scholarly journals Suppression of insertion loss by slit patterning of a magnetic film in a CoFeB/polyimide hybrid thin-film coplanar line for a rf impedance matching device

2006 ◽  
Vol 99 (8) ◽  
pp. 08P508 ◽  
Author(s):  
Hidetoshi Nakayama ◽  
Tomohiro Yamamoto ◽  
Yuko Mizoguchi ◽  
Masahiro Nakazawa ◽  
Toshiro Sato ◽  
...  
Keyword(s):  
Thin Film ◽  
Insertion Loss ◽  
Impedance Matching ◽  
Magnetic Film ◽  
Hybrid Thin Film ◽  
Coplanar Line

A multi-octave microwave 6-bit true time delay with low amplitude and delay variation in 65 nm CMOS

2021 ◽  
pp. 1-10
Author(s):  
Yakov Gutkin ◽  
Asher Madjar ◽  
Emanuel Cohen
Keyword(s):  
Time Delay ◽  
Insertion Loss ◽  
Impedance Matching ◽  
Least Significant Bit ◽  
Delay Cell ◽  
True Time Delay ◽  
Unit Cells ◽  
True Time ◽  
And Performance ◽  
Low Amplitude

Abstract In this paper, we describe the design, layout, and performance of a 6-bit TTD (true time delay) chip operating over the entire band of 2–18 GHz. The 1.15 mm2 chip is implemented using TSMC foundry 65 nm technology. The least significant bit is 1 ps. The design is based on the concept of all-pass network with some modifications intended to reduce the number of unit cells. Thus, the first three bits are implemented in a single delay cell. A peaking buffer amplifier between bit 4 and bit 5 is used for impedance matching and partial compensation of the insertion loss slope. The rms delay error of the TTD is <1 ps over most of the frequency band and insertion loss is between 2.5 and 6.3 dB for all 64 states.

Organic-inorganic hybrid thin film light-emitting devices: interfacial engineering and device physics

2021 ◽  
Author(s):  
Chunxiu Zang ◽  
Mengxin Xu ◽  
Letian Zhang ◽  
Shihao Liu ◽  
Wenfa Xie
Keyword(s):  
Thin Film ◽  
Quantum Dots ◽  
Sandwich Structure ◽  
Device Physics ◽  
Hybrid Thin Film ◽  
Inorganic Hybrid ◽  
Light Emitting ◽  
Light Emitting Devices ◽  
Interfacial Engineering ◽  
Organic Light

Thin film light-emitting devices (LEDs) with sandwich structure, such as organic light emitting devices (OLEDs), quantum dots LEDs (QLEDs) and perovskite LEDs (PeLEDs), have attracted wide attentions because of their...

Towards solution-processed ambipolar hybrid thin-film transistors based on ZnO nanoparticles and P3HT polymer

2013 ◽  
Vol 58 ◽  
pp. 144-153 ◽  
Author(s):  
Abdou Karim Diallo ◽  
Meriem Gaceur ◽  
Nicolas Berton ◽  
Olivier Margeat ◽  
Jörg Ackermann ◽  
...  
Keyword(s):  
Thin Film ◽  
Zno Nanoparticles ◽  
Thin Film Transistors ◽  
Solution Processed ◽  
Hybrid Thin Film

Overcoats and Lubrication for Thin Film Disks

MRS Bulletin ◽  
1990 ◽  
Vol 15 (3) ◽  
pp. 45-52 ◽  
Author(s):  
A.M. Homola ◽  
C.M. Mate ◽  
G.B. Street
Keyword(s):  
Thin Film ◽  
Data Storage ◽  
Magnetic Particles ◽  
Areal Density ◽  
Magnetic Film ◽  
Alloy Thin Film ◽  
Magnetic Media ◽  
Disk Interface ◽  
Storage Devices ◽  
Particulate Media

Metallic alloy thin film media and ever decreasing head-to-media spacing make severe demands on storage devices. Decreasing head-to-media separation is critical for high storage densities but it also leads to increased slider-disk interactions, which can cause slider and disk wear or even head crashes. Wear can also occur when drives start and stop when the slider contacts the disk at relatively high speeds. The reliability and durability of thin film disks, which provide much higher areal density than conventional oxide disks with particulate media, are achieved by the use of very thin overcoat materials and surface lubricants. This article summarizes the approaches taken in the industry to enhance the tribological performance of magnetic media, with special emphasis on the basic understanding of the processes occurring at the slider-disk interface.The continuous rise in the demand for storage capacity at a competitive price is the prime motivator of the changes we have seen in the data storage industry. It is clearly stimulating the present move away from particulate media, which has long dominated all fields of data storage, i.e., tape, rigid, and flexible disks, to the thin film storage media. Particulate storage devices use magnetic media formulated by dispersing magnetic particles, usually iron oxides, in an organic binder. In thin film storage devices, the storage medium is a continuous magnetic film, usually a cobalt alloy, made either by sputtering or by electroless plating.

Sign in / Sign up

Export Citation Format

Share Document