Erratum: “Modeling the effect of grain size and dislocation density on hysteretic magnetic properties in steels” [J. Appl. Phys. 89, 5610 (2001)]

2001 ◽  
Vol 90 (4) ◽  
pp. 2051-2051 ◽  
Author(s):  
M. J. Sablik
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Dislocation Density ◽  
Hysteretic Magnetic Properties

Holocene climate recorded by magnetic properties of lake sediments in the Northern Rocky Mountains, USA

The Holocene ◽  
2019 ◽  
Vol 30 (3) ◽  
pp. 479-484
Author(s):  
Daniel P Maxbauer ◽  
Mark D Shapley ◽  
Christoph E Geiss ◽  
Emi Ito
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Rocky Mountains ◽  
Future Research ◽  
Magnetic Minerals ◽  
Holocene Climate ◽  
Northern Rocky Mountains ◽  
The North ◽  
Lake Bottom ◽  
Northern Rockies

We present two hypotheses regarding the evolution of Holocene climate in the Northern Rocky Mountains that stem from a previously unpublished environmental magnetic record from Jones Lake, Montana. First, we link two distinct intervals of fining magnetic grain size (documented by an increasing ratio of anhysteretic to isothermal remanent magnetization) to the authigenic production of magnetic minerals in Jones Lake bottom waters. We propose that authigenesis in Jones Lake is limited by rates of groundwater recharge and ultimately regional hydroclimate. Second, at ~8.3 ka, magnetic grain size increases sharply, accompanied by a drop in concentration of magnetic minerals, suggesting a rapid termination of magnetic mineral authigenesis that is coeval with widespread effects of the 8.2 ka event in the North Atlantic. This association suggests a hydroclimatic response to the 8.2 ka event in the Northern Rockies that to our knowledge is not well documented. These preliminary hypotheses present compelling new ideas that we hope will both highlight the sensitivity of magnetic properties to record climate variability and attract more work by future research into aridity, hydrochemical response, and climate dynamics in the Northern Rockies.

scholarly journals Investigation of Polyol Process for the Synthesis of Highly Pure BiFeO3 Ovoid-Like Shape Nanostructured Powders

Nanomaterials ◽  
2019 ◽  
Vol 10 (1) ◽  
pp. 26 ◽  
Author(s):  
Manel Missaoui ◽  
Sandrine Coste ◽  
Maud Barré ◽  
Anthony Rousseau ◽  
Yaovi Gagou ◽  
...  
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
High Purity ◽  
Average Crystallite Size ◽  
Polyol Process ◽  
Pure Bifeo3 ◽  
Optimum Parameters ◽  
Mössbauer Measurements ◽  
Synthesis Protocol ◽  
Nanostructured Powders

Exclusive and unprecedented interest was accorded in this paper to the synthesis of BiFeO3 nanopowders by the polyol process. The synthesis protocol was explored and adjusted to control the purity and the grain size of the final product. The optimum parameters were carefully established and an average crystallite size of about 40 nm was obtained. XRD and Mössbauer measurements proved the high purity of the synthesized nanostructurated powders and confirmed the persistence of the rhombohedral R3c symmetry. The first studies on the magnetic properties show a noticeable widening of the hysteresis loop despite the remaining cycloidal magnetic structure, promoting the enhancement of the ferromagnetic order and consequently the magnetoelectric coupling compared to micrometric size powders.

scholarly journals A model for hysteretic magnetic properties under the application of noncoaxial stress and field

1993 ◽  
Vol 74 (1) ◽  
pp. 480-488 ◽  
Author(s):  
M. J. Sablik ◽  
S. W. Rubin ◽  
L. A. Riley ◽  
D. C. Jiles ◽  
D. A. Kaminski ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Hysteretic Magnetic Properties

Computation on continuous grain refinement in AA1050 aluminum during repetitive tube expansion and shrinking technique

2015 ◽  
Vol 232 (4) ◽  
pp. 307-318
Author(s):  
H Jafarzadeh ◽  
K Abrinia
Keyword(s):  
Finite Element Method ◽  
Plastic Deformation ◽  
Grain Size ◽  
Finite Element ◽  
Dislocation Density ◽  
Severe Plastic Deformation ◽  
Grain Refinement ◽  
Half Cycle ◽  
Tube Expansion ◽  
Element Method

The microstructure evolution during recently developed severe plastic deformation method named repetitive tube expansion and shrinking of commercially pure AA1050 aluminum tubes has been studied in this paper. The behavior of the material under repetitive tube expansion and shrinking including grain size and dislocation density was simulated using the finite element method. The continuous dynamic recrystallization of AA1050 during severe plastic deformation was considered as the main grain refinement mechanism in micromechanical constitutive model. Also, the flow stress of material in macroscopic scale is related to microstructure quantities. This is in contrast to the previous approaches in finite element method simulations of severe plastic deformation methods where the microstructure parameters such as grain size were not considered at all. The grain size and dislocation density data were obtained during the simulation of the first and second half-cycles of repetitive tube expansion and shrinking, and good agreement with experimental data was observed. The finite element method simulated grain refinement behavior is consistent with the experimentally obtained results, where the rapid decrease of the grain size occurred during the first half-cycle and slowed down from the second half-cycle onwards. Calculations indicated a uniform distribution of grain size and dislocation density along the tube length but a non-uniform distribution along the tube thickness. The distribution characteristics of grain size, dislocation density, hardness, and effective plastic strain were consistent with each other.

A Study on The Phase Transformation and Exchange-Coupling of (Nd0 95La0 05)9 5FebalCo5Nb2B10.5 Nanocomposites

1999 ◽  
Vol 577 ◽  
Author(s):  
Q. Chen ◽  
B. M. Ma ◽  
B. Lu ◽  
M. Q. Huang ◽  
D. E. Laughlin
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Phase Transformation ◽  
Thermal Treatment ◽  
Grain Growth ◽  
Exchange Coupling ◽  
Phase Distribution ◽  
Maximum Energy ◽  
Treatment Temperature ◽  
Phase Identification

ABSTRACTThe phase transformation and the exchange coupling in (Ndo095Lao005)9.5FebaICOsNb 2BI05 have been investigated. Nanocomposites were obtained by treating amorphous precursors at temperatures ranging from 650TC to 9500C for 10 minutes. The magnetic properties were characterized via the vibrating sample magnetometer (VSM). X-ray diffraction (XRD), thermomagnetic analysis (TMA), and transmission electron microscopy (TEM) were used to perform phase identification, measure grain size, and analyze phase distribution. The strength of the exchange coupling between the magnetically hard and soft phases in the corresponding nanocomposite was analyzed via the AM-versus-H plot. It was found that the remanence (Br), coercivity (Hci), and maximum energy product (BHmax) obtained were affected by the magnetic phases present as well as the grain size of constituent phases and their distribution. The optimal magnetic performance, BHm, occurred between 700°C to 750°C, where the crystallization has completed without excessive grain growth. TMA and TEM indicated that the system was composed of three phases at this point, Nd2(Fe Co) 14B, ca-Fe, and Fe3B. The exchange coupling interaction among these phases was consistently described via the AM-versus-H plot up to 750°C. The Br, Hci, and BHmax degraded severely when the thermal treatment temperature increased from 750°C. This degradation may be attributed to the grain growth of the main phases, from 45 to 68nm, and the development of precipitates, which grew from 5nm at 750°C to 12nm at 850°C. Moreover, the amount of the precipitates was found to increase with the thermal treatment temperatures. The precipitates, presumably borides, may cause a decrease in the amount of the a-Fe and Fe 3B and result in a redistribution of the Co in the nanocomposites. The increase of the Co content in the Nd 2(Fe Co) 14B may explain the increase of its Curie temperature with the thermal treatment temperatures. In this paper, we examine the impacts of these factors on the magnetic properties of (Ndo 95Lao 05)9 5FebaICosNb2B10.5 nanocomposite.

Simulation of Grain Growth of Materials Produced by Severe Plastic Deformation

2011 ◽  
Vol 409 ◽  
pp. 597-602
Author(s):  
Yuichi Mizuno ◽  
Kenji Okushiro ◽  
Yoshiyuki Saito
Keyword(s):  
Plastic Deformation ◽  
Grain Size ◽  
Dislocation Density ◽  
Severe Plastic Deformation ◽  
Size Distribution ◽  
Grain Size Distribution ◽  
Boundary Migration ◽  
Interface Energy ◽  
Diffusion Reaction ◽  
Field Methods

Grain boundary migration in materials under severe plastic deformation was simulated by the phase field methods. The interface energy and dislocation density on growth kinetics were simulated on systems of 2-dimensional lattice. .In inhomogeneous systems grain size distributions in simulated grain structures were binodal distributions. The classification of the solution of differential equations based on the mean-field Hillert model describing temporal evolution of the scaled grain size distribution function was in good agreement with those given by the Computer simulations. Effect of dislocation on thermodynamic stability was taken into consideration. Dislocation density distribution was calculated by a equation based on the diffusion-reaction equation.. Scaled grain size distribution was known to be affected by the dislocation.

Effect of Nitridation Magnetic Properties of Nanocrystalline Fe-Co Alloy Powders

2010 ◽  
Vol 654-656 ◽  
pp. 1106-1109
Author(s):  
Ya Qiong He ◽  
Chang Hui Mao ◽  
Jian Yang
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Alloy Powder ◽  
High Energy ◽  
X Ray Diffraction ◽  
Powder Mixtures ◽  
X Ray ◽  
Transmission Electron ◽  
Nitridation Temperature ◽  
Microstructure And Magnetic Properties

Nanocrystalline Fe-Co alloy powders, which were prepared by high-energy mechanical milling, were nitrided under the mixing gas of NH3/H2 in the temperature range from 380°C to 510°C. X-ray diffraction (XRD) was used to analyze the grain size and reaction during the processing. The magnetic properties of the nitrided powders were measured by Vibrating Sample Magnetometer (VSM). The results show that with the appearance of Fe4N phase after nitride treatment, and the grain-size of FeCo phase decreases with the increase of nitridation temperature between 380°C to 450°C.The saturation magnetization of nitrided alloy powder treated at 480°C is about 18% higher than that of the initial Fe-Co alloy powder, accompanied by the reduction of the coercivity. Transmission electron microscope (TEM) was used, attempting to further analyze the effect of Fe4N phase on microstructure and magnetic properties of the powder mixtures.

Fabrication of Nanostructured Fe-Co Alloy Powders by Hydrogen Reduction and Its Magnetic Properties

2007 ◽  
Vol 534-536 ◽  
pp. 1389-1392
Author(s):  
Young Jung Lee ◽  
Baek Hee Lee ◽  
Gil Su Kim ◽  
Kyu Hwan Lee ◽  
Young Do Kim
Keyword(s):  
Crystal Structure ◽  
Particle Size ◽  
Grain Size ◽  
Magnetic Properties ◽  
Nanostructured Materials ◽  
Hydrogen Reduction ◽  
Internal Strain ◽  
Oxide Powder ◽  
Powder Mixtures ◽  
Effect Of Microstructure

Magnetic properties of nanostructured materials are affected by the microstructures such as grain size (or particle size), internal strain and crystal structure. Thus, it is necessary to study the synthesis of nanostructured materials to make significant improvements in their magnetic properties. In this study, nanostructured Fe-20at.%Co and Fe-50at.%Co alloy powders were prepared by hydrogen reduction from the two oxide powder mixtures, Fe2O3 and Co3O4. Furthermore, the effect of microstructure on the magnetic properties of hydrogen reduced Fe-Co alloy powders was examined using XRD, SEM, TEM, and VSM.

Sign in / Sign up

Export Citation Format

Share Document