scholarly journals Exposition of semiconducting and ferromagnetic properties of pulsed-laser-deposited thin films of LaFe1−xNixO3 (x=0.3, 0.4, and 0.5)

2005 ◽  
Vol 87 (13) ◽  
pp. 132104 ◽  
Author(s):  
R. J. Choudhary ◽  
Ravi Kumar ◽  
M. Wasi Khan ◽  
J. P. Srivastava ◽  
S. I. Patil ◽  
...  
Keyword(s):  
Thin Films ◽  
Pulsed Laser ◽  
Ferromagnetic Properties

Ferromagnetic properties of epitaxial La2NiMnO6 thin films grown by pulsed laser deposition

2009 ◽  
Vol 94 (13) ◽  
pp. 132506 ◽  
Author(s):  
M. Kitamura ◽  
I. Ohkubo ◽  
M. Kubota ◽  
Y. Matsumoto ◽  
H. Koinuma ◽  
...  
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
Ferromagnetic Properties

Modification of the Ferromagnetic Properties of Si1 –xMnx Thin Films Synthesized by Pulsed Laser Deposition with a Variation in the Buffer-Gas Pressure

2018 ◽  
Vol 52 (11) ◽  
pp. 1424-1427 ◽  
Author(s):  
O. A. Novodvorsky ◽  
V. A. Mikhalevsky ◽  
D. S. Gusev ◽  
A. A. Lotin ◽  
L. S. Parshina ◽  
...  
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Gas Pressure ◽  
Laser Deposition ◽  
Buffer Gas ◽  
Ferromagnetic Properties

Observations on the growth of YBa2Cu3O7-δ thin films on MgO by pulsed-laser ablation

1991 ◽  
Vol 49 ◽  
pp. 1068-1069
Author(s):  
M. Grant Norton ◽  
C. Barry Carter
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Laser Ablation ◽  
Substrate Surface ◽  
Pulsed Laser ◽  
Pulsed Laser Ablation ◽  
Thin Film Deposition ◽  
Film Deposition ◽  
Laser Ablation Process ◽  
Deposition Parameters

Pulsed-laser ablation has been widely used to produce high-quality thin films of YBa2Cu3O7-δ on a range of substrate materials. The nonequilibrium nature of the process allows congruent deposition of oxides with complex stoichiometrics. In the high power density regime produced by the UV excimer lasers the ablated species includes a mixture of neutral atoms, molecules and ions. All these species play an important role in thin-film deposition. However, changes in the deposition parameters have been shown to affect the microstructure of thin YBa2Cu3O7-δ films. The formation of metastable configurations is possible because at the low substrate temperatures used, only shortrange rearrangement on the substrate surface can occur. The parameters associated directly with the laser ablation process, those determining the nature of the process, e g. thermal or nonthermal volatilization, have been classified as ‘primary parameters'. Other parameters may also affect the microstructure of the thin film. In this paper, the effects of these ‘secondary parameters' on the microstructure of YBa2Cu3O7-δ films will be discussed. Examples of 'secondary parameters' include the substrate temperature and the oxygen partial pressure during deposition.

TEM sample preparation of wear-tested room-temperature pulsed-laser-deposited thin films of MoS2 by ultramicrotomy

1993 ◽  
Vol 51 ◽  
pp. 1118-1119
Author(s):  
Pamela F. Lloyd ◽  
Scott D. Walck
Keyword(s):  
Thin Films ◽  
Sample Preparation ◽  
Room Temperature ◽  
High Vacuum ◽  
Pulsed Laser ◽  
Ultra High Vacuum ◽  
Wear Testing ◽  
Preparation Technique ◽  
Cross Sectional ◽  
Aerospace Applications

Pulsed laser deposition (PLD) is a novel technique for the deposition of tribological thin films. MoS2 is the archetypical solid lubricant material for aerospace applications. It provides a low coefficient of friction from cryogenic temperatures to about 350°C and can be used in ultra high vacuum environments. The TEM is ideally suited for studying the microstructural and tribo-chemical changes that occur during wear. The normal cross sectional TEM sample preparation method does not work well because the material’s lubricity causes the sandwich to separate. Walck et al. deposited MoS2 through a mesh mask which gave suitable results for as-deposited films, but the discontinuous nature of the film is unsuitable for wear-testing. To investigate wear-tested, room temperature (RT) PLD MoS2 films, the sample preparation technique of Heuer and Howitt was adapted.Two 300 run thick films were deposited on single crystal NaCl substrates. One was wear-tested on a ball-on-disk tribometer using a 30 gm load at 150 rpm for one minute, and subsequently coated with a heavy layer of evaporated gold.

Pulsed laser deposition of PbMg1/3Nb2/3O3 thin films and PbMg1/3Nb2/3O3/PbTiO3 multilayers

2001 ◽  
Vol 11 (PR11) ◽  
pp. Pr11-65-Pr11-69
Author(s):  
N. Lemée ◽  
H. Bouyanfif ◽  
J. L. Dellis ◽  
M. El Marssi ◽  
M. G. Karkut ◽  
...  
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Laser Deposition

SrBi2Nb2O9 ferroelectric thin films deposited by pulsed laser deposition on textured and epitaxied platinum electrodes

2001 ◽  
Vol 11 (PR11) ◽  
pp. Pr11-133-Pr11-137
Author(s):  
J. R. Duclère ◽  
M. Guilloux-Viry ◽  
A. Perrin ◽  
A. Dauscher ◽  
S. Weber ◽  
...  
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Ferroelectric Thin Films ◽  
Laser Deposition ◽  
Platinum Electrodes

PULSED LASER IRRADIATION OF NICKEL THIN FILMS ON SILICON

1983 ◽  
Vol 44 (C5) ◽  
pp. C5-449-C5-454 ◽  
Author(s):  
P. Baeri ◽  
M. G. Grimaldi ◽  
E. Rimini ◽  
G. Celotti
Keyword(s):  
Thin Films ◽  
Laser Irradiation ◽  
Pulsed Laser ◽  
Nickel Thin Films ◽  
Pulsed Laser Irradiation

Microstructural and Electrical Characterization of Barium Strontium Titanatebased Solid Solution Thin Films Deposited on Ceramic Substrates by Pulsed Laser Deposition

2002 ◽  
Vol 720 ◽  
Author(s):  
Costas G. Fountzoulas ◽  
Daniel M. Potrepka ◽  
Steven C. Tidrow
Keyword(s):  
Thin Films ◽  
Dielectric Constant ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Electrical Characterization ◽  
Field Variable ◽  
Laser Deposition ◽  
X Ray Diffraction ◽  
Ceramic Substrates ◽  
Nominal Thickness

AbstractFerroelectrics are multicomponent materials with a wealth of interesting and useful properties, such as piezoelectricity. The dielectric constant of the BSTO ferroelectrics can be changed by applying an electric field. Variable dielectric constant results in a change in phase velocity in the device allowing it to be tuned in real time for a particular application. The microstructure of the film influences the electronic properties which in turn influences the performance of the film. Ba0.6Sr0.4Ti1-y(A 3+, B5+)yO3 thin films, of nominal thickness of 0.65 μm, were synthesized initially at substrate temperatures of 400°C, and subsequently annealed to 750°C, on LaAlO3 (100) substrates, previously coated with LaSrCoO conductive buffer layer, using the pulsed laser deposition technique. The microstructural and physical characteristics of the postannealed thin films have been studied using x-ray diffraction, scanning electron microscopy, and nano indentation and are reported. Results of capacitance measurements are used to obtain dielectric constant and tunability in the paraelectric (T>Tc) regime.

Sign in / Sign up

Export Citation Format

Share Document