Saturation pool boiling of HFE-7100 dielectric liquid in a simulated reduced gravity

2002 ◽  
Author(s):  
Mohamed S. El-Genk ◽  
Huseyin Bostanci
Keyword(s):  
Pool Boiling ◽  
Dielectric Liquid ◽  
Reduced Gravity

Synthetic jet enhancement of natural convection and pool boiling in a dielectric liquid

2002 ◽  
Author(s):  
Jivtesh Garg ◽  
Mehmet Arik ◽  
Avram Bar-Cohen ◽  
Rex Wolf ◽  
Bojan Vukasinovic ◽  
...  
Keyword(s):  
Natural Convection ◽  
Pool Boiling ◽  
Synthetic Jet ◽  
Dielectric Liquid

Numerical Simulation and Experimental Validation of the Dynamics of a Single Bubble During Pool Boiling Under Constant and Time-Varying Reduced Gravity Conditions

2003 ◽  
Author(s):  
H. S. Abarajith ◽  
D. M. Qiu ◽  
V. K. Dhir
Keyword(s):  
Numerical Simulation ◽  
Heated Surface ◽  
Bubble Diameter ◽  
Pool Boiling ◽  
Growth Period ◽  
Single Bubble ◽  
Time Varying ◽  
Reduced Gravity ◽  
System Pressure ◽  
Vapor Liquid

The numerical simulation and experimental validations of the growth and departure of a single bubble on a horizontal heated surface during pool boiling under reduced gravity conditions have been performed here. A finite difference scheme is used to solve the equations governing mass, momentum and energy in the vapor liquid phases. The vapor-liquid interface is captured by level set method, which is modified to include the influence of phase change at the liquid-vapor interface. The effects of reduced gravity conditions, wall superheat and liquid subcooling and system pressure on the bubble diameter and growth period have been studied. The simulations are also carried out under both constant and time-varying gravity conditions to benchmark the solution with the actual experimental conditions that existed during the parabolic flights of KC-135 aircraft. In the experiments, a single vapor bubble was produced on an artificial cavity, 10 μm in diameter microfabricated on the polished silicon wafer, the wafer was heated electrically from the back with miniature strain gage type heating elements in order to control the nucleation superheat. The bubble growth period and the bubble diameter predicted from the numerical simulations have been found to compare well with the data from experiments.

Pool Boiling of n-Pentane, CFC-113, and Water Under Reduced Gravity: Parabolic Flight Experiments With a Transparent Heater

1995 ◽  
Vol 117 (2) ◽  
pp. 408-417 ◽  
Author(s):  
T. Oka ◽  
Y. Abe ◽  
Y. H. Mori ◽  
A. Nagashima
Keyword(s):  
Heat Transfer ◽  
Parabolic Flight ◽  
Pool Boiling ◽  
Glass Plate ◽  
Nucleate Boiling ◽  
Heat Fluxes ◽  
Rear Side ◽  
Heater Surface ◽  
Reduced Gravity ◽  
Liquid Behavior

A series of pool boiling experiments have been conducted under reduced gravity condition (the order of 10−2 times the terrestrial gravity) available in an aircraft taking parabolic flight. A transparent resistant heater, a transparent indium oxide film plated on a glass plate, was employed so that the vapor/liquid behavior interacting with the heater surface could be observed from the rear side of the heater simultaneously with the side view of vapor bubbles above the heater surface. The experiments were performed for three different fluids—n-pentane, CFC-113, and water—under subcooled conditions. The critical heat fluxes for both n-pentane and CFC-113 under the reduced gravity were lowered to about 40 percent of the corresponding terrestrial values. Although the heat transfer characteristics in a low heat flux nucleate boiling regime for both n-pentane and CFC-113 showed no more than a slight change with the reduction in gravity, a significant heat transfer deterioration was noted with water in the reduced gravity boiling. The observation from the rear side of the heater suggested that this particular difference in the gravity dependency of heat transfer was ascribed to a considerable difference, between the organic fluids and water, in the behavior of attachment to the heater surface of the bubbles grown up, while the behavior of attachment must depend on the surface tension of each fluid and the wettability of the heater surface with the fluid.

Experimental Verification of Analytical Prediction of Pool Boiling CHF Incorporating the Effects of EHD and Contact Angle

2015 ◽  
Author(s):  
Ichiro Kano ◽  
Takahiro Sato ◽  
Naoki Okamoto
Keyword(s):  
Heat Transfer ◽  
Contact Angle ◽  
Electric Field ◽  
Boiling Heat Transfer ◽  
Pool Boiling ◽  
Contact Angles ◽  
Dielectric Liquid ◽  
Working Fluid ◽  
Analytical Prediction ◽  
Compound Effect

Boiling heat transfer enhancement via compound effect of Electro-Hydro-Dynamic (EHD) and contact angle has been experimentally and analytically investigated. A fluorinated dielectric liquid (Asahi Glass Co. Ltd, AE-3000) was selected as the working fluid. Pool boiling heat transfer in the saturated liquid was measured at atmospheric pressure. In order to change the contact angle between the boiling surface and the dielectric liquid, the different materials Cu, Cr, NiB, Sn, and mixture of 5 and 1.5 micro meter diamond particles were electrically deposited on a boiling surface. The critical heat flux (CHF) for different contact angles showed 20.5 ∼ 26.9 W/cm2 which was −7 ∼ 25 % of that for a non-coated Cu surface (21.5 W/cm2). Upon application of a −5 kV/mm electric field to the micro structured surface (the mixture of 5 and 1.5 micro meter particles), a CHF of 99 W/cm2 at a superheat of 33.5 K was obtained. The previous theoretical equation of pool boiling predicted the CHF with the electric field and without the electrode.

Self-Propelled Sliding Bubble Motion Induced by Surface Microstructure in Pool Boiling of a Dielectric Fluid Under Microgravity

2015 ◽  
Vol 137 (2) ◽  
Author(s):  
Naveenan Thiagarajan ◽  
Sushil H. Bhavnani ◽  
Vinod Narayanan
Keyword(s):  
Vapor Bubble ◽  
Bubble Dynamics ◽  
Heated Surface ◽  
Pool Boiling ◽  
Bubble Nucleation ◽  
Radius Of Curvature ◽  
Dielectric Fluid ◽  
Bubble Motion ◽  
Reduced Gravity ◽  
Modification Technique

This paper reports bubble dynamics observed during pool boiling over microstructures with an asymmetric saw-tooth cross section, under reduced gravity. The periodic saw-toothed ratchets etched on a silicon surface include fabricated vapor bubble nucleation sites only on the shallow slope. Reduced gravity pool boiling experiments were conducted aboard a Boeing 727 aircraft carrying out parabolic maneuvers. The fluid used was FC-72, a highly wetting dielectric fluid used as a coolant for electronics. Under microgravity, it was observed that the bubble diameters were six times larger than in terrestrial gravity. Also, self-propelled sliding bubble motion along the surface of the saw teeth was observed in reduced gravity. The velocity of the sliding bubbles across the saw teeth, following lateral departure from the cavities, was measured to be as high as 27.4 mm/s. A model for the sliding bubble motion is proposed by attributing it to the force due to pressure differences that arise in the liquid film between the vapor bubble and the saw-toothed heated surface. The pressure difference is due to difference in the radius of curvature of the interface between the crest and trough of the saw teeth. The surface modification technique, which resulted in the sliding bubble motion, has the potential to alleviate dry-out caused due to stagnant vapor bubbles over heat sources under microgravity when the buoyancy forces are negligible compared to the surface tension forces.

An Investigation of the Effect of Inclination on Critical Heat Flux of PF-5060 Dielectric Liquid on Microporous Copper Surfaces

2013 ◽  
Author(s):  
Amir F. Ali ◽  
Mohamed S. El-Genk
Keyword(s):  
Experimental Data ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Inclination Angle ◽  
Pool Boiling ◽  
Dielectric Liquid ◽  
Copper Surfaces ◽  
Electrochemical Processes ◽  
Inclination Angles

Pool boiling experiments investigated the effect of inclination angle on the Critical Heat Flux (CHF) for saturation boiling of PF-5060 dielectric liquid on MicroPorous Copper (MPC) surfaces of different thicknesses (80 to 230 μm). The morphology of the surfaces, deposited using electrochemical processes, vary with the thickness, and hence CHF. The inclination angles investigated are 0° (upward facing), 60°, 90° (vertical), 120°, 150°, 160°, 170° and 180° (downward facing). CHF decreases with decreasing MPC thickness and/or increasing inclination angle. The CHF values in the upward facing orientation are 39%–67% higher than on smooth, polished Cu. For all MPC surfaces, CHF values in the downward facing orientation are ∼ 28% of those in the upward facing orientation (0°). The developed CHF correlation accounts for the effects of MPC thickness and inclination angle and is in agreement with experimental data to within ± 8%.

Nucleate Pool Boiling of Water in Normal and Reduced Gravity Environments

1994 ◽  
Author(s):  
Bruce W. Webbon ◽  
Boris Yendler ◽  
John B. Miles
Keyword(s):  
Pool Boiling ◽  
Nucleate Pool Boiling ◽  
Reduced Gravity
Sign in / Sign up

Export Citation Format

Share Document