Structural and electrical evolution of gate dielectric breakdown observed by conductive atomic force microscopy

2006 ◽  
Vol 88 (3) ◽  
pp. 032906 ◽  
Author(s):  
Li Zhang ◽  
Yuichiro Mitani
Keyword(s):  
Atomic Force Microscopy ◽  
Gate Dielectric ◽  
Dielectric Breakdown ◽  
Conductive Atomic Force Microscopy ◽  
Force Microscopy ◽  
Atomic Force

Direct Observation of Dielectric Breakdown Spot in Thermal Oxides on 4H-SiC(0001) Using Conductive Atomic Force Microscopy

2010 ◽  
Vol 645-648 ◽  
pp. 821-824 ◽  
Author(s):  
Kohei Kozono ◽  
Takuji Hosoi ◽  
Yusuke Kagei ◽  
Takashi Kirino ◽  
Shuhei Mitani ◽  
...  
Keyword(s):  
Atomic Force Microscopy ◽  
Dielectric Breakdown ◽  
Oxide Semiconductor ◽  
Conductive Atomic Force Microscopy ◽  
Mos Capacitors ◽  
Step Bunching ◽  
Force Microscopy ◽  
Line Scan ◽  
Mos Devices ◽  
Atomic Force

The dielectric breakdown mechanism in 4H-SiC metal-oxide-semiconductor (MOS) devices was studied using conductive atomic force microscopy (C-AFM). We performed time-dependent dielectric breakdown (TDDB) measurements using a line scan mode of C-AFM, which can characterize nanoscale degradation of dielectrics. It was found that the Weibull slope () of time-to-breakdown (tBD) statistics in 7-nm-thick thermal oxides on SiC substrates was much larger for the C-AFM line scan than for the common constant voltage stress TDDB tests on MOS capacitors, suggesting the presence of some weak spots in the oxides. Superposition of simultaneously obtained C-AFM topographic and current map images of SiO2/SiC structure clearly demonstrated that most of breakdown spots were located at step bunching. These results indicate that preferential breakdown at step bunching due to local electric field concentration is the probable cause of poor gate oxide reliability of 4H-SiC MOS devices.

Conductive atomic force microscopy studies on dielectric breakdown behavior of ultrathin Al2O3 films

2011 ◽  
Vol 98 (9) ◽  
pp. 092902 ◽  
Author(s):  
K. Ganesan ◽  
S. Ilango ◽  
S. Mariyappan ◽  
M. Farrokh Baroughi ◽  
M. Kamruddin ◽  
...  
Keyword(s):  
Atomic Force Microscopy ◽  
Dielectric Breakdown ◽  
Conductive Atomic Force Microscopy ◽  
Force Microscopy ◽  
Atomic Force ◽  
Al2o3 Films

Conductive Atomic Force Microscopy Studies on the Reliability of Thermally Oxidized SiO2/4H-SiC

2007 ◽  
Vol 556-557 ◽  
pp. 501-504 ◽  
Author(s):  
Patrick Fiorenza ◽  
Raffaella Lo Nigro ◽  
Vito Raineri ◽  
Dario Salinas
Keyword(s):  
Atomic Force Microscopy ◽  
Dielectric Breakdown ◽  
Oxide Semiconductor ◽  
Large Area ◽  
Conductive Atomic Force Microscopy ◽  
Force Microscopy ◽  
Atomic Force ◽  
Thermal Oxide ◽  
Direct Measurements ◽  
Exponential Trend

The nano-characterization of thermal oxides grown on 4H-SiC is for the first time presented and analysed to derive its reliability. The dielectric breakdown (BD) kinetics of silicon dioxide (SiO2) thin films thermally grown on 4H-SiC has been determined by comparison between I-V measurements on large-area (up to 1.96×10-5 cm2) metal-oxide-semiconductor (MOS) structures and conductive atomic force microscopy (C-AFM) with a resolution of a few nanometers. C-AFM clearly images the weak breakdown single spots under constant voltage stresses. The stress time on the single C-AFM tip dot has been varied from 1×10-3 to 1×10-1 s. The density of BD spots, upon increasing the stress time, exhibits an exponential trend. The Weibull slope and the characteristic time of the dielectric BD events were so determined by direct measurements at nanometer scale demonstrating that the percolation model is valid for thin thermal oxide layers on 4H-SiC (5-7nm), but it fails for larger thicknesses (10 nm).

Fault Isolation of MOL and FEOL Buried Defects Using Conductive Atomic Force Microscopy as a Complement to Passive Voltage Contrast Imaging

2017 ◽  
Author(s):  
Lucile C. Teague Sheridan ◽  
Linda Conohan ◽  
Chong Khiam Oh
Keyword(s):  
Atomic Force Microscopy ◽  
Cmos Technology ◽  
Fault Isolation ◽  
Contrast Imaging ◽  
Conductive Atomic Force Microscopy ◽  
Isolation Technique ◽  
Conductive Afm ◽  
Force Microscopy ◽  
Atomic Force ◽  
Voltage Contrast

Abstract Atomic force microscopy (AFM) methods have provided a wealth of knowledge into the topographic, electrical, mechanical, magnetic, and electrochemical properties of surfaces and materials at the micro- and nanoscale over the last several decades. More specifically, the application of conductive AFM (CAFM) techniques for failure analysis can provide a simultaneous view of the conductivity and topographic properties of the patterned features. As CMOS technology progresses to smaller and smaller devices, the benefits of CAFM techniques have become apparent [1-3]. Herein, we review several cases in which CAFM has been utilized as a fault-isolation technique to detect middle of line (MOL) and front end of line (FEOL) buried defects in 20nm technologies and beyond.

Fault Localization in Contact Level by Using Conductive Atomic Force Microscopy

2003 ◽  
Author(s):  
Jon C. Lee ◽  
J. H. Chuang
Keyword(s):  
Atomic Force Microscopy ◽  
Integrated Circuits ◽  
Fault Localization ◽  
Electrical Characterization ◽  
Conductive Atomic Force Microscopy ◽  
Force Microscopy ◽  
Atomic Force ◽  
Optical Electron ◽  
Defect Isolation ◽  
Voltage Contrast

Abstract As integrated circuits (IC) have become more complicated with device features shrinking into the deep sub-micron range, so the challenge of defect isolation has become more difficult. Many failure analysis (FA) techniques using optical/electron beam and scanning probe microscopy (SPM) have been developed to improve the capability of defect isolation. SPM provides topographic imaging coupled with a variety of material characterization information such as thermal, magnetic, electric, capacitance, resistance and current with nano-meter scale resolution. Conductive atomic force microscopy (C-AFM) has been widely used for electrical characterization of dielectric film and gate oxide integrity (GOI). In this work, C-AFM has been successfully employed to isolate defects in the contact level and to discriminate various contact types. The current mapping of C-AFM has the potential to identify micro-leaky contacts better than voltage contrast (VC) imaging in SEM. It also provides I/V information that is helpful to diagnose the failure mechanism by comparing I/V curves of different contact types. C-AFM is able to localize faulty contacts with pico-amp current range and to characterize failure with nano-meter scale lateral resolution. C-AFM should become an important technique for IC fault localization. FA examples of this technique will be discussed in the article.

Sign in / Sign up

Export Citation Format

Share Document