Dielectric Constant of Liquid Sulfur Hexafluoride

1959 ◽  
Vol 31 (2) ◽  
pp. 572-573 ◽  
Author(s):  
Daniel Berg
Keyword(s):  
Dielectric Constant ◽  
Sulfur Hexafluoride ◽  
Liquid Sulfur

Raman Studies of Molecular Reorientation in Liquid Sulfur Hexafluoride

1974 ◽  
Vol 52 (13) ◽  
pp. 1209-1214 ◽  
Author(s):  
S. Sunder ◽  
R. E. D. McClung
Keyword(s):  
Sulfur Hexafluoride ◽  
Fourier Transforms ◽  
Raman Band ◽  
Rotational Diffusion ◽  
Diffusion Limit ◽  
Molecular Reorientation ◽  
Rotation Tensor ◽  
Liquid Sulfur ◽  
Correlation Times ◽  
Tensor Formula

The contour of the v2 Raman band of SF6 liquid has been studied over the temperature range 226–315 K. Reorientational and angular momentum correlation times were obtained by comparing the Fourier transforms of the band contours with the reorientational correlation functions calculated using the J diffusion limit of the extended rotational diffusion model. A reanalysis of Hackleman and Hubbard's nuclear relaxation data for liquid SF6, using the correlation times obtained from the Raman studies, yields the value ± 6.2 × 104 s−1 for the asymmetry in the spin–rotation tensor [Formula: see text] for fluorine nuclei in SF6.

Study of Heating Device for Sulfur Hexafluoride Gasification

2020 ◽  
Vol 18 (2) ◽  
pp. 157-163
Author(s):  
Hong Yu ◽  
Maoyong Cao ◽  
Tanbo Zhu ◽  
Fanming Liu
Keyword(s):  
Sulfur Hexafluoride ◽  
Steel Cylinder ◽  
Liquid Sulfur ◽  
Heating Device ◽  
Gas Insulated Switchgear ◽  
Temperature And Humidity ◽  
Speed Up ◽  
Specific Temperature

Sulfur hexafluoride (SF6) gas has been used to gas-insulated switchgear (GIS) because of its insulation properties and extinguishing characteristics. The processing of liquid sulfur hexafluoride from cylinders into GIS is endothermic. The processing gas inflation always leads to decrease SF6 gas inflation speed due to the lack of heat supplement and the infiltrated moisture will stick on the GIS equipment, especially at the valve outlet. In the paper, a heater detection device for sulfur hexafluoride (SF6) steel cylinder is developed. The new heater device will monitor and display the specific temperature and humidity of the valve outlet instantaneously and then heat and dry the sulfur hexafluoride (SF6) steel cylinder with automatic and stability. Then it helps to speed up the sulfur hexafluoride gasification. Meanwhile, the whole device is portable in safety.

The dielectric constant of liquid sulfur

1986 ◽  
Vol 84 (12) ◽  
pp. 6984-6988 ◽  
Author(s):  
S. C. Greer
Keyword(s):  
Dielectric Constant ◽  
Liquid Sulfur

Microstructural characterization of YBaCuO Films on LaAlO3 substrates

1989 ◽  
Vol 47 ◽  
pp. 180-181
Author(s):  
E. L. Hall ◽  
A. Mogro-Campero ◽  
N. Lewis ◽  
L. G. Turner
Keyword(s):  
Dielectric Constant ◽  
Single Crystal ◽  
Film Growth ◽  
Microstructural Characterization ◽  
Lattice Parameter ◽  
Film Plane ◽  
Substrate Material ◽  
High Loss ◽  
Amorphous Substrates ◽  
High Dielectric

There have been a large number of recent studies of the growth of Y-Ba-Cu-O thin films, and these studies have employed a variety of substrates and growth techniques. To date, the highest values of Tc and Jc have been found for films grown by sputtering or coevaporation on single-crystal SrTiO3 substrates, which produces a uniaxially-aligned film with the YBa2Cu3Ox c-axis normal to the film plane. Multilayer growth of films on the same substrate produces a triaxially-aligned film (regions of the film have their c-axis parallel to each of the three substrate <100> directions) with lower values of Jc. Growth of films on a variety of other polycrystalline or amorphous substrates produces randomly-oriented polycrystalline films with low Jc. Although single-crystal SrTiO3 thus produces the best results, this substrate material has a number of undesireable characteristics relative to electronic applications, including very high dielectric constant and a high loss tangent at microwave frequencies. Recently, Simon et al. have shown that LaAlO3 could be used as a substrate for YBaCuO film growth. This substrate is essentially a cubic perovskite with a lattice parameter of 0.3792nm (it has a slight rhombohedral distortion at room temperature) and this material exhibits much lower dielectric constant and microwave loss tangents than SrTiO3. It is also interesting from a film growth standpoint since it has a slightly smaller lattice parameter than YBa2Cu3Ox (a=0.382nm, b=c/3=0.389nm), while SrTiO3 is slightly larger (a=0.3905nm).

Enhanced performance of supercapacitors by constructing a “mini parallel-plate capacitor” in an electrode with high dielectric constant materials

2020 ◽  
Vol 8 (32) ◽  
pp. 16661-16668
Author(s):  
Huayao Tu ◽  
Shouzhi Wang ◽  
Hehe Jiang ◽  
Zhenyan Liang ◽  
Dong Shi ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Carbon Fiber ◽  
Parallel Plate ◽  
Sandwich Structure ◽  
High Dielectric Constant ◽  
Parallel Plate Capacitor ◽  
Plate Capacitor ◽  
Fiber Metal ◽  
High Dielectric ◽  
Mini Plate

The carbon fiber/metal oxide/metal oxynitride layer sandwich structure is constructed in the electrode to form a mini-plate capacitor. High dielectric constant metal oxides act as dielectric to increase their capacitance.

Ultrahigh Energy Storage Performances of Polymer-based Nanocomposite via Interfaces Engneering

2020 ◽  
Author(s):  
Peng Wang ◽  
Zhongbin Pan ◽  
Weilin Wang ◽  
Jianxu Hu ◽  
Jinjun Liu ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Energy Storage ◽  
High Performance ◽  
Breakdown Strength ◽  
Composite Films ◽  
Power Electronic ◽  
Ultrahigh Energy

High-performance electrostatic capacitors are in urgent demand owing to the rapidly development of advanced power electronic applications. However, polymer-based composite films with both high breakdown strength (Eb) and dielectric constant...

Sign in / Sign up

Export Citation Format

Share Document