scholarly journals Hall cross size scaling and its application to measurements on nanometer-size iron particle arrays

2000 ◽  
Vol 76 (22) ◽  
pp. 3283-3285 ◽  
Author(s):  
S. Wirth ◽  
S. von Molnár
Keyword(s):  
Iron Particle ◽  
Nanometer Size ◽  
Size Scaling

Chemical Transformation of Fe, Air & Water to Ammonia: Variation of Reaction Rate with Temperature, Pressure, Alkalinity and Iron

2018 ◽  
Author(s):  
Ping Peng ◽  
Fang-Fang Li ◽  
Xinye Liu ◽  
Jiawen Ren ◽  
jessica stuart ◽  
...  
Keyword(s):  
Particle Size ◽  
Reaction Rate ◽  
Electrolyte Concentration ◽  
Iron Concentration ◽  
Reaction Medium ◽  
Iron Particle ◽  
Intermediate Step ◽  
Ammonia Production ◽  
Pure Nitrogen ◽  
Alkaline Reaction

The rate of ammonia production by the <u>chemical </u>oxidation of iron, N<sub>2</sub>(from air or as pure nitrogen) and water is studied as a function of (1) iron particle size, (2) iron concentration, (3) temperature, (4) pressureand (5) concentration of the alkaline reaction medium. The reaction meduium consists of an aqueous solution of equal molal concentrations of NaOH and KOH (Na<sub>0.5</sub>K<sub>0.5</sub>OH). We had previously reported on the <u>chemical </u>reaction of iron and nitrogen in alkaline medium to ammonia as an intermediate step in the <u>electrochemical </u>synthesis of ammonia by a nano-sized iron oxide electrocatlyst. Here, the intermediate <u>chemical </u>reaction step is exclusively explored. The ammonia production rate increases with temperature (from 20 to 250°C), pressure (from 1 atm to 15 atm of air or N<sub>2</sub>), and exhibits a maximum rate at an electrolyte concentration of 8 molal Na<sub>0,5</sub>K<sub>0,5</sub>OH in a sealed N<sub>2</sub>reactor. 1-3 µm particle size Fe drive the highest observed ammonia production reaction rate. The Fe mass normalized rate of ammonia production increases with decreasing added mass of the Fe reactant reaching a maximum observed rate of 2.2x10<sup>-4</sup>mole of NH<sub>3</sub>h<sup>-1</sup>g<sup>-1</sup>for the reaction of 0.1 g of 1-3 µm Fe in 200°C 8 molal Na<sub>0.5</sub>K<sub>0.5</sub>OH at 15 atm. Under these conditions 5.1 wt% of the iron reacts to form NH<sub>3</sub>via the reaction N<sub>2</sub>+ 2Fe + 3H<sub>2</sub>O ®2NH<sub>3</sub>+ Fe<sub>2</sub>O<sub>3</sub>.

scholarly journals Fluctuating Asymmetry and Developmental Instability, a Guide to Best Practice

Symmetry ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 9
Author(s):  
John H. Graham
Keyword(s):  
Measurement Error ◽  
Best Practices ◽  
Environmental Stress ◽  
Fluctuating Asymmetry ◽  
Best Practice ◽  
Developmental Instability ◽  
The Past ◽  
Size Scaling ◽  
Research Designs

Best practices in studies of developmental instability, as measured by fluctuating asymmetry, have developed over the past 60 years. Unfortunately, they are haphazardly applied in many of the papers submitted for review. Most often, research designs suffer from lack of randomization, inadequate replication, poor attention to size scaling, lack of attention to measurement error, and unrecognized mixtures of additive and multiplicative errors. Here, I summarize a set of best practices, especially in studies that examine the effects of environmental stress on fluctuating asymmetry.

Modelling and experimental characterisation of a compressional adaptive magnetorheological elastomer isolator

2021 ◽  
pp. 107754632110253
Author(s):  
Emiliano Rustighi ◽  
Diego F Ledezma-Ramirez ◽  
Pablo E Tapia-Gonzalez ◽  
Neil Ferguson ◽  
Azrul Zakaria
Keyword(s):  
Magnetic Field ◽  
Silicone Rubber ◽  
Magnetic Interaction ◽  
Iron Particle ◽  
Material Model ◽  
Rubber Matrix ◽  
Magnetorheological Elastomer ◽  
Volume Percentage ◽  
Shock Absorbers ◽  
Percent Concentration

This article proposes a simple physical-based model to describe and predict the performance of axially compressed magnetorheological elastomer cylinders used as vibration and shock absorbers. The model describes the magnetorheological elastomer macroscopic stiffness changes because of an externally applied magnetic field from a microscopic composite cell of silicone rubber and carbonyl iron particle. Despite neglecting the material hyperelasticity, anisotropy and adjacent magnetic interaction, the model describes effectively the effect of the magnetic field on the macroscopic modulus of elasticity. The changes in the mechanical properties with the induced magnetic field are measured on samples of different particle concentration based on volume percentage, that is, 10 and 30 percent concentration of iron particles in a silicone rubber matrix. The manufacturing process of the samples is detailed, as well as the experimental validation of the effective stiffness change under a magnetic field in terms of transmissibility and mobility testing. However, the prediction seems to be limited by the linear elastic material model. Predictions and measurements are compared, showing that the model is capable of predicting the tunability of the dynamic/shock absorber and that the proposed devices have a possible application in the reduction of mechanical vibrations.

Sign in / Sign up

Export Citation Format

Share Document