs performed within 6 weeks of injury have much better outcomes than those performed at later dates. However, there is no diagnostic technique that can determine if a traumatic peripheral nerve injury requires surgical intervention in the early postinjury phase. The objective of this article was to determine whether novel, noninvasive magnetic resonance imaging techniques could demonstrate the microstructure of human peripheral nerves that is necessary for determining prognosis and determining if surgery is indicated following traumatic injury. Methods. Ex vivo magnetic resonance imaging protocols were developed on a 9.4-T research scanner using spin-echo proton density and gradient-echo imaging sequences and a specially designed, inductively coupled radio frequency coil. These imaging protocols were applied to in situ imaging of the human median nerve in 4 fresh-frozen cadaver arms. Results. Noninvasive high-resolution images of the human median nerve were obtained. Structures in the nerve that were observed included fascicles, interfascicular epineurium, perineurium, and intrafascicular septations. Conclusion. Application of these imaging techniques to clinical scanners could provide physicians with a tool that is capable of grading the severity of nerve injuries and providing indications for surgery in the early postinjury phase.

Accurate Thickness Inversion of Corrosion Using A1 Lamb Wave

2021 ◽  
Author(s):  
Min Lin ◽  
Yang Liu
Keyword(s):  
High Resolution ◽  
Oil And Gas ◽  
Residual Life ◽  
Early Stage ◽  
Corrosion Damage ◽  
Oil And Gas Industry ◽  
Forward Modeling ◽  
Guided Wave ◽  
Velocity Inversion ◽  
Wave Tomography

Abstract Corrosion is one of the most critical issues in the oil and gas industry, leading to severe environmental and economic problems. Due to the high cost and serious safety risk of corrosion, it is essential to improve current corrosion testing techniques to detect corrosion damages at an early stage. Guided wave tomography (GWT) demonstrates its great potential to inspect and quantify the corrosion damage. GWT is capable of determining the residual life of corrosion structures by quantifying the remaining wall thickness. In this paper, an accurate guided wave tomography technique incorporating full waveform inversion (FWI) and higher-order Lamb waves (A1 mode) is presented for plate-like structures, which is able to get high-resolution reconstruction results. The technique consists of three steps: forward modeling, velocity inversion and thickness reconstruction. The forward modeling is computed by solving the elastic full-wave equations in 2-D time domain by using the finite difference method. High-resolution phase velocity inversion can then be obtained by minimizing the waveform misfit function between simulated and recorded data using a second order optimization method, which updates the velocity model from low to high frequencies iteratively. Finally, the velocity variations can be transformed into depth profiles by using the dispersive characteristics of ultrasonic guided waves; therefore, the thickness reconstruction can be obtained. The numerical simulations are performed on an aluminum plate with a complicated corrosion defect. By comparing the thickness reconstruction maps using both A1 and A0 modes, the results demonstrate that FWI with A1 mode can achieve significantly better resolution of corrosion imaging than that with A0 mode.

Sign in / Sign up

Export Citation Format

Share Document