Stray grain formation in single crystal Ni-base superalloy welds

2003 ◽  
Vol 94 (6) ◽  
pp. 4203-4209 ◽  
Author(s):  
J.-W. Park ◽  
S. S. Babu ◽  
J. M. Vitek ◽  
E. A. Kenik ◽  
S. A. David
Keyword(s):  
Single Crystal ◽  
Grain Formation ◽  
Stray Grain ◽  
Base Superalloy

Stray Grain Formation in Welds of Single-Crystal Ni-Base Superalloy CMSX-4

2009 ◽  
Vol 41 (1) ◽  
pp. 181-193 ◽  
Author(s):  
T. D. Anderson ◽  
J. N. DuPont ◽  
T. DebRoy
Keyword(s):  
Single Crystal ◽  
Grain Formation ◽  
Stray Grain ◽  
Base Superalloy

A New Strategy to Inhibit of Stray Grain Formation During Laser Directed Solidification of Single Crystal Superalloys

2021 ◽  
Author(s):  
Jiawei Wang ◽  
Huaming Wang ◽  
Kangjie Li ◽  
Bo Zhang ◽  
Meiling Zhang ◽  
...  
Keyword(s):  
Single Crystal ◽  
Grain Formation ◽  
New Strategy ◽  
Stray Grain

Numerical Analysis of Stray Grain Formation during Laser Welding Nickel-Based Single-Crystal Superalloy Part II: Multicomponent Dendrite Growth

2021 ◽  
Vol 1033 ◽  
pp. 31-39
Author(s):  
Zhi Guo Gao
Keyword(s):  
Single Crystal ◽  
Weld Pool ◽  
Heat Input ◽  
Dendrite Growth ◽  
Solidification Cracking ◽  
Growth Region ◽  
Dendrite Trunk ◽  
Solidification Interface ◽  
Grain Formation ◽  
Stray Grain

Multicomponent dendrite growth is theoretically predicted to optimize solidification cracking susceptibility during ternary Ni-Cr-Al nickel-based single-crystal superalloy weld pool solidification. The distribution of dendrite trunk spacing along the weld pool solidification interface is clearly symmetrical about the weld pool centerline in beneficial (001)/[100] welding configuration. The distribution of dendrite trunk spacing along the weld pool solidification interface is crystallography-dependent asymmetrical from bottom to top surface of the weld pool in detrimental (001)/[110] welding configuration. The smaller heat input is used, the finer dendrite trunk spacing is kinetically promoted by less solute enrichment and narrower constitutional undercooling ahead of solid/liquid interface with mitigation of metallurgical contributing factors for solidification cracking and vice versa. Vulnerable [100] dendrite growth region is predominantly suppressed and epitaxial [001] dendrite growth region is favored to spontaneously facilitate single-crystal columnar dendrite growth and reduce microstructure anomalies with further reduction of heat input. Optimum low heat input (both lower laser power and higher welding speed) with (001)/[100] welding configuration is the most favorable one to avoid nucleation and growth of stray grain formation, minimize both dendrite trunk spacing and solidification cracking susceptibility potential, improve resistance to solidification cracking, and ameliorate weldability and weld integrity through microstructure modification instead of inappropriate high heat input (both higher laser power and slower welding speed) with (001)/[110] welding configuration. The dendrite trunk spacing in the [100] dendrite growth region on the right side of the weld pool is considerably coarser and grows faster than that within the [010] dendrite growth region of the left side in the (001)/[110] welding configuration to deteriorate weldability, although the welding conditions are the same on the either side. Furthermore, the alternative mechanism of crystallography-dependent solidification cracking as consequence of asymmetrical microstructure development and diffusion-controlled dendrite growth of γ phase is therefore proposed. The theoretical predictions are comparable with experiment results. The reliable model is also useful for welding conditions optimization for crack-free laser processing.

scholarly journals Numerical Analysis of Solidification Behavior during Laser Welding Nickel-based Single-crystal Superalloy Part IV: Optimization of Thermo-metallurgical Factors

2021 ◽  
Vol 1996 (1) ◽  
pp. 012004
Author(s):  
Zhiguo Gao
Keyword(s):  
Single Crystal ◽  
Welding Speed ◽  
Laser Power ◽  
Liquid Interface ◽  
Solidification Behavior ◽  
Dendrite Morphology ◽  
Grain Formation ◽  
Solid Liquid Interface ◽  
Solid Liquid ◽  
Stray Grain

Abstract Important metallurgical factors, such as alloying aluminum redistribution, supersaturation and undercooling of dendrite tip around solid/liquid interface, are separately optimized to alleviate stray grain formation and columnar/equiaxed transition (CET) with series of welding conditions and provide a very efficient method for microstructure control through modification of growth kinetics of dendrite tip under nonequilibrium solidification conditions of ternary Ni-Cr-Al molten pool. Asymmetrical (001)/[110] welding configuration is inferior to symmetrical (001)/[100] welding configuration, because overall area-weighted alloying redistribution, supersaturation and undercooling of dendrite tip throughout the solid/liquid interface of weld pool are consistently severer to exacerbate solidification behavior and microstructure development and incur morphology instability of columnar/equiaxed transition. High heat input, such as combination of higher laser power and slower welding speed, monotonically increases aluminum enrichment, supersaturation and undercooling of dendrite tip near solidification interface to simultaneously deteriorate nucleation and growth of stray grain formation and weaken columnar dendrite morphology, while low heat input, such as combination of lower laser power and faster welding speed, decreases solute buildup, relieves supersaturation and beneficially suppresses dendrite tip undercooling to minimize equiaxed dendrite morphology in the crack-susceptible region, and thereby facilitate single-crystal epitaxial growth with decrease of thermo-metallurgical factors for columnar/equiaxed transition in order to provide prerequisite for optimization of welding conditions. Favorable solidification conditions are obtainable with preferential crystallographic orientation to eliminate columnar/equiaxed transition under which the epitaxy of single-crystal metallurgical properties across fusion boundary of substrate is predominantly promoted to essentially reduce stray grain formation in (001)/[100] welding configuration, and is kinetically capable of significant reduction of microstructure anomalies and nonuniform solidification behavior. The useful relationship among welding conditions, alloying aluminum redistribution, supersaturation and undercooling of dendrite tip is properly established within dendrite stability range through thorough analysis. In addition, the validation of theoretical predictions is fairly reasonable by the experiment results. It is worth that the contributions of kinetics-related solidification phenomena with advancement of solid/liquid interface are imposed altogether to understand why stray grain formation occurs on the basis of controlling mechanism of minimum undercooling or minimum velocity by the reproducible methodology procedure.

Orientation Imaging Microscopy of Stray Grain Formation in Single Crystal Weld Structures

2008 ◽  
Vol 14 (S2) ◽  
pp. 40-41
Author(s):  
T Anderson ◽  
J DuPont ◽  
T DebRoy
Keyword(s):  
New Mexico ◽  
Single Crystal ◽  
Orientation Imaging Microscopy ◽  
Orientation Imaging ◽  
Grain Formation ◽  
Stray Grain

Extended abstract of a paper presented at Microscopy and Microanalysis 2008 in Albuquerque, New Mexico, USA, August 3 – August 7, 2008

Sign in / Sign up

Export Citation Format

Share Document